scholarly journals Prediction of Surface Quality Based on the Non-Linear Vibrations in Orthogonal Cutting Process: Time Domain Modeling

2019 ◽  
Vol 3 (3) ◽  
pp. 53
Author(s):  
Kibbou ◽  
Dellagi ◽  
Majdouline ◽  
Moufki
Keyword(s):  
Surface Quality ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Rake Angle ◽  
Cutting Conditions ◽  
Process Time ◽  
Mean Deviation ◽  
Non Linear ◽  
Linear Vibrations

This work presents an analysis of relationships between the non-linear vibrations in machining and the machined surface quality from an analytical model based on a predictive machining theory. In order to examine the influences of tool oscillations, several non-linear mechanisms were considered. Additionally, to solve the non-linear problem, a new computational strategy was developed. The resolution algorithm significantly reduces the computational times and makes the iterative approach more stable. In the present approach, the coupling between the tool oscillations and (i) the regenerative effect due to the variation of the uncut chip thickness between two successive passes and/or when the tool leaves the work (i.e., the tool disengagement from the cut), (ii) the friction conditions at the tool–chip interface, and (iii) the tool rake angle was considered. A parametric study was presented. The correlation between the surface quality, the cutting speed, the tool rake angle, and the friction coefficient was analyzed. The results show that, during tool vibrations, the arithmetic mean deviation of the waviness profile is highly non-linear with respect to the cutting conditions, and the model can be useful for selecting optimal cutting conditions.

Finite Element Modeling of Chip Formation in the Domain of Negative Rake Angle Cutting

2003 ◽  
Vol 125 (3) ◽  
pp. 324-332 ◽  
Author(s):  
Y. Ohbuchi ◽  
T. Obikawa
Keyword(s):  
Finite Element ◽  
Finite Element Modeling ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Rake Angle ◽  
Undeformed Chip Thickness ◽  
Element Modeling ◽  
Single Grain ◽  
Serrated Chips

A thermo-elastic-plastic finite element modeling of orthogonal cutting with a large negative rake angle has been developed to understand the mechanism and thermal aspects of grinding. A stagnant chip material ahead of the tool tip, which is always observed with large negative rake angles, is assumed to act like a stable built-up edge. Serrated chips, one of typical shapes of chips observed in single grain grinding experiment, form when analyzing the machining of 0.93%C carbon steel SK-5 with a rake angle of minus forty five or minus sixty degrees. There appear high and low temperature zones alternately according to severe and mild shear in the primary shear zone respectively. The shapes of chips depend strongly on the cutting speed and undeformed chip thickness; as the cutting speed or the undeformed chip thickness decreases, chip shape changes from a serrated type to a bulging one to a wavy or flow type. Therefore, there exists the critical cutting speed over which a chip can form and flow along a rake face for a given large negative rake angle and undeformed chip thickness.

Experimental Study and Theory Prediction on Adiabatic Shear Critical Conditions of Hardened AISI 1045 Steel

2011 ◽  
Vol 189-193 ◽  
pp. 3061-3065
Author(s):  
Guo He Li ◽  
Tie Li Qi ◽  
Yu Jun Cai ◽  
Hong Jun Wang
Keyword(s):  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Adiabatic Shear ◽  
Cutting Conditions ◽  
Critical Conditions ◽  
Aisi 1045 Steel ◽  
Aisi 1045 ◽  
1045 Steel ◽  
Cutting Experiments

Orthogonal cutting experiments of hardened AISI1045 steel(45HRC) are performed to investigate the influence of cutting conditions on adiabatic shear which occurs in the process of chip formation of many materials. It is found that the cutting speed, cutting depth and rake angle all have influence on adiabatic shear and there is a critical cutting speed at which the adiabatic shear appears. By metallurgical observation, the critical cutting speed under different cutting depths and rake angles are given. A model based on linear pertubation analysis is used to predict the adiabatic shear critical cutting conditions of hardened AISI 1045 steel. The comparison of prediction results and that of expriments shows that this prediction model is valid.

Experimental investigation of a slip-line field model for a worn cutting tool

2013 ◽  
Vol 228 (8) ◽  
pp. 1398-1404 ◽  
Author(s):  
Alper Uysal ◽  
Erhan Altan
Keyword(s):  
Wear Rate ◽  
Slip Line ◽  
Field Model ◽  
Cutting Tool ◽  
Flank Wear ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Rake Angle ◽  
Uncut Chip Thickness ◽  
Line Field

In this study, the slip-line field model developed for orthogonal machining with a worn cutting tool was experimentally investigated. Minimum and maximum values of five slip-line angles ( θ1, θ2, δ2, η and ψ) were calculated. The friction forces that were caused by flank wear land, chip up-curl radii and chip thicknesses were calculated by solving the model. It was specified that the friction force increased with increase in flank wear rate and uncut chip thickness and it decreased a little with increase in cutting speed and rake angle. The chip up-curl radius increased with increase in flank wear rate and it decreased with increase in uncut chip thickness. The chip thickness increased with increase in flank wear rate and uncut chip thickness. Besides, the chip thickness increased with increase in rake angle and it decreased with increase in cutting speed.

