Effect of mold temperature on motion behavior of short glass fibers in injection molding process

2014 ◽  
Vol 73 (5-8) ◽  
pp. 639-645 ◽  
Author(s):  
Xi-Ping Li ◽  
Guo-Qun Zhao ◽  
Can Yang
Keyword(s):  
Injection Molding ◽  
Glass Fibers ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Molding Process ◽  
Short Glass ◽  
Motion Behavior

scholarly journals Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 965 ◽  
Author(s):  
Nguyen Truong Giang ◽  
Pham Son Minh ◽  
Tran Anh Son ◽  
Tran Minh The Uyen ◽  
Thanh-Hai Nguyen ◽  
...  
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Melt Flow ◽  
Flow Focusing ◽  
Molding Process ◽  
Heating Efficiency ◽  
Flow Length ◽  
Insert Plate

In the injection molding field, the flow of plastic material is one of the most important issues, especially regarding the ability of melted plastic to fill the thin walls of products. To improve the melt flow length, a high mold temperature was applied with pre-heating of the cavity surface. In this paper, we present our research on the injection molding process with pre-heating by external gas-assisted mold temperature control. After this, we observed an improvement in the melt flow length into thin-walled products due to the high mold temperature during the filling step. In addition, to develop the heating efficiency, a flow focusing device (FFD) was applied and verified. The simulations and experiments were carried out within an air temperature of 400 °C and heating time of 20 s to investigate a flow focusing device to assist with external gas-assisted mold temperature control (Ex-GMTC), with the application of various FFD types for the temperature distribution of the insert plate. The heating process was applied for a simple insert model with dimensions of 50 mm × 50 mm × 2 mm, in order to verify the influence of the FFD geometry on the heating result. After that, Ex-GMTC with the assistance of FFD was carried out for a mold-reading process, and the FFD influence was estimated by the mold heating result and the improvement of the melt flow length using acrylonitrile butadiene styrene (ABS). The results show that the air sprue gap (h) significantly affects the temperature of the insert and an air sprue gap of 3 mm gives the best heating rate, with the highest temperature being 321.2 °C. Likewise, the actual results show that the height of the flow focusing device (V) also influences the temperature of the insert plate and that a 5 mm high FFD gives the best results with a maximum temperature of 332.3 °C. Moreover, the heating efficiency when using FFD is always higher than without FFD. After examining the effect of FFD, its application was considered, in order to improve the melt flow length in injection molding, which increased from 38.6 to 170 mm, while the balance of the melt filling was also clearly improved.

scholarly journals Constant Temperature Approach for the Assessment of Injection Molding Parameter Influence on the Fatigue Behavior of Short Glass Fiber Reinforced Polyamide 6

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1569
Author(s):  
Selim Mrzljak ◽  
Alexander Delp ◽  
André Schlink ◽  
Jan-Christoph Zarges ◽  
Daniel Hülsbusch ◽  
...  
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Process Parameters ◽  
Fatigue Properties ◽  
Injection Molding Process ◽  
Molding Process ◽  
Short Glass Fiber ◽  
Glass Fiber Reinforced ◽  
Molding Parameter ◽  
Short Glass

Short glass fiber reinforced plastics (SGFRP) offer superior mechanical properties compared to polymers, while still also enabling almost unlimited geometric variations of components at large-scale production. PA6-GF30 represents one of the most used SGFRP for series components, but the impact of injection molding process parameters on the fatigue properties is still insufficiently investigated. In this study, various injection molding parameter configurations were investigated on PA6-GF30. To take the significant frequency dependency into account, tension–tension fatigue tests were performed using multiple amplitude tests, considering surface temperature-adjusted frequency to limit self-heating. The frequency adjustment leads to shorter testing durations as well as up to 20% higher lifetime under fatigue loading. A higher melt temperature and volume flow rate during injection molding lead to an increase of 16% regarding fatigue life. In situ Xray microtomography analysis revealed that this result was attributed to a stronger fiber alignment with larger fiber lengths in the flow direction. Using digital volume correlation, differences of up to 100% in local strain values at the same stress level for different injection molding process parameters were identified. The results prove that the injection molding parameters have a high influence on the fatigue properties and thus offer a large optimization potential, e.g., with regard to the component design.

