scholarly journals Inertial Parameter Identification in Robotics: A Survey

2021 ◽  
Vol 11 (9) ◽  
pp. 4303
Author(s):  
Quentin Leboutet ◽  
Julien Roux ◽  
Alexandre Janot ◽  
Julio Rogelio Guadarrama-Olvera ◽  
Gordon Cheng
Keyword(s):  
Neural Network ◽  
Parameter Identification ◽  
Closed Loop ◽  
Dynamic Models ◽  
Robot Dynamics ◽  
Dynamic Identification ◽  
Inverse Dynamic ◽  
Inertial Parameter ◽  
Serial Robot ◽  
Identification Model

This work aims at reviewing, analyzing and comparing a range of state-of-the-art approaches to inertial parameter identification in the context of robotics. We introduce “BIRDy (Benchmark for Identification of Robot Dynamics)”, an open-source Matlab toolbox, allowing a systematic and formal performance assessment of the considered identification algorithms on either simulated or real serial robot manipulators. Seventeen of the most widely used approaches found in the scientific literature are implemented and compared to each other, namely: the Inverse Dynamic Identification Model with Ordinary, Weighted, Iteratively Reweighted and Total Least-Squares (IDIM-OLS, -WLS, -IRLS, -TLS); the Instrumental Variables method (IDIM-IV), the Maximum Likelihood (ML) method; the Direct and Inverse Dynamic Identification Model approach (DIDIM); the Closed-Loop Output Error (CLOE) method; the Closed-Loop Input Error (CLIE) method; the Direct Dynamic Identification Model with Nonlinear Kalman Filtering (DDIM-NKF), the Adaline Neural Network (AdaNN), the Hopfield-Tank Recurrent Neural Network (HTRNN) and eventually a set of Physically Consistent (PC-) methods allowing the enforcement of parameter physicality using Semi-Definite Programming, namely the PC-IDIM-OLS, -WLS, -IRLS, PC-IDIM-IV, and PC-DIDIM. BIRDy is robot-agnostic and features a complete inertial parameter identification pipeline, from the generation of symbolic kinematic and dynamic models to the identification process itself. This includes functionalities for excitation trajectory computation as well as the collection and pre-processing of experiment data. In this work, the proposed methods are first evaluated in simulation, following a Monte Carlo scheme on models of the 6-DoF TX40 and RV2SQ industrial manipulators, before being tested on the real robot platforms. The robustness, precision, computational efficiency and context of application the different methods are investigated and discussed.

scholarly journals Dynamic Parameter Identification of Overactuated Parallel Robots

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Sébastien Briot ◽  
Sébastien Krut ◽  
Maxime Gautier
Keyword(s):  
Parameter Identification ◽  
A Priori ◽  
Dynamic Parameter ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Current Loop ◽  
Dynamic Identification ◽  
Inverse Dynamic ◽  
Identification Process ◽  
Dynamic Parameter Identification

Offline robot dynamic identification methods are based on the use of the inverse dynamic identification model (IDIM), which calculates the joint forces/torques (estimated as the product of the known control signal (the input reference of the motor current loop) with the joint drive gains) that are linear in relation to the dynamic parameters, and on the use of the linear least squares technique to calculate the parameters (IDIM-LS technique). However, as actuation-redundant parallel robots are overactuated, their IDIM has an infinity of solution for the force/torque prediction, depending on the value of the desired overconstraint that is a priori unknown in the identification process. As a result, the IDIM cannot be used as it is for such a class of parallel robots. This paper proposes a procedure for the dynamic parameter identification of actuation-redundant parallel robots. The procedure takes advantage of two possible modified formulations for the IDIM of actuation-redundant robots that can be used for identification purpose. The modified IDIM formulations project some or all input torques/forces onto the robot bodies, thus leading to a unique solution of the model that can then be used in the identification process. A systematic and straightforward way to compute these modified IDIM is presented. The identification of the inertial parameters of a planar parallel robot with actuation redundancy, the DualV, is then carried out using these modified IDIM. Experimental results show the validity of the methods.

scholarly journals A New Closed-Loop Output Error Method for Parameter Identification of Robot Dynamics

2013 ◽  
Vol 21 (2) ◽  
pp. 428-444 ◽  
Author(s):  
Maxime Gautier ◽  
Alexandre Janot ◽  
Pierre-Olivier Vandanjon
Keyword(s):  
Parameter Identification ◽  
Closed Loop ◽  
Robot Dynamics ◽  
Output Error ◽  
Error Method

Intelligent Dynamic Roughness Identification Model in Grinding

2011 ◽  
Vol 48-49 ◽  
pp. 621-624
Author(s):  
Ning Ding ◽  
Ding Tong Zhang ◽  
Ye He
Keyword(s):  
Neural Network ◽  
Surface Roughness ◽  
Fuzzy Neural Network ◽  
Vibration Signal ◽  
Dynamic Identification ◽  
Grinding Parameters ◽  
Proposed Model ◽  
Fuzzy Neural ◽  
External Cylindrical Grinding ◽  
Identification Model

In this paper, first, the relation between roughness and grinding parameters is built. Then, an intelligent dynamic identification model of surface roughness is developed, which bases on the theory of roughness during grinding and the theory of fuzzy-neural network. The inputs for the model are the grinding parameters. Besides, an accelerometer is used to gather the dynamic vibration signal in real time. The model was used in the external cylindrical grinding experiment, and the result verified that the proposed model was feasible.

scholarly journals Comparative Analysis of Identification Methods for Mechanical Dynamics of Large-Scale Wind Turbine

