scholarly journals The Effect of the Parameters of T-RTM on the Properties of Polyamide 6 Prepared by in Situ Polymerization

Materials ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 4 ◽  
Author(s):  
Orsolya Viktória Semperger ◽  
András Suplicz
Keyword(s):  
Mechanical Properties ◽  
Automotive Industry ◽  
Cycle Time ◽  
In Situ Polymerization ◽  
Rapid Development ◽  
Polyamide 6 ◽  
Raw Material ◽  
Short Cycle ◽  
Short Cycle Time

With the rapid development of the automotive industry, there is also a significant need to improve the raw materials used. Therefore, the demand is increasing for polymer composites with a focus on mass reduction and recyclability. Thermoplastic polymers are preferred because of their recyclability. As the automotive industry requires mass production, they require a thermoplastic raw material that can impregnate the reinforcement in a short cycle time. The most suitable monomer for this purpose is caprolactam. It can be most efficiently processed with T-RTM (thermoplastic resin transfer molding) technology, during which polyamide 6 is produced from the low-viscosity monomer by anionic ring-opening (in situ) polymerization in a tempered mold with a sufficiently short cycle time. Manufacturing parameters, such as polymerization time and mold temperature, highly influence the morphological and mechanical properties of the product. In this paper, the properties of polyamide 6 produced by T-RTM are analyzed as a function of the production parameters. We determine the crystallinity and the residual monomer content of the samples and their effect on mechanical properties.

scholarly journals Regenerated Antheraea pernyi Silk Fibroin/Poly(N-isopropylacrylamide) Thermosensitive Composite Hydrogel with Improved Mechanical Strength

Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 302 ◽  
Author(s):  
Boxiang Wang ◽  
Song Zhang ◽  
Yifan Wang ◽  
Bo Si ◽  
Dehong Cheng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silk Fibroin ◽  
In Situ Polymerization ◽  
Crosslinking Agent ◽  
Composite Hydrogel ◽  
Raw Material ◽  
Antheraea Pernyi ◽  
Composite Hydrogels ◽  
Polymerization Method

At present, Antheraea pernyi silk fibroin (ASF) has attracted research efforts to investigate it as a raw material for fabrication of biomedical devices because of its superior cytocompatibility. Nevertheless, native ASF is not easily processed into a hydrogel without any crosslinking agent, and a single hydrogel shows poor mechanical properties. In this paper, a series of ASF/poly (N-isopropylacrylamide) (PNIPAAm) composite hydrogels with different ASF contents were manufactured by a simple in situ polymerization method without any crosslinking agent. Meanwhile, the structures, morphologies and thermal properties of composite hydrogels were investigated by XRD, FTIR, SEM, DSC and TGA, respectively. The results indicate that the secondary structure of silk in the composite hydrogel can be controlled by changing the ASF content and the thermal stability of composite hydrogels is enhanced with an increase in crystalline structure. The composite hydrogels showed similar lower critical solution temperatures (LCST) at about 32 °C, which matched well with the LCST of PNIPAAm. Finally, the obtained thermosensitive composite hydrogels exhibited enhanced mechanical properties, which can be tuned by varying the content of ASF. This strategy to prepare an ASF-based responsive composite hydrogel with enhanced mechanical properties represents a valuable route for developing the fields of ASF, and, furthermore, their attractive applications can meet the needs of different biomaterial fields.

Synthesis and Characterizations of Poly(Butylene Succinate) Copolyester

2014 ◽  
Vol 1015 ◽  
pp. 381-384
Author(s):  
Li Liu ◽  
Li Hai Cai ◽  
Dan Liu ◽  
Jun Xu ◽  
Bao Hua Guo
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Crystallization Temperature ◽  
In Situ Polymerization ◽  
Nucleating Agent ◽  
Single Fiber ◽  
Butylene Succinate ◽  
Crystallization Behaviors ◽  
Polymerization Method

The poly (butylene succinate) (PBS) and 3 wt% attapulgite (ATP) reinforced PBS/ATP nanocomposites with 1,6-hexanediol were fabricated using an in situ polymerization method. The crystallization behaviors indicated that ATP had effectively acted as nucleating agent, resulting in the enhancement on the crystallization temperature. The SEM results showed a superior interfacial linkage between ATP and PBS. Also, ATP could disperse as a single fiber and embed in the polymer matrix, which resulted in the improved mechanical properties.

