scholarly journals On the Size Effect of Additives in Amorphous Shape Memory Polymers

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 327
Author(s):  
Elias M. Zirdehi ◽  
Hakan Dumlu ◽  
Gunther Eggeler ◽  
Fathollah Varnik
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Recovery Process ◽  
Size Ratio ◽  
Additive Concentration ◽  
Effect Of Additives ◽  
Dynamics Simulations ◽  
Small Additive

Small additive molecules often enhance structural relaxation in polymers. We explore this effect in a thermoplastic shape memory polymer via molecular dynamics simulations. The additive-to-monomer size ratio is shown to play a key role here. While the effect of additive-concentration on the rate of shape recovery is found to be monotonic in the investigated range, a non-monotonic dependence on the size-ratio emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for controlling the recovery process in polymer-based shape memory materials.

scholarly journals On the Size Effect of Additives in Amorphous Shape Memory Polymers

2020 ◽  
Author(s):  
Elias M. Zirdehi ◽  
Hakan Dumlu ◽  
Gunther Eggeler ◽  
Fathollah Varnik
Keyword(s):  
Molecular Dynamics ◽  
Shape Memory ◽  
Small Molecules ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Recovery Process ◽  
Ambient Fluid ◽  
Effect Of Additives ◽  
Shape Memory Materials ◽  
Dynamics Simulations

Thermal shape memory polymers (SMPs) find increasing applications in biology and medicine due to their promising potential for improved biocompatibility. In such applications, the inevitable penetration of small molecules from the ambient fluid into the polymer influences the shape recovery process and often leads to a reduction of the temperature, at which shape recovery takes place. We show here via molecular dynamics simulations that the size of additive molecules plays a key role for this process. While the effect of concentration on the recovery rate is monotonic in the investigated range, a non-monotonic dependence on the size of additive molecules emerges at temperatures close to the glass transition. This work thus identifies the additives’ size to be a qualitatively novel parameter for switching the recovery process in polymer-based shape memory materials.

Investigate of Electrical Conductivity of Shape-Memory Polymer Filled with Carbon Black

2008 ◽  
Vol 47-50 ◽  
pp. 714-717 ◽  
Author(s):  
Xin Lan ◽  
Jin Song Leng ◽  
Yan Ju Liu ◽  
Shan Yi Du
Keyword(s):  
Electrical Conductivity ◽  
Carbon Black ◽  
Shape Memory ◽  
Shape Recovery ◽  
Volume Fraction ◽  
Shape Memory Polymer ◽  
Recovery Process ◽  
Thermomechanical Properties ◽  
Electrically Conductive ◽  
New System

A new system of thermoset styrene-based shape-memory polymer (SMP) filled with carbon black (CB) is investigated. To realize the electroactive stimuli of SMP, the electrical conductivity of SMP filled with various amounts of CB is characterized. The percolation threshold of electrically conductive SMP filled with CB is about 3% (volume fraction of CB), which is much lower than many other electrically conductive polymers. When applying a voltage of 30V, the shape recovery process of SMP/CB(10 vol%) can be realized in about 100s. In addition, the thermomechanical properties are also characterized by differential scanning calorimetery (DSC).

scholarly journals Polydopamine coated shape memory polymer: enabling light triggered shape recovery, light controlled shape reprogramming and surface functionalization

2016 ◽  
Vol 7 (7) ◽  
pp. 4741-4747 ◽  
Author(s):  
Zhen Li ◽  
Xiaoyong Zhang ◽  
Shiqi Wang ◽  
Yang Yang ◽  
Benye Qin ◽  
...  
Keyword(s):  
Shape Memory ◽  
Surface Functionalization ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Dip Coating ◽  
Responsive Materials ◽  
Thermally Responsive

Simple dip-coating transforms thermally responsive shape memory polymers into photo-responsive materials and allows for shape engineering and surface functionalization.

