scholarly journals Review of Process Modeling of Solid-Fuel Thermal Power Plants for Flexible and Off-Design Operation

Energies ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 6587
Author(s):  
Ioannis Avagianos ◽  
Dimitrios Rakopoulos ◽  
Sotirios Karellas ◽  
Emmanouil Kakaras
Keyword(s):  
Solid Fuel ◽  
Process Modeling ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Power Production ◽  
Operating Conditions ◽  
Thermal Power Plants ◽  
Modeling Tools ◽  
Flexible Operation

Since the widespread deployment of non-dispatchable, intermittent, and highly variable power production from renewable energy sources (RES), the demand for flexible power production has been steadily growing. As new-built dispatchable power plants have not been very quickly adapted to the emerging flexible operation, this task has been addressed by existing plants as well. Existing solid-fuel thermal power plants have undergone an extensive study to increase their flexible operation. Thermodynamic process-modeling tools have been extensively used for plant modeling. Steady- and transient-state simulations have been performed under various operating regimes, supplying valuable results for efficient power-plant operation. Flexibility aspects regarding low-load operation and steady operational conditions are mostly investigated with steady-state simulations. Flexibility aspects related to variation over time such as ramping rates are investigated with transient simulations. The off-design operation is mainly attributed to the existing fleet of power plants, struggling to balance between their former operational schemes as base and/or medium-load plants. However, off-design operation is also considered for new plants in the design phase and is included as a simulation aspect. Process modeling turns out to be a proven tool for calculating plant flexibility and predicting extreme operating conditions, defining further steps for a new operational scheme, drafting accident mitigation control procedures or, furthermore, provisioning more complex and cross-field future tasks. A review of the off-design aspect as a simulation approach is undertaken and presented in this work. Finally, challenges and future perspectives for this aspect of solid-fuel thermal power plants are discussed.

On the prospect of introduction of plasma ignition in power boilers

2019 ◽  
Vol 12 (1) ◽  
pp. 22-28
Author(s):  
V. Ye. Mikhailov ◽  
S. P. Kolpakov ◽  
L. A. Khomenok ◽  
N. S. Shestakov
Keyword(s):  
Russian Federation ◽  
Solid Fuel ◽  
Power Plants ◽  
Thermal Power ◽  
Fuel Oil ◽  
Solid Fuels ◽  
Thermal Power Plants ◽  
Plasma Ignition ◽  
The Russian Federation ◽  
Capital Construction

One of the most important issues for modern domestic power industry is the creation and further widespread introduction of solid propellant energy units for super-critical steam parameters with high efficiency (43–46%) and improved environmental parameters. This will significantly reduce the use of natural gas.At the same time, one of the major drawbacks of the operation of pulverized coal power units is the need to use a significant amount of fuel oil during start-up and shutdown of boilers to stabilize the burning of the coal torch in the variable boiler operating modes.In this regard, solid fuel TPPs need to be provided with fuel oil facilities, with all the associated problems to ensure the performance (heating of fuel oil in winter), reliability and safety. All of the above problems increase both the TPP capital construction costs, and the electricity generating cost.A practical solution to the above problems at present is the use of a plasma technology for coal torch ignition based on thermochemical preparation of fuel for combustion. The materials of the developments of JSC “NPO CKTI” on application of plasmatrons in boilers of thermal power plants at metallurgical complexes of the Russian Federation are also considered.Plasma ignition systems for solid fuels in boilers were developed by Russian specialists and were introduced at a number of coal-fi red power plants in the Russian Federation, Mongolia, North Korea, and Kazakhstan. Plasma ignition of solid fuels is widely used in China for almost 30% of power boilers.The introduction of plasma-energy technologies will improve the energy efficiency of domestic solid-fuel thermal power plants and can be widely implemented in the modernization of boilers.During the construction of new TPPs, the construction of fuel oil facilities can be abandoned altogether, which will reduce the capital costs of the construction of thermal power plants, reduce the construction footprint, and increase the TPP safety.

