scholarly journals Prediction of Stirling-Cycle-Based Heat Pump Performance and Environmental Footprint with Exergy Analysis and LCA

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8478
Author(s):  
Umara Khan ◽  
Ron Zevenhoven ◽  
Lydia Stougie ◽  
Tor-Martin Tveit
Keyword(s):  
Life Cycle ◽  
High Temperature ◽  
Heat Pump ◽  
High Performance ◽  
Exergy Analysis ◽  
Waste Heat ◽  
Heat Pumps ◽  
Fuel Oil ◽  
Environmental Footprint ◽  
Stirling Cycle

The use of Stirling-cycle-based heat pumps in high-temperature applications and waste heat recovery at an industrial scale is of increasing interest due to the promising role in producing thermal energy with zero CO2 emissions. This paper analyzes one such technology as developed by Olvondo Technology and installed at the pharmaceutical company AstraZeneca in Sweden. In this application, the heat pump used roughly equal amounts of waste heat and electricity and generated 500 kW of steam at 10 bar. To develop and widen the use of a high-performance high-temperature heat pump that is both economically and environmentally viable and attractive, various analysis tools such as exergy analysis and life cycle assessment (LCA) can be combined. The total cumulative exergy loss (TCExL) method used in this study determines total exergy losses caused throughout the life cycle of the heat pump. Moreover, an LCA study using SimaPro was conducted, which provides insight into the different emissions and the overall environmental footprint resulting from the construction, operation (for example, 1, 8, and 15 years), and decommissioning phases of the heat pump. The combined results were compared with those of a fossil fuel oil boiler (OB), a bio-oil boiler (BOB), a natural gas-fired boiler (NGB), and a biogas boiler (BGB).

scholarly journals Evaluation of the Environmental Sustainability of a Stirling Cycle-Based Heat Pump Using LCA

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4469
Author(s):  
Umara Khan ◽  
Ron Zevenhoven ◽  
Tor-Martin Tveit
Keyword(s):  
High Temperature ◽  
Heat Pump ◽  
Waste Heat ◽  
Heat Pumps ◽  
Heat Output ◽  
Environmental Footprint ◽  
Stirling Cycle ◽  
Impact Reduction ◽  
Temperature Heat ◽  
Very High

Heat pumps are increasingly seen as efficient and cost-effective heating systems also in industrial applications. They can drastically reduce the carbon footprint of heating by utilizing waste heat and renewable electricity. Recent research on Stirling cycle-based very high temperature heat pumps is motivated by their promising role in addressing global environmental and energy-related challenges. Evaluating the environmental footprint of a heat pump is not easy, and the impacts of Stirling cycle-based heat pumps, with a relatively high temperature lift have received little attention. In this work, the environmental footprint of a Stirling cycle-based very high temperature heat pump is evaluated using a “cradle to grave” LCA approach. The results for 15 years of use (including manufacturing phase, operation phase, and decommissioning) of a 500-kW heat output rate system are compared with those of natural gas- and oil-fired boilers. It is found that, for the Stirling cycle-based HP, the global warming potential after of 15 years of use is nearly −5000 kg CO2 equivalent. The Stirling cycle-based HP offers an environmental impact reduction of at least 10% up to over 40% in the categories climate change, photochemical ozone formation, and ozone depletion when compared to gas- and oil-fired boilers, respectively.

scholarly journals Research and practice of water source heat pump technology in Heyi station

2020 ◽  
Vol 218 ◽  
pp. 01004
Author(s):  
Shiyao He ◽  
Yongxiang Ren ◽  
Kai Jiao ◽  
Jun Deng ◽  
Yiming Meng ◽  
...  
Keyword(s):  
High Temperature ◽  
Crude Oil ◽  
Heat Pump ◽  
Waste Heat ◽  
Water Source ◽  
High Energy ◽  
Fuel Oil ◽  
Thermal System ◽  
Production Plant ◽  
Production Safety

There are some problems in the thermal system of Huabei Oilfield, such as high energy consumption, high operation cost and poor production safety. With more stringent requirements for energy conservation and emission reduction, it is particularly important to replace fuel oil projects and improve the efficiency of heating system.The utilization of waste heat and waste heat resources in Huabei Oilfield and the application conditions of various heat pump technologies were investigated, according to the characteristics of large amount of sewage and high temperature produced by crude oil dehydration in Huabei Oilfield. Aiming at the characteristics of large amount of sewage and high temperature produced by crude oil dehydration in Huabei Oilfield, Pilot Application of Optimized Extracted Water Source Heat Pump Technology, the research results are applied to the the He Yi Station in the third oil production plant, estimating the scale and benefit of saving, finally, the purpose of reducing cost and increasing efficiency is achieved, and the data basis and technical guidance for energy saving renovation of thermal system in the future are improved.

scholarly journals Local Heating Networks with Waste Heat Utilization: Low or Medium Temperature Supply?

