scholarly journals Mechanical Characterizations of 3D-printed PLLA/Steel Particle Composites

Materials ◽  
2018 ◽  
Vol 12 (1) ◽  
pp. 1 ◽  
Author(s):  
Hozhabr Mozafari ◽  
Pengfei Dong ◽  
Haitham Hadidi ◽  
Michael Sealy ◽  
Linxia Gu
Keyword(s):  
Elastic Modulus ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Smooth Transition ◽  
Interphase Layer ◽  
Fused Filament Fabrication ◽  
Particle Volume ◽  
Compressive Loads ◽  
3D Printed ◽  
Steel Particle

The objective of this study is to characterize the micromechanical properties of poly-l-lactic acid (PLLA) composites reinforced by grade 420 stainless steel (SS) particles with a specific focus on the interphase properties. The specimens were manufactured using 3D printing techniques due to its many benefits, including high accuracy, cost effectiveness and customized geometry. The adopted fused filament fabrication resulted in a thin interphase layer with an average thickness of 3 µm. The mechanical properties of each phase, as well as the interphase, were characterized by nanoindentation tests. The effect of matrix degradation, i.e., imperfect bonding, on the elastic modulus of the composite was further examined by a representative volume element (RVE) model. The results showed that the interphase layer provided a smooth transition of elastic modulus from steel particles to the polymeric matrix. A 10% volume fraction of steel particles could enhance the elastic modulus of PLLA polymer by 31%. In addition, steel particles took 37% to 59% of the applied load with respect to the particle volume fraction. We found that degradation of the interphase reduced the elastic modulus of the composite by 70% and 7% under tensile and compressive loads, respectively. The shear modulus of the composite with 10% particles decreased by 36%, i.e., lower than pure PLLA, when debonding occurred.

Laminar Convective Nanofluid Flow Over a Backward-Facing Step With an Elastic Bottom Wall

2018 ◽  
Vol 10 (4) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Elastic Modulus ◽  
Solid Particle ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Bottom Wall ◽  
Backward Facing Step ◽  
Particle Volume ◽  
Flexible Wall

In the present study, laminar forced convective nanofluid flow over a backward-facing step was numerically investigated. The bottom wall downstream of the step was flexible, and finite element method was used to solve the governing equations. The numerical simulation was performed for a range of Reynolds number (between 25 and 250), elastic modulus of the flexible wall (between 104 and 106), and solid particle volume fraction (between 0 and 0.035). It was observed that the flexibility of the bottom wall results in the variation of the fluid flow and heat transfer characteristics for the backward-facing step problem. As the value of Reynolds number and solid particle volume fraction enhances, local and average heat transfer rates increase. At the highest value of Reynolds number, heat transfer rate is higher for the case with the wall having lowest value of elastic modulus whereas the situation is reversed for other value of Reynolds number. Average Nusselt number reduces by about 9.21% and increases by about 6.1% for the flexible wall with the lowest elastic modulus as compared to a rigid bottom wall for Reynolds number of 25 and 250. Adding nano-additives to the base fluid results in higher heat transfer enhancements. Average heat transfer rates enhance by about 35.72% and 35.32% at the highest solid particle volume fraction as compared to nanofluid with solid volume fraction of 0.01 for the case with wall at the lowest and highest elastic modulus. A polynomial type correlation for the average Nusselt number along the flexible hot wall was proposed, which is dependent on the elastic modulus and solid particle volume fraction. The results of this study are useful for many thermal engineering problems where flow separation and reattachment coupled with heat transfer occur. Control of convective heat transfer for such configurations with wall flexibility and nanoparticle inclusion to the base fluid was aimed in this study to find the effects of various pertinent parameters for heat transfer enhancement.