scholarly journals Selection of Heat Pump Capacity Used at Thermal Power Plants under Electricity Market Operating Conditions

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 226
Author(s):  
Milana Treshcheva ◽  
Irina Anikina ◽  
Vitaly Sergeev ◽  
Sergey Skulkin ◽  
Dmitry Treshchev
Keyword(s):  
Electric Power ◽  
Heat Pump ◽  
Heat Load ◽  
Power Plants ◽  
Thermal Power ◽  
Heat Pumps ◽  
Operating Conditions ◽  
Energy Resources ◽  
Thermal Power Plants ◽  
Maximum Heat

The percentage of heat pumps used in thermal power plants (TPPs) in the fuel and energy balance is extremely low in in most countries. One of the reasons for this is the lack of a systematic approach to selecting and justifying the circuit solutions and equipment capacity. This article aims to develop a new method of calculating the maximum capacity of heat pumps. The method proposed in the article has elements of marginal analysis. It takes into account the limitation of heat pump capacity by break-even operation at electric power market (compensation of fuel expenses, connected with electric power production). In this case, the heat pump’s maximum allowable capacity depends on the electric capacity of TPP, electricity consumption for own needs, specific consumption of conditional fuel for electricity production, a ratio of prices for energy resources, and a conversion factor of heat pump. For TPP based on combined cycle gas turbine (CCGT) CCGT-450 with prices at the Russian energy resources markets at the level of 2019, when operating with the maximum heat load, the allowable heat pump capacity will be about 50 MW, and when operating with the minimum heat load—about 200 MW.

Power Cycles of Generation III and III+ Nuclear Power Plants

2014 ◽  
Author(s):  
Alexey Dragunov ◽  
Eugene Saltanov ◽  
Igor Pioro ◽  
Pavel Kirillov ◽  
Romney Duffey
Keyword(s):  
Renewable Energy ◽  
Natural Gas ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Electrical Energy ◽  
Energy Sources ◽  
Thermal Power Plants

It is well known that the electrical-power generation is the key factor for advances in any other industries, agriculture and level of living. In general, electrical energy can be generated by: 1) non-renewable-energy sources such as coal, natural gas, oil, and nuclear; and 2) renewable-energy sources such as hydro, wind, solar, biomass, geothermal and marine. However, the main sources for electrical-energy generation are: 1) thermal - primary coal and secondary natural gas; 2) “large” hydro and 3) nuclear. The rest of the energy sources might have visible impact just in some countries. Modern advanced thermal power plants have reached very high thermal efficiencies (55–62%). In spite of that they are still the largest emitters of carbon dioxide into atmosphere. Due to that, reliable non-fossil-fuel energy generation, such as nuclear power, becomes more and more attractive. However, current Nuclear Power Plants (NPPs) are way behind by thermal efficiency (30–42%) compared to that of advanced thermal power plants. Therefore, it is important to consider various ways to enhance thermal efficiency of NPPs. The paper presents comparison of thermodynamic cycles and layouts of modern NPPs and discusses ways to improve their thermal efficiencies.

scholarly journals Assessment of efficiency and prospects for the use of hybrid thermal low-capacity power plants in the Republic of Vietnam

2019 ◽  
Vol 124 ◽  
pp. 01040 ◽  
Author(s):  
D. T. Nguen ◽  
D. N. Pham ◽  
G. R. Mingaleeva ◽  
O. V. Afanaseva ◽  
P. Zunino
Keyword(s):  
Power Plants ◽  
Fossil Fuels ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Climatic Conditions ◽  
Energy Sources ◽  
Thermal Power Plants ◽  
Basic Design ◽  
Air Heating ◽  
The Republic

The growing demand for energy and fossil fuels creates increased number of difficulties, while renewable energy sources are still rarely used worldwide, particularly in Vietnam. In this article hybrid thermal power plants based on gas turbine plants are discussed, the increased efficiency of which is achieved by air heating after the compressor in solar air heaters. The basic design equations and the results of evaluating the efficiency and fuel consumption are presented for two thermal power plants of 4.6 MW and 11.8 MW. The dependence of the results on the intensity of solar extraction for the climatic conditions of the Ninh Thuan province of the Republic of Vietnam is discussed.