Shape Memory Properties of Ti-Ni Shape Memory Alloy / Shape Memory Polymer Composites Using Additive Manufacturing

2021 ◽  
Vol 1016 ◽  
pp. 697-701
Author(s):  
Kazuhiro Kitamura
Keyword(s):  
Shape Memory ◽  
Transformation Temperature ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
The Other ◽  
3D Printer ◽  
Shape Memory Material ◽  
Polymer Resin ◽  
Shape Memory Properties

Shape memory alloys (SMAs) have the disadvantage that cooling is difficult and the actuating speed during cooling is slow. To resolve this problem, shape memory material actuators that operate only with heating is required. SMAs are characterized by a low apparent Young's modulus below the transformation temperature and a strong shape recovery force above the reverse transformation temperature. Alternatively, shape memory polymers (SMPs) have two properties: shape fixability and shape recovery. The SMPs are hardened below the glass transition (Tg) temperature and the material is recovered to memorized shape above the Tg temperature. The other hand, 3D printer is a machine that can directly output a 3D-designed product designed by a computer in 3D, and molded materials such as polymer, resin, metal, and ceramics. In this research, we developed the SMC of SMA wire and SMP sheet using adhesive that develops actuates into two shapes only by heating.

Influence of Radialization Dosage on Shape Memory Effect of Polystyrene Copolymer

2008 ◽  
Vol 47-50 ◽  
pp. 690-693 ◽  
Author(s):  
Da Wei Zhang ◽  
Jin Song Leng ◽  
Yan Ju Liu
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Smart Materials ◽  
Shape Recovery ◽  
Memory Performance ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Mechanical Analysis ◽  
Styrene Copolymer

This paper is concerned about the synthesis of shape memory styrene copolymer and the investigation of the influence of radialization dosage on its shape memory effect. As one of novel actuators in smart materials, shape memory polymers (SMPs) have been investigated intensively. Styrene copolymer with proper cross-linking degree can exhibit shape memory effect (SME). In this paper, the influence of radialization on shape memory effect of styrene copolymer was investigated through altering the dosage of radialization. The radialization dosage of styrene copolymer was determined by changed radicalization time. The glass transition temperature (Tg) of styrene copolymerwas measured by Dynamic Mechanical Analysis (DMA). The shape memory performance of styrene copolymer with different radiated dosage was also evaluated. Results indicated that the shape memory polymer (SMP) was synthesized successfully. The Tg increased from 60°C to 65°C followed by increasing the radialization dosage. Moreover, the SMP experienced good SME and the largest reversible strain of the SMP reached as high as 150%. When heating above Tg+30°C (different copolymers performed different Tg), the shape recovery speed of the copolymers increased with increasing the radialization dosage. However, the recovery speed decreased with increasing the radialization dosage at the same temperature of 95°C.

Study on Shape Recovery Behaviors of Epoxy-Based Shape Memory Polymer

2011 ◽  
Vol 179-180 ◽  
pp. 325-328 ◽  
Author(s):  
Bo Zhou ◽  
Xue Lian Wu ◽  
Yan Ju Liu ◽  
Jin Song Leng
Keyword(s):  
Glass Transition ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Shape Recovery ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Numerical Calculations ◽  
Glass Transition Temperatures ◽  
Recovery Experiment

The glass transition temperatures of epoxy-based shape memory polymers (SMPs), which contain a flexibilizer at various contents of 0%, 5%, 10% and 15% respectively, are determined through DMA tests. The shape memory effect of such materials is investigated through shape recovery experiments. Experimental results show that the content of flexibilizer has much influence on the shape memory effect of epoxy-based SMP. A shape recovery equation is developed based on the results of shape recovery experiment. Numerical calculations show that the developed shape recovery equation well predicts the shape recovery behaviors of epoxy-based SMP.

scholarly journals Harnessing reversible dry adhesion using shape memory polymer microparticles