Cooling of a Partially Elastic Isothermal Surface by Nanofluids Jet Impingement

2018 ◽  
Vol 140 (4) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Reynolds Number ◽  
Nusselt Number ◽  
Elastic Modulus ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Jet Impingement ◽  
Particle Volume ◽  
Elastic Part ◽  
Hot Surface

Numerical study of nanofluid jet impingement cooling of a partially elastic isothermal hot surface was conducted with finite element method. The impingement surface was made partially elastic, and the effects of Reynolds number (between 25 and 200), solid particle volume fraction (between 0.01 and 0.04), elastic modulus of isothermal hot surface (between 104 and 106), size of the flexible part (between 7.5 w and 25 w), and nanoparticle type (spherical, cylindrical, blade) on the fluid flow and heat transfer characteristics were analyzed. It was observed that average Nusselt number enhances for higher Reynolds number, higher values of elastic modulus of flexible wall, smaller size of elastic part, and higher nanoparticle solid volume fraction and for cylindrical shaped particles. It is possible to change the maximum Nusselt number by 50.58% and 33% by changing the elastic modulus of the hot wall and size of elastic part whereas average Nusselt number changes by only 9.33% and 6.21%. The discrepancy between various particle shapes is higher for higher particle volume fraction.

Numerical Simulation for Mechanical Behavior of Carbon Black Filled Rubber Composites Based on Plane Stress Model

2012 ◽  
Vol 476-478 ◽  
pp. 2543-2547
Author(s):  
Qing Li ◽  
Xiao Xiang Yang
Keyword(s):  
Elastic Modulus ◽  
Carbon Black ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Effective Elastic Modulus ◽  
Volume Element ◽  
Stress Model ◽  
Rubber Composites ◽  
Particle Volume ◽  
Filled Rubber

In this paper, Representative Volume Element with random distribution pattern has been built and applied to study and analyze the macro mechanical properties of the carbon black filled rubber composites by the micromechanical finite element method. And numerical simulations under uniaxial compression have been made by two-dimensional plane stress model. The periodic boundary conditions are imposed on each Representative Volume Element in order to ensure the compatibility of the deformation field. The dependence of the macroscopic stress-strain behavior and the effective elastic modulus of the composites, on particle distribution pattern, particle volume fraction and particle stiffness has been investigated and discussed. It is shown that the stiffness of the composite is increased considerably with the introduction of carbon black filler particles, and the effective elastic modulus of the composite is increased with the increase of the particle volume fraction.

scholarly journals Performance improvement of double-tube gas cooler in CO2 refrigeration system using nanofluids

2015 ◽  
Vol 19 (1) ◽  
pp. 109-118 ◽  
Author(s):  
Jahar Sarkar
Keyword(s):  
Performance Improvement ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Cooling Capacity ◽  
Inlet Temperature ◽  
Refrigeration Cycle ◽  
Particle Volume ◽  
Transcritical Carbon Dioxide ◽  
The Given ◽  
Theoretical Analyses

The theoretical analyses of the double-tube gas cooler in transcritical carbon dioxide refrigeration cycle have been performed to study the performance improvement of gas cooler as well as CO2 cycle using Al2O3, TiO2, CuO and Cu nanofluids as coolants. Effects of various operating parameters (nanofluid inlet temperature and mass flow rate, CO2 pressure and particle volume fraction) are studied as well. Use of nanofluid as coolant in double-tube gas cooler of CO2 cycle improves the gas cooler effectiveness, cooling capacity and COP without penalty of pumping power. The CO2 cycle yields best performance using Al2O3-H2O as a coolant in double-tube gas cooler followed by TiO2-H2O, CuO-H2O and Cu-H2O. The maximum cooling COP improvement of transcritical CO2 cycle for Al2O3-H2O is 25.4%, whereas that for TiO2-H2O is 23.8%, for CuO-H2O is 20.2% and for Cu-H2O is 16.2% for the given ranges of study. Study shows that the nanofluid may effectively use as coolant in double-tube gas cooler to improve the performance of transcritical CO2 refrigeration cycle.