scholarly journals Optimal Sizing of Battery-Integrated Hybrid Renewable Energy Sources with Ramp Rate Limitations on a Grid Using ALA-QPSO

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5368
Author(s):  
Ramakrishna S. S. Nuvvula ◽  
Devaraj Elangovan ◽  
Kishore Srinivasa Teegala ◽  
Rajvikram Madurai Elavarasan ◽  
Md. Rabiul Islam ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Energy Systems ◽  
Energy Sources ◽  
Thermal Power Plants ◽  
Wind Energy Systems ◽  
Hybrid Renewable Energy ◽  
Optimal Set

Higher penetration of variable renewable energy sources into the grid brings down the plant load factor of thermal power plants. However, during sudden changes in load, the thermal power plants support the grid, though at higher ramping rates and with inefficient operation. Hence, further renewable additions must be backed by battery energy storage systems to limit the ramping rate of a thermal power plant and to avoid deploying diesel generators. In this paper, battery-integrated renewable energy systems that include floating solar, bifacial rooftop, and wind energy systems are evaluated for a designated smart city in India to reduce ramping support by a thermal power plant. Two variants of adaptive-local-attractor-based quantum-behaved particle swarm optimization (ALA-QPSO) are applied for optimal sizing of battery-integrated and hybrid renewable energy sources to minimize the levelized cost of energy (LCoE), battery life cycle loss (LCL), and loss of power supply probability (LPSP). The obtained results are then compared with four variants of differential evolution. The results show that out of 427 MW of the energy potential, an optimal set of hybrid renewable energy sources containing 274 MW of rooftop PV, 99 MW of floating PV, and 60 MW of wind energy systems supported by 131 MWh of batteries results in an LPSP of 0.005%, an LCoE of 0.077 USD/kW, and an LCL of 0.0087. A sensitivity analysis of the results obtained through ALA-QPSO is performed to assess the impact of damage to batteries and unplanned load appreciation, and it is found that the optimal set results in more energy sustainability.

scholarly journals Concentrating solar thermal power

2013 ◽  
Vol 371 (1996) ◽  
pp. 20110433 ◽  
Author(s):  
Hans Müller-Steinhagen
Keyword(s):  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Operating Experience ◽  
Solar Thermal ◽  
Operational Experience ◽  
Thermal Power Plants ◽  
Planning Stage ◽  
Solar Thermal Power ◽  
Advanced Planning

In addition to wind and photovoltaic power, concentrating solar thermal power (CSP) will make a major contribution to electricity provision from renewable energies. Drawing on almost 30 years of operational experience in the multi-megawatt range, CSP is now a proven technology with a reliable cost and performance record. In conjunction with thermal energy storage, electricity can be provided according to demand. To date, solar thermal power plants with a total capacity of 1.3 GW are in operation worldwide, with an additional 2.3 GW under construction and 31.7 GW in advanced planning stage. Depending on the concentration factors, temperatures up to 1000 ° C can be reached to produce saturated or superheated steam for steam turbine cycles or compressed hot gas for gas turbine cycles. The heat rejected from these thermodynamic cycles can be used for sea water desalination, process heat and centralized provision of chilled water. While electricity generation from CSP plants is still more expensive than from wind turbines or photovoltaic panels, its independence from fluctuations and daily variation of wind speed and solar radiation provides it with a higher value. To become competitive with mid-load electricity from conventional power plants within the next 10–15 years, mass production of components, increased plant size and planning/operating experience will be accompanied by technological innovations. On 30 October 2009, a number of major industrial companies joined forces to establish the so-called DESERTEC Industry Initiative, which aims at providing by 2050 15 per cent of European electricity from renewable energy sources in North Africa, while at the same time securing energy, water, income and employment for this region. Solar thermal power plants are in the heart of this concept.

Sign in / Sign up

Export Citation Format

Share Document