scholarly journals Prediction of the maximum flow length of a thin injection molded part

2020 ◽  
Vol 40 (9) ◽  
pp. 783-795
Author(s):  
Sara Liparoti ◽  
Vito Speranza ◽  
Annarita De Meo ◽  
Felice De Santis ◽  
Roberto Pantani
Keyword(s):  
Injection Molding ◽  
Maximum Flow ◽  
Mold Temperature ◽  
Complete Characterization ◽  
Rheological Parameters ◽  
Injection Molding Process ◽  
Spiral Flow ◽  
Molding Process ◽  
Molded Part ◽  
Flow Length

AbstractOne of the most significant issues, when thin parts have to be obtained by injection molding (i.e. in micro-injection molding), is the determination of the conditions of pressure, mold temperature, and injection temperature to adopt to completely fill the cavity. Obviously, modern computational methods allow the simulation of the injection molding process for any material and any cavity geometry. However, this simulation requires a complete characterization of the material for what concerns the rheological and thermal parameters, and also a suitable criterion for solidification. These parameters are not always easily reachable. A simple test aimed at obtaining the required parameters is then highly advantageous. The so-called spiral flow test, consisting of measuring the length reached by a polymer in a long cavity under different molding conditions, is a method of this kind. In this work, with reference to an isotactic polypropylene, some spiral flow tests obtained with different mold temperatures and injection pressures are analyzed with a twofold goal: on one side, to obtain from a few simple tests the basic rheological parameters of the material; on the other side, to suggest a method for a quick prediction of the final flow length.

Optimization of Injection Molding Process Parameters with Material Properties Based on GA and BP

2013 ◽  
Vol 345 ◽  
pp. 586-590 ◽  
Author(s):  
Xiao Hong Tan ◽  
Lei Gang Wang ◽  
Wen Shen Wang
Keyword(s):  
Injection Molding ◽  
Process Parameters ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Axial Deformation ◽  
Molding Process ◽  
Melt Temperature ◽  
Bp Network ◽  
Injection Parameters ◽  
Moldflow Simulation

To obtain optimal injection process parameters, GA was used to optimize BP network structure based on Moldflow simulation results. The BP network was set up which considering the relationship between volume shrinkage of plastic parts and injection parameters, such as mold temperature, melt temperature, holding pressure and holding time etc. And the optimal process parameters are obtained, which is agreed with actual results. Using BP network to predict injection parameters impact on parts quality can effectively reduce the difficulty and workload of other modeling methods. This method can be extended to other quality prediction in the process of plastic parts.Keyword: Genetic algorithm (GA);Neural network algorithm (BP);Injection molding process optimization;The axial deformation

The simulation of the warpage rule of the thin-walled part of polypropylene composite based on the coupling effect of mold deformation and injection molding process

2018 ◽  
Vol 25 (3) ◽  
pp. 593-601 ◽  
Author(s):  
Jixiang Zhang ◽  
Xiaoyi Yin ◽  
Fengzhi Liu ◽  
Pan Yang
Keyword(s):  
Injection Molding ◽  
Coupling Effect ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Plastic Part ◽  
Molding Process ◽  
Melt Temperature ◽  
Packing Pressure ◽  
Thin Walled ◽  
Packing Time

Abstract Aiming at the problem that a thin-walled plastic part easily produces warpage, an orthogonal experimental method was used for multiparameter coupling analysis, with mold structure parameters and injection molding process parameters considered synthetically. The plastic part deformation under different experiment schemes was comparatively studied, and the key factors affecting the plastic part warpage were analyzed. Then the injection molding process was optimized. The results showed that the important order of the influence factors for the plastic part warpage was packing pressure, packing time, cooling plan, mold temperature, and melt temperature. Among them, packing pressure was the most significant factor. The optimal injection molding process schemes reducing the plastic part warpage were melt temperature (260°C), mold temperature (60°C), packing pressure (150 MPa), packing time (2 s), and cooling plan 3. In this situation, the forming plate flatness was better.