Finite Element and Experimental Analysis of Edge Defects Formation during Orthogonal Cutting of SiCp/Al Composites

2012 ◽  
Vol 500 ◽  
pp. 146-151 ◽  
Author(s):  
Ning Hou ◽  
Li Zhou ◽  
Shu Tao Huang ◽  
Li Fu Xu
Keyword(s):  
Finite Element ◽  
Chip Formation ◽  
Defect Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Critical Transition ◽  
Cutting Depth ◽  
Edge Defect ◽  
Edge Defects

In this paper, a finite element method was used to dynamically simulate the process of the edge defects formation during orthogonal cutting SiCp/Al composites. The influence of the cutting speed, cutting depth and rake angle of the PCD insert on the size of the edge defects have been investigated by using scanning electron. According to the simulated results, it can be provided that the cutting layer material has an effect on transfer stress and hinder the chip formation in the critical transition stage, and the critical transition point and distance are defined in this stage. The negative shear phenomenon is found when the chip transit to the edge defects in the flexure deformation stage, so the process of the chip formation is the basis of the edge defects formation. In addition, the relationship between the nucleation and propagation direction of the crack and the variation of the edge defect shape on the workpiece was investigated by theory, and it found that the negative shear angle formation is the primary cause of the edge defect formation. A mixed mode crack is found in the crack propagation stage. The sizes of edge defects were measured by the experiment and simulation, and the edge defect size decrease with the increasing of tool rake angle, while increase with increasing cutting depth and cutting speed.

Process-Independent Force Characterization for Metal-Cutting Simulation

1997 ◽  
Vol 119 (1) ◽  
pp. 86-94 ◽  
Author(s):  
D. A. Stephenson ◽  
P. Bandyopadhyay
Keyword(s):  
Metal Cutting ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Rake Angle ◽  
Baseline Data ◽  
Empirical Equations ◽  
Machining Processes ◽  
Workpiece Material ◽  
Bar Turning ◽  
Force Data

Obtaining accurate baseline force data is often the critical step in applying machining simulation codes. The accuracy of the baseline cutting data determines the accuracy of simulated results. Moreover, the testing effort required to generate suitable data for new materials determines whether simulation provides a cost or time advantage over trial-and-error testing. The efficiency with which baseline data can be collected is limited by the fact that simulation programs do not use standard force or pressure equations, so that multiple sets of tests must be performed to simulate different machining processes for the same tool-workpiece material combination. Furthermore, many force and pressure equations do not include rake angle effects, so that separate tests are also required for different cutter geometries. This paper describes a unified method for simulating cutting forces in different machining processes from a common set of baseline data. In this method, empirical equations for cutting pressures or forces as a function of the cutting speed, uncut chip thickness, and tool normal rake angle are fit to baseline data from end turning, bar turning, or fly milling tests. Forces in specific processes are then calculated from the empirical equations using geometric transformations. This approach is shown to accurately predict forces in end turning, bar turning, or fly milling tests on five common tool-work material combinations. As an example application, bar turning force data is used to simulate the torque and thrust force in a combined drilling and reaming process. Extrapolation errors and corrections for workpiece hardness variations are also discussed.

Effect of the Working Diameter to the Surface Quality in Free-Form Surface Milling

2013 ◽  
Vol 581 ◽  
pp. 372-377 ◽  
Author(s):  
Balázs Mikó ◽  
Jozef Beňo
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Free Form ◽  
Effective Diameter ◽  
Test Part ◽  
Free Form Surface ◽  
Free Form Surfaces

The article presents the changing of the working diameter (effective diameter) and its effect to the surface roughness based on milling experiments of a test part in 3D milling of free-form surfaces. The position of the surface and the step depth determine the effective diameter, in case of constant revolution of the tool, the actual cutting speed and the minimal removable chip thickness will change. The article presents the result of the application of the constant cutting speed and feed per tooth.

Experimental Investigation of the Characteristics of Dynamic Cutting Process

1977 ◽  
Vol 99 (2) ◽  
pp. 410-418 ◽  
Author(s):  
M. M. Nigm ◽  
M. M. Sadek
Keyword(s):  
Experimental Investigation ◽  
Theoretical Model ◽  
High Speed ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Shear Plane ◽  
Rake Angle ◽  
Experimental Results ◽  
High Speed Photography ◽  
Cutting Coefficients

The dynamic response of the shear plane and the variations of the dynamic cutting coefficients are experimentally investigated at various values of feed, cutting speed, rake angle, clearance angle, frequency, and amplitude of chip thickness modulation. Wave generating and wave removing cutting tests, in which high-speed photography is used to investigate the geometry of chip formation, are carried out. The theoretical model of dynamic cutting developed in [1] is assessed with reference to these experimental results. A comparison between this model and previous models in relation to the experimental results is also presented.