Parametric Study on Separation Performance of Air Drying PSA and Application of Short Cycle Time Approximation.

2000 ◽  
Vol 33 (2) ◽  
pp. 205-210 ◽  
Author(s):  
Hongmei Lou ◽  
Fei Dong ◽  
Yoshiro Tominaga ◽  
Akio Kodama ◽  
Motonobu Goto ◽  
...  
Keyword(s):  
Cycle Time ◽  
Parametric Study ◽  
Separation Performance ◽  
Air Drying ◽  
Short Cycle ◽  
Time Approximation ◽  
Short Cycle Time

Mechanical Properties of Thermoplastic Composites via In Situ Polymerization from Cyclic Oligomers

2013 ◽  
Vol 750-752 ◽  
pp. 7-10
Author(s):  
Kou An Hao ◽  
Zhen Qing Wang ◽  
Li Min Zhou
Keyword(s):  
Mechanical Properties ◽  
In Situ Polymerization ◽  
High Viscosity ◽  
Thermoplastic Composites ◽  
Thermoplastic Matrix ◽  
Polymerization Catalyst ◽  
Short Beam ◽  
Beam Shear ◽  
Cyclic Oligomers

Fiber impregnation has been the main obstacle for thermoplastic matrix with high viscosity. This problem could be surmounted by adapting low viscous polymeric precursors Woven basalt fabric reinforced poly (butylenes terephthalate) composites were produced via in-situ polymerization at T=210°C. Before polymerization, catalyst was introduced to the reinforcement surface with different concentration. DSC is used to determine the polymerization and crystallization. SEM is used to detect whether the catalyst existed on surface. Both flexural and short-beam shear test are employed to study the corresponding mechanical properties.

scholarly journals PA6 and Halloysite Nanotubes Composites with Improved Hydrothermal Ageing Resistance: Role of Filler Physicochemical Properties, Functionalization and Dispersion Technique

Polymers ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 211 ◽  
Author(s):  
Valentina Sabatini ◽  
Tommaso Taroni ◽  
Riccardo Rampazzo ◽  
Marco Bompieri ◽  
Daniela Maggioni ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Polymer Matrix ◽  
In Situ Polymerization ◽  
Cost Effective ◽  
Polyamide 6 ◽  
Halloysite Nanotubes ◽  
Amide Bonds ◽  
Molecular Weights ◽  
Dispersion Technique

Polyamide 6 (PA6) suffers from fast degradation in humid conditions due to hydrolysis of amide bonds, which limits its durability. The addition of nanotubular fillers represents a viable strategy for overcoming this issue, although the additive/polymer interface at high filler content can become privileged site for moisture accumulation. As a cost-effective and versatile material, halloysite nanotubes (HNT) were investigated to prepare PA6 nanocomposites with very low loadings (1–45% w/w). The roles of the physicochemical properties of two differently sourced HNT, of filler functionalization with (3-aminopropyl)triethoxysilane and of dispersion techniques (in situ polymerization vs. melt blending) were investigated. The aspect ratio (5 vs. 15) and surface charge (−31 vs. −59 mV) of the two HNT proved crucial in determining their distribution within the polymer matrix. In situ polymerization of functionalized HNT leads to enclosed and well-penetrated filler within the polymer matrix. PA6 nanocomposites crystal growth and nucleation type were studied according to Avrami theory, as well as the formation of different crystalline structures (α and γ forms). After 1680 h of ageing, functionalized HNT reduced the diffusion of water into polymer, lowering water uptake after 600 h up to 90%, increasing the materials durability also regarding molecular weights and rheological behavior.

Sign in / Sign up

Export Citation Format

Share Document