Cutting Forces in Orthogonal Cutting of Unidirectional GFRP Composites

1996 ◽  
Vol 118 (3) ◽  
pp. 419-425 ◽  
Author(s):  
G. Caprino ◽  
L. Nele
Keyword(s):  
Size Effect ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Vertical Force ◽  
Fibre Direction ◽  
Unit Width ◽  
Relief Angle

The results of orthogonal cutting tests carried out on unidirectional glass fiber reinforced plastic composites, using HSS tools, are presented and discussed. During the tests, performed on a milling machine at very low cutting speed to avoid thermal effects, the cutting speed was held constant and parallel to the fibre direction. Three parameters, namely the tool rake angle α, the tool relief angle γ, and the depth of cut t, were varied. According to the experimental results, the horizontal force per unit width, Fhu, undergoes a dramatic decrease, never verified for metals, with increasing α. Besides, Fhu is only negligibly affected by the relief angle, and linearly increases with t. Similarly to metals, an effect of the depth of cut on the specific energy (size effect) is found also for composites. However, the presented results indicate that the size effect can be analytically modeled in a simple way in the case of composites. The vertical force per unit width, Fvu, exhibits a marked reduction when the relief angle is increased. Fvu, is also very sensitive to the rake angle: the lower α the higher is Fvu. It is shown that this behavior probably reflects a strong influence of the rake angle on the forces developing at the flank. A linear dependence of the vertical force on the depth of cut is also demonstrated. Finally, the experimental data are utilized to obtain empirical formulae, allowing an approximate evaluation of cutting forces.

Predictive Modeling and Optimization of Cutting Forces Through RSM and Taguchi Techniques in the Turning of ASTM B574 (Hastelloy C-22)

2018 ◽  
pp. 398-417
Author(s):  
İsmail Kırbaş ◽  
Musa Peker ◽  
Gültekin Basmacı ◽  
Mustafa Ay
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Effective Parameters ◽  
Factors Affecting ◽  
The Impact

In this chapter, the impact of cutting parameters (depth of cut, cutting speed, feed, flow, rake angle, lead angle) on cutting forces in the turning process with regard to ASTM B574 (Hastelloy C-22) material has been investigated. Variance analysis has been applied in order to determine the factors affecting the cutting forces. The optimization of the parameters affecting the surface roughness has been obtained using response surface methodology (RSM) based on the Taguchi orthogonal experimental design. The accuracy of the developed models required for the estimation of the force values (Fx, Fy, Fz) is quite successful. In this study, where the R2 value has been used as the criterion/measure, accuracy values of 93.35%, 95.03%, and 95.09% have been achieved for Fx, Fy, and Fz, respectively. As a result of the ANOVA analysis, the most effective parameters for Fx at a 95% confidence interval are depth of cut, feed rate, flow, and rake angle. The most effective parameter for Fy is depth of cut, while the most effective parameters for Fz are depth of cut, feed rate, and flow, respectively.

Finite Element Simulation of Cutting Forces in Orthogonal Machining of Titanium Alloy Ti-6Al-4V

2014 ◽  
Vol 474 ◽  
pp. 192-199 ◽  
Author(s):  
Ladislav Kandráč ◽  
Ildikó Maňková ◽  
Marek Vrabel' ◽  
Jozef Beňo
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Experimental Studies ◽  
Cutting Speed ◽  
Rake Angle ◽  
Simulation Software ◽  
Tool Geometry ◽  
Element Method

In this paper, a Lagrangian finite element-based machining model is applied in the simulation of cutting forces in two-dimensional orthogonal cutting of titanium Ti-6Al-4V alloy. The simulations were conducted using 2D Finite Element Method (FEM) machining simulation software. In addition, the cutting experiments were carried out under the different cutting speed, feed and tool geometry (rake angle, clearance angle and cutting edge radius). The effect of cutting speed, feed and tool geometry on cutting force were investigated. The results obtained from the finite element method (FEM) and experimental studies were compared.