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 954 ◽  
Author(s):  
Hanne Kauko ◽  
Daniel Rohde ◽  
Armin Hafner
Keyword(s):  
Low Temperature ◽  
Heat Pump ◽  
Urban Areas ◽  
Waste Heat ◽  
Local Heating ◽  
District Heating ◽  
Heat Pumps ◽  
Hot Water ◽  
Local Network ◽  
Medium Temperature

District heating enables an economical use of energy sources that would otherwise be wasted to cover the heating demands of buildings in urban areas. For efficient utilization of local waste heat and renewable heat sources, low distribution temperatures are of crucial importance. This study evaluates a local heating network being planned for a new building area in Trondheim, Norway, with waste heat available from a nearby ice skating rink. Two alternative supply temperature levels have been evaluated with dynamic simulations: low temperature (40 °C), with direct utilization of waste heat and decentralized domestic hot water (DHW) production using heat pumps; and medium temperature (70 °C), applying a centralized heat pump to lift the temperature of the waste heat. The local network will be connected to the primary district heating network to cover the remaining heat demand. The simulation results show that with a medium temperature supply, the peak power demand is up to three times higher than with a low temperature supply. This results from the fact that the centralized heat pump lifts the temperature for the entire network, including space and DHW heating demands. With a low temperature supply, heat pumps are applied only for DHW production, which enables a low and even electricity demand. On the other hand, with a low temperature supply, the district heating demand is high in the wintertime, in particular if the waste heat temperature is low. The choice of a suitable supply temperature level for a local heating network is hence strongly dependent on the temperature of the available waste heat, but also on the costs and emissions related to the production of district heating and electricity in the different seasons.

scholarly journals Conventional and Advanced Exergoeconomic Analysis of a Compound Ejector-Heat Pump for Simultaneous Cooling and Heating

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3511
Author(s):  
Ali Khalid Shaker Al-Sayyab ◽  
Joaquín Navarro-Esbrí ◽  
Victor Manuel Soto-Francés ◽  
Adrián Mota-Babiloni
Keyword(s):  
Heat Pump ◽  
Exergy Analysis ◽  
Waste Heat ◽  
District Heating ◽  
Cost Comparison ◽  
Exergy Destruction ◽  
Pump System ◽  
Heat Pump System ◽  
Destruction Rate ◽  
Exergoeconomic Analysis

This work focused on a compound PV/T waste heat driven ejector-heat pump system for simultaneous data centre cooling and waste heat recovery for district heating. The system uses PV/T waste heat as the generator’s heat source, acting with the vapour generated in an evaporative condenser as the ejector drive force. Conventional and advanced exergy and advanced exergoeconomic analyses are used to determine the cause and avoidable degree of the components’ exergy destruction rate and cost rates. Regarding the conventional exergy analysis for the whole system, the compressor represents the largest exergy destruction source of 26%. On the other hand, the generator shows the lowest sources (2%). The advanced exergy analysis indicates that 59.4% of the whole system thermodynamical inefficiencies can be avoided by further design optimisation. The compressor has the highest contribution to the destruction in the avoidable exergy destruction rate (21%), followed by the ejector (18%) and condenser (8%). Moreover, the advanced exergoeconomic results prove that 51% of the system costs are unavoidable. In system components cost comparison, the highest cost comes from the condenser, 30%. In the same context, the ejector has the lowest exergoeconomic factor, and it should be getting more attention to reduce the irreversibility by design improving. On the contrary, the evaporator has the highest exergoeconomic factor (94%).

scholarly journals The Role of the Recuperator in High Performance Gas Turbine Applications

1978 ◽  
Author(s):  
C. F. McDonald
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Closed Cycle ◽  
Exhaust Waste Heat ◽  
Prime Movers

With soaring fuel costs and diminishing clean fuel availability, the efficiency of the industrial gas turbine must be improved by utilizing the exhaust waste heat by either incorporating a recuperator or by co-generation, or both. In the future, gas turbines for power generation should be capable of operation on fuels hitherto not exploited in this prime-mover, i.e., coal and nuclear fuel. The recuperative gas turbine can be used for open-cycle, indirect cycle, and closed-cycle applications, the latter now receiving renewed attention because of its adaptability to both fossil (coal) and nuclear (high temperature gas-cooled reactor) heat sources. All of these prime-movers require a viable high temperature heat exchanger for high plant efficiency. In this paper, emphasis is placed on the increasingly important role of the recuperator and the complete spectrum of recuperative gas turbine applications is surveyed, from lightweight propulsion engines, through vehicular and industrial prime-movers, to the large utility size nuclear closed-cycle gas turbine. For each application, the appropriate design criteria, types of recuperator construction (plate-fin or tubular etc.), and heat exchanger material (metal or ceramic) are briefly discussed.

