scholarly journals Flexural Behavior of UHPC Beams Prestressed with External CFRP Tendons

2021 ◽  
Vol 11 (19) ◽  
pp. 9189
Author(s):  
Li Jia ◽  
Zhi Fang ◽  
Zhengmeng Huang ◽  
Kypros Pilakoutas ◽  
Qiwu Wang ◽  
...  
Keyword(s):  
High Performance ◽  
Loading Condition ◽  
High Performance Concrete ◽  
High Strength ◽  
Shear Capacity ◽  
Utilization Efficiency ◽  
Flexural Behavior ◽  
Flexural Capacity ◽  
Deformation Ability ◽  
Prestressed Beams

This paper presents an experimental investigation on the flexural behavior of ultra-high-performance concrete (UHPC) beams prestressed with external carbon fiber-reinforced polymer (CFRP) tendons. A total of eight T-shaped beam specimens were fabricated and tested, and the effects of the effective prestressing stress, partial prestressing ratio, deviated angle, and loading condition on the flexural behavior were analyzed. The experimental results indicate that the fully prestressed beams experienced a brittle failure, and the shear capacity of these beams was mainly controlled by the effective prestressing stress in CFRP tendons and the ultimate tensile strength of UHPC, whereas the partially prestressed beams failed in a ductile manner. The presence of internal steel reinforcement could significantly improve the flexural capacity and deformation ability. Thus, internal reinforcements should not be omitted from UHPC beams with CFRP tendons. A higher effective prestressing stress resulted in enhanced cracking load and flexural capacity. The deviated angle enhanced the utilization efficiency of high strength CFRP tendons. The loading condition exerted a slight influence on the flexural behavior of the specimens. Moreover, a method considering the effect of steel fibers was proposed and verified to predict the flexural capacity of UHPC beams prestressed with external CFRP tendons.

scholarly journals Flexural Behavior Performance of Reinforced Concrete Slabs Mixed with Nano- and Microsilica

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Rakesh Kancharla ◽  
Venkata Rao Maddumala ◽  
T. V. N. Prasanna ◽  
Lokaiah Pullagura ◽  
Ratna Raju Mukiri ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Flexural Behavior ◽  
Concrete Slabs ◽  
The Past ◽  
Reinforced Concrete Slabs ◽  
Concrete Mix ◽  
Bending Behavior

Present technology has been evaluated greatly over the past decades, where new particles are being designed and fabricated to fulfill specific needs. The field of nano- and micromaterials has prospered in many disciplines. It has been recently used in reinforced concrete in the production of high-strength, high-performance concrete. Microsilica (MS) and nanosilica (NS) particles have proven to be highly profitable to the concrete mix. Concrete has become denser with considerable improvement in their mechanical characteristics, particularly compressive strength. This proposed method includes a comparative study of the flexural bending behavior of conventional reinforced concrete (without MS or NS) slabs with other slabs. Each has various mixes of MS and NS particles incorporated into the concrete mix. The material content utilized in the slabs is kept constant by replacing a portion of the cement with an equivalent amount of either NS or MS particles or both. MS particles are altered from 0, 5, and 10% while NS particles are altered from 0, 0.5, and 1.0%. It cracks the widths and has higher final load-bearing capacity.

scholarly journals Experimental Investigation of Flexural Behavior of Ultra-High-Performance Concrete with Coarse Aggregate-Filled Steel Tubes

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6354
Author(s):  
Fanghong Wu ◽  
Yanqin Zeng ◽  
Ben Li ◽  
Xuetao Lyu
Keyword(s):  
Experimental Investigation ◽  
High Performance ◽  
Coarse Aggregate ◽  
High Performance Concrete ◽  
Steel Tube ◽  
Flexural Behavior ◽  
Flexural Stiffness ◽  
Flexural Capacity ◽  
Ultra High Performance Concrete ◽  
Steel Tubes