Cutting Forces in Orthogonal Cutting of Unidirectional GFRP Composites

1996 ◽  
Vol 118 (3) ◽  
pp. 419-425 ◽  
Author(s):  
G. Caprino ◽  
L. Nele
Keyword(s):  
Size Effect ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Vertical Force ◽  
Fibre Direction ◽  
Unit Width ◽  
Relief Angle

The results of orthogonal cutting tests carried out on unidirectional glass fiber reinforced plastic composites, using HSS tools, are presented and discussed. During the tests, performed on a milling machine at very low cutting speed to avoid thermal effects, the cutting speed was held constant and parallel to the fibre direction. Three parameters, namely the tool rake angle α, the tool relief angle γ, and the depth of cut t, were varied. According to the experimental results, the horizontal force per unit width, Fhu, undergoes a dramatic decrease, never verified for metals, with increasing α. Besides, Fhu is only negligibly affected by the relief angle, and linearly increases with t. Similarly to metals, an effect of the depth of cut on the specific energy (size effect) is found also for composites. However, the presented results indicate that the size effect can be analytically modeled in a simple way in the case of composites. The vertical force per unit width, Fvu, exhibits a marked reduction when the relief angle is increased. Fvu, is also very sensitive to the rake angle: the lower α the higher is Fvu. It is shown that this behavior probably reflects a strong influence of the rake angle on the forces developing at the flank. A linear dependence of the vertical force on the depth of cut is also demonstrated. Finally, the experimental data are utilized to obtain empirical formulae, allowing an approximate evaluation of cutting forces.

On the Effects of a Built-Up Edge on Acoustic Emission in Metal Cutting

1990 ◽  
Vol 112 (2) ◽  
pp. 184-189 ◽  
Author(s):  
D. V. Hutton ◽  
Qinghuan Yu
Keyword(s):  
Acoustic Emission ◽  
Experimental Evidence ◽  
Deformation Zone ◽  
Metal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Shear Angle ◽  
Cutting Conditions ◽  
Effective Rake Angle

Experimental evidence is presented which indicates that the presence of a built-up edge can significantly affect the generation of acoustic emission in metal cutting. Results for machining SAE 1018 and 4140 steels show that the built-up edge can mask the generally accepted AE-cutting speed relation when cutting tools having small rake angles are used. Under cutting conditions conducive to development of a built-up edge, it is shown that increased acoustic emission is generated as a result of increased effective rake angle and corresponding increase of shear angle in the primary deformation zone. Three distinct types of built-up edge have been observed and classified as immature, periodic, or developed, according to effect on acoustic emission.

Dynamic Simulation of the Micro-Milling Process Including Minimum Chip Thickness and Size Effect

2012 ◽  
Vol 504-506 ◽  
pp. 1269-1274 ◽  
Author(s):  
François Ducobu ◽  
Edouard Rivière-Lorphèvre ◽  
Enrico Filippi
Keyword(s):  
Size Effect ◽  
Cutting Forces ◽  
Mechanistic Model ◽  
Orthogonal Cutting ◽  
Chip Thickness ◽  
Milling Process ◽  
Cutting Conditions ◽  
Micro Milling ◽  
Minimum Chip Thickness ◽  
Physical Phenomena

Micro-milling with a cutting tool is a manufacturing technique that allows production of parts ranging from several millimeters to several micrometers. The technique is based on a downscaling of macroscopic milling process. Micro-milling is one of the most effective process to produce complex three-dimensional micro-parts, including sharp edges and with a good surface quality. Reducing the dimensions of the cutter and the cutting conditions requires taking into account physical phenomena that can be neglected in macro-milling. These phenomena include a size effect (nonlinear rising of specific cutting force when chip thickness decreases), the minimum chip thickness (under a given dimension, no chip can be machined) and the heterogeneity of the material (the size of the grains composing the material is significant as compared to the dimension of the chip). The aim of this paper is to introduce some phenomena, appearing in micromilling, in the mechanistic dynamic simulation software ‘dystamill’ developed for macro-milling. The software is able to simulate the cutting forces, the dynamic behavior of the tool and the workpiece and the kinematic surface finish in 2D1/2 milling operation (slotting, face milling, shoulder milling,…). It can be used to predict chatter-free cutting condition for example. The mechanistic model of the cutting forces is deduced from the local FEM simulation of orthogonal cutting. This FEM model uses the commercial software ABAQUS and is able to simulate chip formation and cutting forces in an orthogonal cutting test. This model is able to reproduce physical phenomena in macro cutting conditions (including segmented chip) as well as specific phenomena in micro cutting conditions (minimum chip thickness and size effect). The minimum chip thickness is also taken into account by the global model. The results of simulation for the machining of titanium alloy Ti6Al4V under macro and micro milling condition with the mechanistic model are presented discussed. This approach connects together local machining simulation and global models.

Sign in / Sign up

Export Citation Format

Share Document