Impact of Tool Geometry on Cutting Dynamics

2007 ◽  
Author(s):  
Achala V. Dassanayake ◽  
C. Steve Suh
Keyword(s):  
Feed Rate ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Rake Angle ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Unstable System ◽  
Edge Angle ◽  
Cutting Force Components ◽  
Force Components

Machining stability in response to changing tool geometry is studied using a 3D turning model that considers coupled tool-workpiece dynamics subject to nonlinear regenerative cutting forces [1]. As tool geometry varies with the specified tool angles, values of tool rake angle, side cutting edge angle, and inclination angle are considered in the study as the controlled parameters. In the presented model, cutting force components in the X, Y, and Z directions vary with the variations of tool geometry, thus resulting in changes in cutting dynamics — a major feature not attainable using 1D models. It is found that tool geometry does have a significant effect on machining stability. In contrast to commonly used stability charts that are created by considering varying cutting speed and depth-of-cut (DOC), the study makes an observation that tool geometry can be a variable effective in restoring an unstable system back to stability without having to resort to changing cutting speed, feed rate or DOC.

scholarly journals Fracture energy for orthogonal cutting in unidirectional CFRP at different cutting directions

2022 ◽  
Vol 1217 (1) ◽  
pp. 012011
Author(s):  
A N Amir ◽  
H Ghazali ◽  
H Wang ◽  
L Ye ◽  
N A Fadi ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Fracture Energy ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Rake Angle ◽  
Balance Model ◽  
Fracture Mechanisms ◽  
Cutting Depth ◽  
Fibre Direction ◽  
Cfrp Laminate

Abstract A unidirectional carbon fibre reinforced polymer (CFRP) laminate is a composite material made up of strong parallel carbon fibres incorporated in a polymer matrix such as epoxy to provide high stiffness and strength in the fibre direction of the laminate. Unfortunately, the interlaminar or intralaminar plane of this material has a low resistance to damages as the fracture toughness of a unidirectional CFRP laminate is related to the energy dissipation during the orthogonal cutting. The aim of this study is on cutting a unidirectional CFRP along the longitudinal or transverse directions, characterizing orthogonal cutting forces and the related fracture energy. Orthogonal cutting is performed using braised carbide tools for a range of cutting depth of 10-100 ³m with a rake angle of 30° to quantify the cutting forces and to observe the fracture mechanisms. The fibre orientations have a significant impact on surface bouncing-back. For some fibre orientations, the energy balance model is applicable, deducting the reasonable value of fracture toughness due to high normal force (F t). Fibre subsurface damage and cutting forces during cutting are found to be strongly influenced by the cutting depth. The input energy of cutting is released in form of new surface energy, fibre breakage, high bending energy, and chip fracture energy.

Experimental and Numerical Investigation into Residual Stress During Turning Operation for Stainless Steel AISI 316

2020 ◽  
Vol 38 (12A) ◽  
pp. 1862-1870
Author(s):  
Safa M. Lafta ◽  
Maan A. Tawfiq
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Orthogonal Cutting ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Percentage Error ◽  
Depth Of Cut ◽  
Main Role ◽  
Turning Operation ◽  
Aisi 316

RS (residual stresses) represent the main role in the performance of structures and machined parts. The main objective of this paper is to investigate the effect of feed rate with constant cutting speed and depth of cut on residual stresses in orthogonal cutting, using Tungsten carbide cutting tools when machining AISI 316 in turning operation. AISI 316 stainless steel was selected in experiments since it is used in many important industries such as chemical, petrochemical industries, power generation, electrical engineering, food and beverage industry. Four feed rates were selected (0.228, 0.16, 0.08 and 0.065) mm/rev when cutting speed is constant 71 mm/min and depth of cutting 2 mm. The experimental results of residual stresses were (-15.75, 12.84, 64.9, 37.74) MPa and the numerical results of residual stresses were (-15, 12, 59, and 37) MPa. The best value of residual stresses is (-15.75 and -15) MPa when it is in a compressive way. The results showed that the percentage error between numerical by using (ABAQUS/ CAE ver. 2017) and experimental work measured by X-ray diffraction is range (2-15) %.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Development of Tooling Cost Model for High Speed Hard Turning