This paper presents an experimental investigation of flexural behavior of circular ultra-high-performance concrete with coarse aggregate (CA-UHPC)-filled steel tubes (CA-UHPCFSTs). A total of seven flexural members were tested under a four-point bending load. The failure modes, overall deflection curves, moment-versus-curvature relationships, moment-versus-strain curves, strain distribution curves, ductility, flexural stiffness and ultimate flexural capacity were evaluated. The results indicate that the CA-UHPCFSTs under bending behaved in a good ductile manner. The CA-UHPC strength has a limited effect on the ultimate flexural capacity, while the addition of steel fiber can improve the ultimate flexural capacity. Increasing the steel tube thickness leads to higher flexural stiffness and ultimate flexural capacity. There is a significant confinement effect between the steel tube and the CA-UHPC core in the compressive zone and centroidal plane after the specimen enters the elastic-plastic stage, while the confinement effect in the tensile zone is minimal. Moreover, the measured flexural stiffness and ultimate flexural capacity were compared with the predictions using various design specifications. Two empirical formulas for calculating the initial and serviceability-level flexural stiffness of CA-UHPCFSTs are developed. Further research is required to propose the accurate design formula for the ultimate flexural capacity of CA-UHPCFSTs.

Bestimmung der Dauerhaftigkeit von Hochleistungsbeton mit Hilfe des CDF-Tests / Determination of the durability of high performance concrete by means of CDF-test

1999 ◽  
Vol 5 (1) ◽  
pp. 29-40
Author(s):  
R. Krumbach ◽  
U. Schmelter ◽  
K. Seyfarth
Keyword(s):  
Frost Resistance ◽  
High Strength Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Strength Concrete ◽  
Factors Influencing

Abstract Variable obsen>ations concerning frost resistance of high performance concrete have been made. The question arises which are the decisive factors influencing durability under the action of frost and de-icing salt. The proposed experiments are to be carried out in cooperation with F.A.- Finger - Institute of Bauhaus University Weimar. The aim of this study is to determine possible change of durability of high strength concrete, and to investigate the origin thereof. Measures to reduce the risk of reduced durability have to be found.

scholarly journals Hugoniot Data and Equation of State Parameters for an Ultra-High Performance Concrete

2021 ◽  
Author(s):  
C. Sauer ◽  
F. Bagusat ◽  
M.-L. Ruiz-Ripoll ◽  
C. Roller ◽  
M. Sauer ◽  
...  
Keyword(s):  
Equation Of State ◽  
High Performance ◽  
High Performance Concrete ◽  
Applied Pressure ◽  
High Strength ◽  
Parameter Study ◽  
Ultra High Performance Concrete ◽  
Data Set ◽  
Shock Response ◽  
Particle Velocities

AbstractThis work aims at the characterization of a modern concrete material. For this purpose, we perform two experimental series of inverse planar plate impact (PPI) tests with the ultra-high performance concrete B4Q, using two different witness plate materials. Hugoniot data in the range of particle velocities from 180 to 840 m/s and stresses from 1.1 to 7.5 GPa is derived from both series. Within the experimental accuracy, they can be seen as one consistent data set. Moreover, we conduct corresponding numerical simulations and find a reasonably good agreement between simulated and experimentally obtained curves. From the simulated curves, we derive numerical Hugoniot results that serve as a homogenized, mean shock response of B4Q and add further consistency to the data set. Additionally, the comparison of simulated and experimentally determined results allows us to identify experimental outliers. Furthermore, we perform a parameter study which shows that a significant influence of the applied pressure dependent strength model on the derived equation of state (EOS) parameters is unlikely. In order to compare the current results to our own partially reevaluated previous work and selected recent results from literature, we use simulations to numerically extrapolate the Hugoniot results. Considering their inhomogeneous nature, a consistent picture emerges for the shock response of the discussed concrete and high-strength mortar materials. Hugoniot results from this and earlier work are presented for further comparisons. In addition, a full parameter set for B4Q, including validated EOS parameters, is provided for the application in simulations of impact and blast scenarios.

scholarly journals Abrasion Resistance of Ultra-High-Performance Concrete for Railway Sleepers

2021 ◽  
Author(s):  
Ariful Hasnat ◽  
Nader Ghafoori
Keyword(s):  
Prestressed Concrete ◽  
Abrasion Resistance ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Positive Influence ◽  
Cementitious Material ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Ultra High Performance Concrete

