scholarly journals RELATIONSHIP BETWEEN DURABILITY AGAINST DYNAMIC LOAD OF RESIN FLOOR COATING AND SURFACE LAYER QUALITY OF SLAB CONCRETE

2021 ◽  
Vol 86 (781) ◽  
pp. 361-370
Author(s):  
Yutaro FUJII ◽  
Hiroki TAKAYAMA ◽  
Shintaro FUKUDA ◽  
Yutaka YOKOYAMA
Keyword(s):  
Surface Layer ◽  
Dynamic Load ◽  
Surface Layer Quality

scholarly journals Rated definition of degree of cutter coating influence upon parameters of surface layer quality of parts worked

2017 ◽  
Vol 2 (7) ◽  
pp. 20-24
Author(s):  
Вячеслав Безъязычный ◽  
Vyacheslav Bezyazychnyy ◽  
Максим Басков ◽  
Maksim Baskov
Keyword(s):  
Surface Roughness ◽  
Surface Layer ◽  
Residual Stresses ◽  
Layer Surface ◽  
Wear Resistant Coatings ◽  
Cutter Wear ◽  
Definition Of ◽  
Surface Layer Quality ◽  
The Impact

The impact of cutter wear-resistant coatings upon cutting process parameters and characteristics of surface layer quality in the parts worked: residual stresses, a degree and a depth of work hardening of a surface layer, surface roughness is investigated.

scholarly journals Problems of Analyzing Microstructure Images in Assessing the Impact of Technological Parameters of Combined Strain Wave Hardening on the Quality of the Surface Layer

2019 ◽  
Author(s):  
Андрей Киричек ◽  
Andrey Kirichek ◽  
Дмитрий Соловьев ◽  
Dmitriy Solovyev ◽  
Александр Хандожко ◽  
...  
Keyword(s):  
Surface Layer ◽  
Thermal Treatment ◽  
Strain Wave ◽  
Technological Parameters ◽  
Steel Microstructure ◽  
Main Indicator ◽  
Metallographic Images ◽  
Surface Layer Quality ◽  
The Impact

The problems of analyzing metallographic images and the method of their solution using modern software for the analysis of metallographic images are described. There is given an analysis of microstructure images as the main indicator of the surface layer quality by the example of studying the research results of strain wave hardening combinations and chemical-thermal treatment, in particular the influence of previous strain wave hardening and subsequent thermal and chemical- thermal treatment on the alloy steel microstructure or previous thermal and chemical- thermal treatment and subsequent strain wave hardening. On the basis of the analysis the effectiveness of strain wave hardening and chemical and thermal treatment is established.

An accelerated method of inspecting the surface-layer quality of parts during machining

1981 ◽  
Vol 17 (1) ◽  
pp. 91-93
Author(s):  
P. A. Rutman ◽  
N. V. Pertsov ◽  
V. S. Lobantsova
Keyword(s):  
Surface Layer ◽  
Surface Layer Quality

scholarly journals Surface layer quality in compressor titanium blades at multiaxes deep grinding

2017 ◽  
Vol 2 (12) ◽  
pp. 15-19
Author(s):  
В. Полетаев ◽  
V. Poletaev ◽  
Е. Цветков ◽  
E. Tsvetko
Keyword(s):  
Titanium Alloy ◽  
Surface Layer ◽  
Residual Stresses ◽  
Gas Turbine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Blade Surface ◽  
A Value ◽  
Surface Layer Quality

The investigation results of technological conditions impact at multiaxes deep grinding upon quality of titanium alloy blade surface layer in the compressors of gas turbine engines (GTE) are presented. The grinding mode impact upon a surface and a value of residual stresses in a surface layer of blades is defined and also conditions for defect occurrence as burns on blade surfaces under machining are detected.

scholarly journals Evaluation of conventional standards of nickel electroplating process for surface finish layer of AISI 316L stainless steel using copper rod bars as cathode

2018 ◽  
Vol 49 ◽  
pp. 02002
Author(s):  
Patrick Munyensanga ◽  
Susilo A. Widyanto ◽  
Moh N.A. Aziz ◽  
Paryanto
Keyword(s):  
Stainless Steel ◽  
Surface Layer ◽  
Surface Finish ◽  
Surface Cleaning ◽  
Aisi 316L ◽  
Nickel Electroplating ◽  
Time Required ◽  
Electroplating Process ◽  
Surface Layer Quality

Nickel electroplating process at UD Barito Electroplating is a modern methodology installed in an open complex environment and at controlled temperature with trust consideration of specimen composition. The evaluation of process at UD Barito has been undertaken by considering Stainless steel AISI 316L as specimen through a conventional nickel electroplating process. This paper presents the proper scientifically tool to be used at UD Barito in order to meet the time required and the surface layer quality of the electroplated product. The use of ultrasonic to replace air compressor assembly does not cause any harm to the surface finish smoothness and the quality of plated specimen given that the process is conventional. Concerning the process of 10 min compared up to 15 min of the process at UD Barito; showed the facility of ultrasonic assisted the electroplating process. This process is also a useful method in maintenance activities for surface cleaning and for product surface-layer quality enhancement through the coating process. From the data analyzed, the specimen has a hydrogen embrittlement rate range between 20 to 65% of Rockwell scale HRC52.

scholarly journals Formation features of structure, performance properties and surface layer quality of 3KH2V8F die steel tooling

2019 ◽  
Vol 23 (6) ◽  
pp. 1104-1115
Author(s):  
Nikolay Ulakhanov ◽  
◽  
Undrakh Mishigdorzhiyn ◽  
Anatoly Greshilov ◽  
Alexander Tikhonov ◽  
...  
Keyword(s):  
Surface Layer ◽  
Performance Properties ◽  
Die Steel ◽  
Surface Layer Quality

Technological quality assurance of the surface layer and operational properties of machine parts by electroerosion treatment

2021 ◽  
Vol 2021 (11) ◽  
pp. 30-37
Author(s):  
Sergey S'yanov
Keyword(s):  
Wear Resistance ◽  
Surface Layer ◽  
Corrosion Rate ◽  
Endurance Limit ◽  
Mechanical Parameters ◽  
Technological Support ◽  
Technological Quality ◽  
Machine Parts ◽  
Surface Layer Quality

Dependences for determining geometric, physical and mechanical parameters of the surface layer quality, wear resistance, corrosion rate and endurance limit depending on the modes and conditions of electroerosion treatment of machine parts have been given. These dependences allow determining optimal modes and conditions of electroerosion treatment to ensure the required parameters of the quality of the surface layer (with a two–stage approach - design and technological support of operational properties), wear resistance, corrosion rate and endurance limit (with a single-stage approach - direct technological support).

Sign in / Sign up

Export Citation Format

Share Document