scholarly journals Study of critical micelle concentration of cetyltrimethylammonium bromide (CTAB) in pure water in presence and absence of magnesium sulphate and sodium sulphae by measuring conductivity meter

BIBECHANA ◽  
2014 ◽  
Vol 11 ◽  
pp. 123-127 ◽  
Author(s):  
Ajaya Bhattarai ◽  
Ghanashyam Shrivastav ◽  
Chom Nath Adhikari

The precise measurement of specific conductivity of cetyltrimethylammonium bromide (CTAB) in distilled water at room temperature was reported and also the specific conductivity of cetyltrimethylammonium bromide was measured in the presence of magnesium sulphate and sodium sulphate using a conductivity meter. The critical micelle concentration of three systems was calculated. The comparison of cmc among them was also performed. DOI: http://dx.doi.org/10.3126/bibechana.v11i0.10390 BIBECHANA 11(1) (2014) 123-127

BIBECHANA ◽  
2012 ◽  
Vol 9 ◽  
pp. 63-68 ◽  
Author(s):  
Ajaya Bhattarai ◽  
Sujit Kumar Shah ◽  
Ashok Kumar Yadav ◽  
Janak Adhikari

The precise measurement of the specific conductivity of sodium deoxycholate in pure water and ethanolwater mixed solvent media containing 0.10 and 0.20 volume fraction of ethanol at 303.15 K are reported. The concentration were varied from ~ 0.01 mol L-1 to ~ 0.0002 mol L-1.The conductivity of sodium deoxycholate decreases with the increase in the volume fraction of ethanol. The critical micelle concentration of sodium deoxycholate increases with the increase in the volume fraction of ethanol. DOI: http://dx.doi.org/10.3126/bibechana.v9i0.7176 BIBECHANA 9 (2013) 63-68


BIBECHANA ◽  
2016 ◽  
Vol 14 ◽  
pp. 77-85 ◽  
Author(s):  
Chom Nath Adhikari ◽  
G S Shrivastav ◽  
Ajaya Bhattarai

Viscosity and surface tension measurements of cetyltrimethylammonium bromide (CTAB) in presence and absence of Na2SO4 and MgSO4 in aqueous media are reported. The results showed an increase in viscosity with increase in concentration of cetyltrimethylammonium bromide in presence and absence of salts where as the decrease in surface tension with increase in concentration of cetyltrimethylammonium bromide in presence and absence of salts. The viscosity of CTAB was observed lowest in pure water and increases in presence of MgSO4 and then more increases in presence of Na2SO4 where as the surface tension of CTAB was observed highest in pure water and decreases in presence of Na2SO4 and then more decreases in presence of MgSO4.The critical micelle concentration (cmc) of CTAB decreases in presence of salts in both viscosity and surface tension measurements. The decreasing cmc of CTAB are found to be more in the presence of Na2SO4 in comparison with the presence of MgSO4 for both measurements. The graphs of viscosity versus log[C] and the surface tension versus log[C] are used in determining the critical micelle concentration (cmc).        BIBECHANA 14 (2017) 77-85


2013 ◽  
Vol 13 (1) ◽  
pp. 89-93 ◽  
Author(s):  
Ajaya Bhattarai ◽  
Sujit Kumar Shah ◽  
Ashok Kumar Yadav

The accurate measurement of the specific conductivity of cetylpyridinium chloride in pure water and ethanol-water mixed solvent media containing 0.10, 0.20, 0.30 and 0.40 volume fraction of ethanol at room temperature are reported. The concentrations were varied from ~ 0.005 mol l-1 to ~ 0.0002 mol l-1.The conductivity of cetylpyridinium chloride decreases with the increase in the volume fraction of ethanol. The critical micelle concentration of cetylpyridinium chloride increases with the increase in the volume fraction of ethanol. Nepal Journal of Science and Technology Vol. 13, No. 1 (2012) 89-93 DOI: http://dx.doi.org/10.3126/njst.v13i1.7446


BIBECHANA ◽  
2014 ◽  
Vol 11 ◽  
pp. 79-85 ◽  
Author(s):  
Kuber Limbu ◽  
Sujit Kumar Shah ◽  
Ajaya Bhattarai

The accurate measurements of surface tension of sodium dodecyl sulphate (SDS) in distilled water and in presence of 0.01M Na2SO4 and 0.01M ZnSO4 at room temperature were reported by drop weight method using a stalagmometer. The critical micelle concentration (cmc) of sodium dodecyl sulphate (SDS) in distilled water was obtained higher than in presence of Na2SO4 and ZnSO4. The decrease of cmc of sodium dodecyl sulphate in the presence of salts has been discussed. DOI: http://dx.doi.org/10.3126/bibechana.v11i0.10383 BIBECHANA 11(1) (2014) 79-85


BIBECHANA ◽  
2013 ◽  
Vol 10 ◽  
pp. 52-57 ◽  
Author(s):  
Kabita Jha ◽  
Ajaya Bhattarai ◽  
Sujeet Kumar Chatterjee