The Effect of Injection Molding Process Parameters on the Buckling Properties of PBT/Short Glass Fiber Composites

2011 ◽  
Vol 284-286 ◽  
pp. 550-556 ◽  
Author(s):  
Ming Hsiung Ho ◽  
Pin Ning Wang ◽  
Chin Ping Fung
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Process Parameters ◽  
Injection Molding Process ◽  
Skin Area ◽  
Molding Process ◽  
Melt Temperature ◽  
Short Glass Fiber ◽  
Filling Time ◽  
Short Glass

This study investigates the effect of various injection molding process parameters and fiber amount on buckling properties of Polybutylene Terephthalate (PBT)/short glass fiber composite. The buckling specimens were prepared under injection molding process. These forming parameters about filling time, melt temperature and mold temperature that govern injection molding process are discussed. The buckling properties of neat PBT, 15 wt%, and 30 wt% are obtained using two ends fixed fixture and computerized closed-loop server-hydraulic material testing system. The fracture surfaces are observed by scanning electron microscopy (SEM). The global buckling forces are raised when increased the fiber weight percentage of PBT. Also, the fracture mechanisms in PBT and short glass fiber matrix are fiber pullout in skin area and fiber broken at core area. It is found that the addition of short glass fiber can significantly strengthen neat PBT.

Optimization of the Injection Molding Process Parameters Based on Moldflow and Orthogonal Experiment

2013 ◽  
Vol 561 ◽  
pp. 239-243 ◽  
Author(s):  
Yong Nie ◽  
Hui Min Zhang ◽  
Jia Teng Niu
Keyword(s):  
Injection Molding ◽  
Orthogonal Experiment ◽  
Mold Temperature ◽  
Processing Parameters ◽  
Influential Factors ◽  
Injection Molding Process ◽  
Range Analysis ◽  
Molding Process ◽  
Melt Temperature ◽  
Plastic Parts

This article is using Moldflow analysis and orthogonal experimental method during the whole experiment. The injection molding process of motor cover is simulated under various technological conditions.After forming the maximum amount of warpage of plastic parts for evaluation.According to the range analysis of the comprehensive goal, the extent of the overall influence to the processing parameters, such as gate location, melt temperature, mold temperature and holding pressure is clarified.Through analyzing the diagrams of influential factors resulted from the simulation result,the optimized process parameter scheme is obtained and further verified by simulation.

Numerical and Experimental Study on the Injection Moulding of a Thin-Wall Complex Part

2008 ◽  
Author(s):  
Catalin Fetecau ◽  
Ion Postolache ◽  
Felicia Stan
Keyword(s):  
Injection Molding ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Processing Parameters ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Molding Process ◽  
Complex Part ◽  
Filling Time ◽  
Wall Injection

The research presented in this paper involves numerical and experimental efforts to investigate the relative thin-wall injection molding process in order to obtain high dimensional quality complex parts. To better understand the effects of various processing parameters (the filling time, injection pressure, the melting temperature, the mold temperature) on the injection molding of a thin-wall complex part, the molding experiments are regenerated into the computer model using the Moldflow Plastics Insight (MPI) 6.1 software. The computer visualization of the filling phase allows accurate prediction of the location of the flow front, welding lines and air traps. Furthermore, in order to optimize the injection molding process, the effects of the geometry of the runner system on the filling and packing phases are also investigated. It is shown that computational modeling could be used to help the process and mold designer to produce accurate parts.

Sign in / Sign up

Export Citation Format

Share Document