RSC Advances ◽  
2021 ◽  
Vol 11 (32) ◽  
pp. 19616-19622
Author(s):  
Wenbing Li ◽  
Junhao Liu ◽  
Wanting Wei ◽  
Kun Qian
Keyword(s):  
Shape Memory ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Memory Effects ◽  
Reversible Adhesion ◽  
Dry Adhesion ◽  
Bonding Property ◽  
Shape Memory Effects ◽  
Polymer Microparticles

Shape memory polymers can provide excellent bonding property because of their shape memory effects. This paper proposes an adhesive unit that is capable of repeatable smart adhesion and exhibits reversible adhesion under heating.

scholarly journals Structural multi-colour invisible inks with submicron 4D printing of shape memory polymers

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Wang Zhang ◽  
Hao Wang ◽  
Hongtao Wang ◽  
John You En Chan ◽  
Hailong Liu ◽  
...  
Keyword(s):  
Shape Memory ◽  
Information Hiding ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Photonic Devices ◽  
Temperature Sensitive ◽  
4D Printing ◽  
Two Photon ◽  
Shape Memory Effects ◽  
Nanoscale Structure

AbstractFour-dimensional (4D) printing of shape memory polymer (SMP) imparts time responsive properties to 3D structures. Here, we explore 4D printing of a SMP in the submicron length scale, extending its applications to nanophononics. We report a new SMP photoresist based on Vero Clear achieving print features at a resolution of ~300 nm half pitch using two-photon polymerization lithography (TPL). Prints consisting of grids with size-tunable multi-colours enabled the study of shape memory effects to achieve large visual shifts through nanoscale structure deformation. As the nanostructures are flattened, the colours and printed information become invisible. Remarkably, the shape memory effect recovers the original surface morphology of the nanostructures along with its structural colour within seconds of heating above its glass transition temperature. The high-resolution printing and excellent reversibility in both microtopography and optical properties promises a platform for temperature-sensitive labels, information hiding for anti-counterfeiting, and tunable photonic devices.

Structural tuning of polycaprolactone based thermadapt shape memory polymer

2020 ◽  
Vol 11 (7) ◽  
pp. 1369-1374 ◽  
Author(s):  
Wusha Miao ◽  
Weike Zou ◽  
Yingwu Luo ◽  
Ning Zheng ◽  
Qiao Zhao ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Memory Polymer ◽  
Shape Memory Polymers ◽  
Controlled Structures

Polycaprolactone based thermadapt shape memory polymers with precisely controlled structures allow tunable shape reconfigurability.

scholarly journals Water Triggered Shape Memory Materials

2013 ◽  
Vol 3 (1) ◽  
pp. 49-50 ◽  
Author(s):  
Guoguang Niu
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Shape Memory Polymers ◽  
Electrical Current ◽  
Light Illumination ◽  
Poly Ethylene Glycol ◽  
Thermally Induced ◽  
Permanent Shape ◽  
Poly Ethylene ◽  
Novel Strategy

The term "shape memory effect" refers to the ability of a material to be deformed and fixed into a temporary shape, and to recover its original, permanent shape upon an external stimulus (1). Shape memory polymers have attracted much interest because of their unique properties, and applied tremendously in medical area, such as biodegradable sutures, actuators, catheters and smart stents (2, 3). Shape memory usually is a thermally induced process, although it can be activated by light illumination, electrical current, magnetic, or electromagnetic field (4-6). During the process, the materials are heated directly or indirectly above their glass transition temperature (Tg) or the melting temperature (Tm) in order to recover the original shape. Non-thermally induced shape memory polymers eliminate the temperature constrains and enable the manipulation of the shape recovered under ambient temperature (7, 8). Herein, we report a novel strategy of water induced shape memory, in which the formation and dissolution of poly(ethylene glycol) (PEG) crystal is utilized for the fixation and recovery of temporary deformation of hydrophilic polymer. This water-induced shape recovery is less sensitive to temperature, of which 95% deformation is fixed in circumstance and over 75% recovery is reached even at 0 oC.

Sign in / Sign up

Export Citation Format

Share Document