NOTE: on 27th May 2014 in the abstract, the sentence"The surface tension of cetyltrimethylammonium bromide is found less in presence of KCl than NaCl in aqueous media" was changed to read "The surface tension of cetyltrimethylammonium bromide is found more in presence of KCl than NaCl in aqueous media."In the Conclusion (p.56) the sentence"The surface tension of cetyltrimethylammonium bromide is found less in presence of KCl than NaCl in aqueous media." was changed to read"The surface tension of cetyltrimethylammonium bromide is found more in presence of KCl than NaCl in aqueous media." Precise measurements on Surface tension of cetyltrimethylammonium bromide in presence and in absence of KCl and NaCl in aqueous media are reported. The results showed a sharp decrease in surface tension with increase in concentration of cetyltrimethylammonium bromide and then almost constant value of surface tension was observed. Also, the surface tension decreases with addition of salts. The surface tension of cetyltrimethylammonium bromide is found less in presence of KCl than NaCl in aqueous media. In presence of monovalent salts, the critical micelle concentration (cmc) value decreases which is explained on the basis of the orientation of the surfactant and reduction of the free energy of the surface, thus decreasing surface tension. The graphs of surface tension versus concentration are used in determining the critical micelle concentration (cmc). BIBECHANA 10 (2014) 52-57 DOI: http://dx.doi.org/10.3126/bibechana.v10i0.9311


BIBECHANA ◽  
2014 ◽  
Vol 11 ◽  
pp. 131-135 ◽  
Author(s):  
Kabita Jha ◽  
Ajaya Bhattarai ◽  
Sujeet Kumar Chatterjee

NOTE: The correct reference list was added to this article on 08/07/2014.Viscosity measurement of cetyltrimethylammonium bromide in presence and in absence of KCl and NaCl in aqueous media is done. The results showed a sharp increase in viscosity with increase in concentration of cetyltrimethylammonium bromide. Also, the viscosity increases with addition of salts. The viscosity of cetyltrimethylammonium bromide is found more in presence of KCl than NaCl in aqueous media. In presence of monovalent salts, the critical micelle concentration (cmc) value decreases which is explained on the basis of nature and ionic strength of the added ion. The graphs of viscosity versus concentration are used in determining the critical micelle concentration (cmc). DOI: http://dx.doi.org/10.3126/bibechana.v11i0.10392BIBECHANA 11(1) (2014) 131-135


BIBECHANA ◽  
2014 ◽  
Vol 11 ◽  
pp. 103-112 ◽  
Author(s):  
Tulasi Prasad Niraula ◽  
Ajaya Bhattarai ◽  
Sujeet Kumar Chatterjee

Careful measurements of surface tension and viscosity of sodium dodecyl sulphate (SDS) in presence and absence of KCl in pure water and methanol-water mixed solvent media containing 0.1, 0.2, 0.3 and 0.4 volume fractions of methanol at 308.15 K are reported. The concentration of KCl is 0.01M. The concentration of SDS varies from 4.86×10-3 to 29.56×10-3 mol.l-1. The critical micelle concentration (cmc) increases with increase in percentage of methanol and decreases with addition of salt. DOI: http://dx.doi.org/10.3126/bibechana.v11i0.10388 BIBECHANA 11(1) (2014) 103-112


2015 ◽  
Vol 12 (12) ◽  
pp. 41-43 ◽  
Author(s):  
Ajaya Bhattarai ◽  
S K Shah ◽  
Kuber Limbu

Conductance measurement of sodium dodecylsulfate in the presence and in the absence of Na2SO4 and ZnSO4 in aqueous media was done. The results showed sharp increase in conductance with increase in concentration of sodium dodecylsulfate. Also, the conductance increases with addition of salts. The conductance of sodium dodecylsulfate is found more in the presence of Na2SO4 than ZnSO4 in aqueous media. In the presence of salts, the critical micelle concentration (cmc) value decreases which are explained on the basis of the nature and ion size of the added ion. The graph of conductance versus concentration is used in determining the critical micelle concentration (cmc).Scientific World, Vol. 12, No. 12, September 2014, page 41-43        


Author(s):  
P. A. Madden ◽  
W. R. Anderson

The intestinal roundworm of swine is pinkish in color and about the diameter of a lead pencil. Adult worms, taken from parasitized swine, frequently were observed with macroscopic lesions on their cuticule. Those possessing such lesions were rinsed in distilled water, and cylindrical segments of the affected areas were removed. Some of the segments were fixed in buffered formalin before freeze-drying; others were freeze-dried immediately. Initially, specimens were quenched in liquid freon followed by immersion in liquid nitrogen. They were then placed in ampuoles in a freezer at −45C and sublimated by vacuum until dry. After the specimens appeared dry, the freezer was allowed to come to room temperature slowly while the vacuum was maintained. The dried specimens were attached to metal pegs with conductive silver paint and placed in a vacuum evaporator on a rotating tilting stage. They were then coated by evaporating an alloy of 20% palladium and 80% gold to a thickness of approximately 300 A°. The specimens were examined by secondary electron emmission in a scanning electron microscope.


1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


Sign in / Sign up

Export Citation Format

Share Document