A simulation and experimental study on particle volume fraction of PMMA suspension in centrifugal fields

2021 ◽  
Author(s):  
Yosephus Ardean Kurnianto Prayitno ◽  
Tong Zhao ◽  
Yoshiyuki Iso ◽  
Masahiro Takei
Keyword(s):  
Experimental Study ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Particle Volume

Solidification Processing of Functionally Graded Materials by Sedimentation

1999 ◽  
Author(s):  
J. W. Gao ◽  
S. J. White ◽  
C. Y. Wang
Keyword(s):  
Functionally Graded Materials ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Computer Code ◽  
Functionally Graded ◽  
Particle Volume ◽  
Particle Sedimentation ◽  
Graded Materials ◽  
Free Zone ◽  
Free Region

Abstract A combined experimental and numerical investigation of the solidification process during gravity casting of functionally graded materials (FGMs) is conducted. Focus is placed on the interplay between the freezing front propagation and particle sedimentation. Experiments were performed in a rectangular ingot using pure substances as the matrix and glass beads as the particle phase. The time evolutions of local particle volume fractions were measured by bifurcated fiber optical probes working in the reflection mode. The effects of various processing parameters were explored. It is found that there exists a particle-free zone in the top portion of the solidified ingot, followed by a graded particle distribution region towards the bottom. Higher superheat results in slower solidification and hence a thicker particle-free zone and a higher particle concentration near the bottom. The higher initial particle volume fraction leads to a thinner particle-free region. Lower cooling temperatures suppress particle settling. A one-dimensional solidification model was also developed, and the model equations were solved numerically using a fixed-grid, finite-volume method. The model was then validated against the experimental results, and the validated computer code was used as a tool for efficient computational prototyping of an Al/SiC FGM.

Shock-Induced Multiphase Instability in a High Volume Fraction Finite-Thickness Particle Layer

2021 ◽  
Author(s):  
Bertrand Rollin ◽  
Frederick Ouellet ◽  
Bradford Durant ◽  
Rahul Babu Koneru ◽  
S. Balachandar
Keyword(s):  
Shock Tube ◽  
Volume Fraction ◽  
Solid Phase ◽  
Particle Volume Fraction ◽  
Finite Thickness ◽  
Spherical Particles ◽  
Shock Strength ◽  
Particle Volume ◽  
Particle Cloud ◽  
Particle Layer

Abstract We study the interaction of a planar air shock with a perturbed, monodispersed, particle curtain using point-particle simulations. In this Eulerian-Lagrangian approach, equations of motion are solved to track the position, momentum, and energy of the computational particles while the carrier fluid flow is computed in the Eulerian frame of reference. In contrast with many Shock-Driven Multiphase Instability (SDMI) studies, we investigate a configuration with an initially high particle volume fraction, which produces a strongly two-way coupled flow in the early moments following the shock-solid phase interaction. In the present study, the curtain is about 4 mm in thickness and has a peak volume fraction of about 26%. It is composed of spherical particles of d = 115μm in diameter and a density of 2500 kg.m−3, thus replicating glass particles commonly used in multiphase shock tube experiments or multiphase explosive experiments. We characterize both the evolution of the perturbed particle curtain and the gas initially trapped inside the particle curtain in our planar three-dimensional numerical shock tube. Control parameters such as the shock strength, the particle curtain perturbation wavelength and particle volume fraction peak-to-trough amplitude are varied to quantify their influence on the evolution of the particle cloud and the initially trapped gas. We also analyze the vortical motion in the flow field. Our results indicate that the shock strength is the primary contributor to the cloud particle width. Also, a classic Richtmyer-Meshkov instability mixes the gas initially trapped in the particle curtain and the surrounding gas. Finally, we observe that the particle cloud contribute to the formation of longitudinal vortices in the downstream flow.

Alignment of Nanoplates in Lamellar Diblock Copolymer Domains and the Effect of Particle Volume Fraction on Phase Behavior

2018 ◽  
Vol 7 (12) ◽  
pp. 1400-1407 ◽  
Author(s):  
Nadia M. Krook ◽  
Jamie Ford ◽  
Manuel Maréchal ◽  
Patrice Rannou ◽  
Jeffrey S. Meth ◽  
...  
Keyword(s):  
Phase Behavior ◽  
Diblock Copolymer ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Particle Volume
Sign in / Sign up

Export Citation Format

Share Document