2011 ◽  
Vol 418-420 ◽  
pp. 1482-1485 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz Al Hazza ◽  
Delvis Agusman ◽  
Agus Geter Edy Sutjipto
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cost Model ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Predictive Regression ◽  
Aisi 4340

The current work presents the development of cost model for tooling during high speed hard turning of AISI 4340 hardened steel using regression analysis. A set of experimental data using ceramic cutting tools, composed approximately of Al2O3 (70%) and TiC (30%) on AISI 4340 heat treated to a hardness of 60 HRC was obtained in the following design boundary: cutting speeds (175-325 m/min), feed rate (0.075-0.125 m/rev), negative rake angle (0 to -12) and depth of cut of (0.1-0.15) mm. The output data is used to develop a new model in predicting the tooling cost using in terms of cutting speed, feed rate, depth of cut and rake angle. Box Behnken Design was used in developing the model. Predictive regression model was found to be capable of good predictions the tooling cost within the boundary design.

Finite Element and Experimental Analysis of Edge Defects Formation during Orthogonal Cutting of SiCp/Al Composites

2012 ◽  
Vol 500 ◽  
pp. 146-151 ◽  
Author(s):  
Ning Hou ◽  
Li Zhou ◽  
Shu Tao Huang ◽  
Li Fu Xu
Keyword(s):  
Finite Element ◽  
Chip Formation ◽  
Defect Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Critical Transition ◽  
Cutting Depth ◽  
Edge Defect ◽  
Edge Defects

In this paper, a finite element method was used to dynamically simulate the process of the edge defects formation during orthogonal cutting SiCp/Al composites. The influence of the cutting speed, cutting depth and rake angle of the PCD insert on the size of the edge defects have been investigated by using scanning electron. According to the simulated results, it can be provided that the cutting layer material has an effect on transfer stress and hinder the chip formation in the critical transition stage, and the critical transition point and distance are defined in this stage. The negative shear phenomenon is found when the chip transit to the edge defects in the flexure deformation stage, so the process of the chip formation is the basis of the edge defects formation. In addition, the relationship between the nucleation and propagation direction of the crack and the variation of the edge defect shape on the workpiece was investigated by theory, and it found that the negative shear angle formation is the primary cause of the edge defect formation. A mixed mode crack is found in the crack propagation stage. The sizes of edge defects were measured by the experiment and simulation, and the edge defect size decrease with the increasing of tool rake angle, while increase with increasing cutting depth and cutting speed.

The Effect of Prior Cutting Conditions on the Shear Mechanics of Orthogonal Machining

1998 ◽  
Vol 120 (1) ◽  
pp. 13-20 ◽  
Author(s):  
R. Stevenson ◽  
D. A. Stephenson
Keyword(s):  
Material Properties ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Rake Angle ◽  
Cnc Machining ◽  
Machining Process ◽  
Depth Of Cut ◽  
Prior History ◽  
Machining Conditions ◽  
The Difference

It has been proposed several times in the metal-cutting literature that the machining process is non-unique and that the instantaneous machining conditions depend on the prior machining conditions (e.g. depth of cut, rake angle etc.). To evaluate the validity of this concept, a series of experiments was conducted using a highly accurate CNC machining center. For these experiments, the machining conditions were changed during the course of an orthogonal cutting experiment in a repeatable manner and the measured forces compared as a function of prior history. Tests were conducted on several tempers of 1100 aluminum and commercial purity zinc to evaluate the effect of material properties on the machining response. It was found that the change in measured cutting forces which could be ascribed to prior machining history was less than 3 percent and that material properties, particularly work hardening response, had no discernible effect on the magnitude of the difference.

Sign in / Sign up

Export Citation Format

Share Document