Experimental study of operating characteristics of compression/absorption high-temperature hybrid heat pump using waste heat

2013 ◽  
Vol 54 ◽  
pp. 13-19 ◽  
Author(s):  
Jiyoung Kim ◽  
Seong-Ryong Park ◽  
Young-Jin Baik ◽  
Ki-Chang Chang ◽  
Ho-Sang Ra ◽  
...  
Keyword(s):  
Experimental Study ◽  
High Temperature ◽  
Heat Pump ◽  
Waste Heat ◽  
Operating Characteristics ◽  
Hybrid Heat Pump

Heat Integration of Absorption Heat Pump in a Milk Powder Dairy

2000 ◽  
Author(s):  
Jens Møller Andersen
Keyword(s):  
Heat Pump ◽  
Waste Heat ◽  
Cooling System ◽  
Milk Powder ◽  
Electricity Consumption ◽  
Heat Pumps ◽  
Heat Integration ◽  
Absorption Heat Pump ◽  
Absorption Cooling ◽  
Absorption Cooling System

Abstract Heat integration with absorption heat pumps requires investigation of many types of plant designs. In this article, it is concluded that in many cases high temperature absorption systems for heat recovery are more economically feasible than absorption systems for cooling purposes. The conclusion is based on a project where the scope was to investigate technical and economical possibilities for heat integration of an absorption heat pump in a milk powder plant. The first idea behind the project was to use the waste heat from the rejected air to drive an absorption cooling system to reduce the electricity consumption for cooling proposes. The model of the plant was based on simulations as a background for a time averaged COP model. It was concluded that an absorption system for generating low temperature steam is more feasible.

scholarly journals Critical Analysis of Process Integration Options for Joule-Cycle and Conventional Heat Pumps

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 635 ◽  
Author(s):  
Limei Gai ◽  
Petar Sabev Varbanov ◽  
Timothy Gordon Walmsley ◽  
Jiří Jaromír Klemeš
Keyword(s):  
Heat Pump ◽  
Process Integration ◽  
Waste Heat ◽  
Correct Choice ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Large Temperature ◽  
Temperature Changes ◽  
Application Range ◽  
Source And Sink

To date, research on heat pumps (HP) has mainly focused on vapour compression heat pumps (VCHP), transcritical heat pumps (TCHP), absorption heat pumps, and their heat integration with processes. Few studies have considered the Joule cycle heat pump (JCHP), which raises several questions. What are the characteristics and specifics of these different heat pumps? How are they different when they integrate with the processes? For different processes, which heat pump is more appropriate? To address these questions, the performance and integration of different types of heat pumps with various processes have been studied through Pinch Methodology. The results show that different heat pumps have their own optimal application range. The new JCHP is suitable for processes in which the temperature changes of source and sink are both massive. The VCHP is more suitable for the source and sink temperatures, which are near-constant. The TCHP is more suitable for sources with small temperature changes and sinks with large temperature changes. This study develops an approach that provides guidance for the selection of heat pumps by applying Process Integration to various combinations of heat pump types and processes. It is shown that the correct choice of heat pump type for each application is of utmost importance, as the Coefficient of Performance can be improved by up to an order of magnitude. By recovering and upgrading process waste heat, heat pumps can save 15–78% of the hot utility depending on the specific process.

scholarly journals Possibility of Calcium Oxide from Natural Limestone Including Impurities for Chemical Heat Pump

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 803
Author(s):  
LanXin Lai ◽  
Toshio Imai ◽  
Motohiro Umezu ◽  
Mamoru Ishii ◽  
Hironao Ogura
Keyword(s):  
Heat Pump ◽  
Calcium Oxide ◽  
Waste Heat ◽  
Heat Pumps ◽  
Raw Material ◽  
Hydration Reaction ◽  
Chemical Heat ◽  
Chemical Heat Pump ◽  
Thermogravimetric Analyzer ◽  
Save Energy

Improving energy recycle is an important way to save energy resources and preserve the global environment. Chemical heat pump (CHP) is a technology for saving energy, which utilizes chemical reactions to store thermal energy such as waste heat and solar heat, then release it to provide heat for heating/cooling/refrigeration. For a practical CHP, it is necessary to find cheaper and more stable supply materials. In order to evaluate the possibility of calcium oxide from natural Ofunato natural limestone including impurities, we compare Ofunato limestone with Kawara natural limestone and Garou natural limestone from Japan. These calcium oxides worked as a reactant for CaO/H2O/Ca(OH)2 CHP by repeated hydration/dehydration reaction cycle experiments in a thermogravimetric analyzer. As a result, Ofunato CaO exhibits a high hydration reaction rate after decarbonization at 1223 K for 5 h. The reactivity increased by the repeated hydration reaction although the first hydration rate was low. Furthermore, the sintering of impurities in Ofunato limestone occur easier than that in Kawara limestone with lower impurities. The impurities adhered to the surface of the CaO particle to make specific surface area of CaO particle smaller, which could inhibit hydration reaction of CaO particle. Even if Ofunato limestone contains some impurities, it can be utilized as a raw material for chemical heat pumps.

Sign in / Sign up

Export Citation Format

Share Document