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3429 ◽  
Author(s):  
Chu ◽  
Yuan ◽  
Hu ◽  
Pan ◽  
Pan
Keyword(s):  
Mutual Information ◽  
Parameter Identification ◽  
Wind Turbines ◽  
Closed Loop ◽  
Control Design ◽  
Identification Accuracy ◽  
Mass Model ◽  
Identification Methods ◽  
Advanced Control ◽  
Mechanical Dynamics

With increasing size and flexibility of modern grid-connected wind turbines, advanced control algorithms are urgently needed, especially for multi-degree-of-freedom control of blade pitches and sizable rotor. However, complex dynamics of wind turbines are difficult to be modeled in a simplified state-space form for advanced control design considering stability. In this paper, grey-box parameter identification of critical mechanical models is systematically studied without excitation experiment, and applicabilities of different methods are compared from views of control design. Firstly, through mechanism analysis, the Hammerstein structure is adopted for mechanical-side modeling of wind turbines. Under closed-loop control across the whole wind speed range, structural identifiability of the drive-train model is analyzed in qualitation. Then, mutual information calculation among identified variables is used to quantitatively reveal the relationship between identification accuracy and variables’ relevance. Then, the methods such as subspace identification, recursive least square identification and optimal identification are compared for a two-mass model and tower model. At last, through the high-fidelity simulation demo of a 2 MW wind turbine in the GH Bladed software, multivariable datasets are produced for studying. The results show that the Hammerstein structure is effective for simplify the modeling process where closed-loop identification of a two-mass model without excitation experiment is feasible. Meanwhile, it is found that variables’ relevance has obvious influence on identification accuracy where mutual information is a good indicator. Higher mutual information often yields better accuracy. Additionally, three identification methods have diverse performance levels, showing their application potentials for different control design algorithms. In contrast, grey-box optimal parameter identification is the most promising for advanced control design considering stability, although its simplified representation of complex mechanical dynamics needs additional dynamic compensation which will be studied in future.

scholarly journals Predicting the Energy Consumption of a Robot in an Exploration Task Using Optimized Neural Networks

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 920
Author(s):  
Liesle Caballero ◽  
Álvaro Perafan ◽  
Martha Rinaldy ◽  
Winston Percybrooks
Keyword(s):  
Neural Network ◽  
Energy Consumption ◽  
Mobile Robot ◽  
Energy Budget ◽  
Dynamic Models ◽  
Pearson Correlation ◽  
Experimental Conditions ◽  
Grid Map ◽  
Proposed Model ◽  
Exploration Task

This paper deals with the problem of determining a useful energy budget for a mobile robot in a given environment without having to carry out experimental measures for every possible exploration task. The proposed solution uses machine learning models trained on a subset of possible exploration tasks but able to make predictions on untested scenarios. Additionally, the proposed model does not use any kinematic or dynamic models of the robot, which are not always available. The method is based on a neural network with hyperparameter optimization to improve performance. Tabu List optimization strategy is used to determine the hyperparameter values (number of layers and number of neurons per layer) that minimize the percentage relative absolute error (%RAE) while maximize the Pearson correlation coefficient (R) between predicted data and actual data measured under a number of experimental conditions. Once the optimized artificial neural network is trained, it can be used to predict the performance of an exploration algorithm on arbitrary variations of a grid map scenario. Based on such prediction, it is possible to know the energy needed for the robot to complete the exploration task. A total of 128 tests were carried out using a robot executing two exploration algorithms in a grid map with the objective of locating a target whose location is not known a priori by the robot. The experimental energy consumption was measured and compared with the prediction of our model. A success rate of 96.093% was obtained, measured as the percentage of tests where the energy budget suggested by the model was enough to actually carry out the task when compared to the actual energy consumed in the test, suggesting that the proposed model could be useful for energy budgeting in actual mobile robot applications.

The parameter identification model considering both geometric parameters and joint stiffness

2019 ◽  
Vol 47 (1) ◽  
pp. 76-81
Author(s):  
Jing Bai ◽  
Le Fan ◽  
Shuyang Zhang ◽  
Zengcui Wang ◽  
Xiansheng Qin
Keyword(s):  
Parameter Identification ◽  
Industrial Robot ◽  
Joint Stiffness ◽  
Geometric Parameters ◽  
Least Square ◽  
Experimental Result ◽  
Positional Accuracy ◽  
Content Type ◽  
The Absolute ◽  
Identification Model

Purpose Both geometric and non-geometric parameters have noticeable influence on the absolute positional accuracy of 6-dof articulated industrial robot. This paper aims to enhance it and improve the applicability in the field of flexible assembling processing and parts fabrication by developing a more practical parameter identification model. Design/methodology/approach The model is developed by considering both geometric parameters and joint stiffness; geometric parameters contain 27 parameters and the parallelism problem between axes 2 and 3 is involved by introducing a new parameter. The joint stiffness, as the non-geometric parameter considered in this paper, is considered by regarding the industrial robot as a rigid linkage and flexible joint model and adds six parameters. The model is formulated as the form of error via linearization. Findings The performance of the proposed model is validated by an experiment which is developed on KUKA KR500-3 robot. An experiment is implemented by measuring 20 positions in the work space of this robot, obtaining least-square solution of measured positions by the software MATLAB and comparing the result with the solution without considering joint stiffness. It illustrates that the identification model considering both joint stiffness and geometric parameters can modify the theoretical position of robots more accurately, where the error is within 0.5 mm in this case, and the volatility is also reduced. Originality/value A new parameter identification model is proposed and verified. According to the experimental result, the absolute positional accuracy can be remarkably enhanced and the stability of the results can be improved, which provide more accurate parameter identification for calibration and further application.

Sign in / Sign up

Export Citation Format

Share Document