AbstractThis study aimed to determine the abrasion resistance of ultra-high-performance concretes (UHPCs) for railway sleepers. Test samples were made with different cementitious material combinations and varying steel fiber contents and shapes, using conventional fine aggregate. A total of 25 UHPCs and two high-strength concretes (HSCs) were selected to evaluate their depth of wear and bulk properties. The results of the coefficient of variation (CV), relative gain in abrasion, and abrasion index of the studied UHPCs were also obtained and discussed. Furthermore, a comparison was made on the resistance to wear of the selected UHPCs with those of the HSCs typically used for prestressed concrete sleepers. The outcomes of this study revealed that UHPCs displayed excellent resistance against abrasion, well above that of HSCs. Amongst the utilized cementitious material combinations, UHPCs made with silica fume as a partial replacement of cement performed best against abrasion, whereas mixtures containing fly ash showed the highest depth of wear. The addition of steel fibers had a more positive influence on the abrasion resistance than it did on compressive strength of the studied UHPCs.

Accelerated testing of super lightweight UHPC waffle deck under heavy vehicle simulator

2021 ◽  
Vol 16 (2-3) ◽  
pp. 61-74
Author(s):  
Sahar Ghasemi ◽  
Amir Mirmiran ◽  
Yulin Xiao ◽  
Kevin Mackie
Keyword(s):  
High Performance ◽  
Failure Modes ◽  
High Performance Concrete ◽  
High Strength ◽  
Heavy Vehicle ◽  
Wheel Load ◽  
Element Analysis ◽  
Vehicle Simulator ◽  
Pavement Testing ◽  
Heavy Vehicle Simulator

A super lightweight deck can enhance load rating and functionality of a bridge, especially those identified as structurally deficient. This study was aimed to develop and experimentally validate a novel bridge deck as an ultra-lightweight low-profile waffle slab of ultra-high-performance concrete (UHPC) with either carbon fiber reinforced polymer (CFRP) or high strength steel (HSS) reinforcement. The proposed system lends itself to accelerated bridge construction, rapid deck replacement in bridges with load restrictions, and bridge widening applications without the need to replace girders. Performance and failure modes of the proposed deck were initially assessed through extensive lab experiments and finite element analysis, which together confirmed that the proposed deck panel meets the AASHTO LRFD requirements. The proposed deck system is not susceptible to punching shear of its thin slab and fails in a rather ductile manner. To evaluate its long-term performance, the system was further tested under the dynamic impact of wheel load at the Accelerated Pavement Testing (APT) facility of the Florida Department of Transportation using a Heavy Vehicle Simulator (HVS).

scholarly journals Resistance of an Optimized Ultra-High Performance Fiber Reinforced Concrete to Projectile Impact

Buildings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 63
Author(s):  
Anna L. Mina ◽  
Michael F. Petrou ◽  
Konstantinos G. Trezos
Keyword(s):  
Reinforced Concrete ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Depth Of Penetration ◽  
Projectile Impact ◽  
High Performance Fiber

The scope of this paper is to investigate the performance of ultra-high performance fiber reinforced concrete (UHPFRC) concrete slabs, under projectile impact. Mixture performance under impact loading was examined using bullets with 7.62 mm diameter and initial velocity 800 m/s. The UHPFRC, used in this study, consists of a combination of steel fibers of two lengths: 6 mm and 13 mm with the same diameter of 0.16 mm. Six composition mixtures were tested, four UHPFRC, one ultra-high performance concrete (UHPC), without steel fibers, and high strength concrete (HSC). Slabs with thicknesses of 15, 30, 50, and 70 mm were produced and subjected to real shotgun fire in the field. Penetration depth, material volume loss, and crater diameter were measured and analyzed. The test results show that the mixture with a combination of 3% 6 mm and 3% of 13 mm length of steel fibers exhibited the best resistance to projectile impact and only the slabs with 15 mm thickness had perforation. Empirical models that predict the depth of penetration were compared with the experimental results. This material can be used as an overlay to buildings or to construct small precast structures.

Sign in / Sign up

Export Citation Format

Share Document