scholarly journals Shear Strength of Hybrid Fibre-Reinforced Ternary Blend Geopolymer Concrete Beams under Flexure

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6634
Author(s):  
V. Sathish Kumar ◽  
N. Ganesan ◽  
P. V. Indira
Keyword(s):  
Shear Strength ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Ternary Blend ◽  
Geopolymer Concrete ◽  
Test Results ◽  
Low Carbon ◽  
Polypropylene Fibres ◽  
Steel Fibres ◽  
Hybrid Fibre

The need to promote sustainable civil infrastructure is one of the most important concerns in the construction industry. Geopolymer composites are one of the promising eco-friendly materials for the development of low carbon concrete. The main objective of this experimental investigation is to study the effect of hybrid fibres on the shear strength of flexural members made with ternary blend geopolymer concrete (TGPC). A total number of 27 reinforced concrete beams of size 100 × 150 × 1200 mm3 were cast and tested for shear. M55 grade of concrete was considered in this study. Crimped steel fibres and polypropylene fibres with an aspect ratio of 66 and 300, respectively, were used in this work. The main variables considered in this investigation involve two volume proportions of steel fibres, viz., 0.5% and 1% as well as four volume proportions of polypropylene fibres viz., 0.1%, 0.15%, 0.2% and 0.25%. The hybrid fibre-reinforced ternary blend geopolymer concrete (HTGPC) beams were compared with TGPC beams without fibres. From the test results, it was clear that incorporating hybrid fibres improved the shear strength and changed the type of failure of the beam from shear to flexure. Moreover, a method to predict the ultimate shear strength of HTGPC was proposed, and the estimated values were found to be the same as the test results.

Shear strength of disturbed regions with corroded stirrups in reinforced concrete beams

2010 ◽  
Vol 37 (8) ◽  
pp. 1045-1056 ◽  
Author(s):  
Christopher Suffern ◽  
Ahmed El-Sayed ◽  
Khaled Soudki
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Corrosion Damage ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Accelerated Corrosion ◽  
Damage Level ◽  
Three Point Bending ◽  
Shear Span

This paper reports experimental data on the structural performance of disturbed regions in reinforced concrete beams with corrosion damage to the embedded steel stirrups. A total of 15 reinforced concrete beams were constructed and tested. The test beams were 350 mm deep, 125 mm wide, and 1850 mm long. The beams were tested in three-point bending under a simply supported span of 1500 mm. Nine beams had the embedded stirrups subjected to accelerated corrosion. The test variables were the corrosion damage level and the shear span-to-depth ratio. The test results indicated that the corroded beams exhibited reduced shear strength in comparison to the uncorroded control specimens. The shear strength reduction was up to 53%. Furthermore, the reduction in shear strength due to the corrosion was found to be greater at smaller shear span-to-depth ratios.

scholarly journals Experimental Investigation of Shear Strength for Steel Fibre Reinforced Concrete Beams

2021 ◽  
Vol 15 (1) ◽  
pp. 81-92
Author(s):  
Constantinos B. Demakos ◽  
Constantinos C. Repapis ◽  
Dimitros P. Drivas
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Shear Strength ◽  
Reinforced Concrete ◽  
Steel Fibre ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Fibre Reinforced Concrete ◽  
Steel Fibres ◽  
Steel Fibre Reinforced Concrete

Aims: The aim of this paper is to investigate the influence of the volume fraction of fibres, the depth of the beam and the shear span-to-depth ratio on the shear strength of steel fibre reinforced concrete beams. Background: Concrete is a material widely used in structures, as it has high compressive strength and stiffness with low cost manufacturing. However, it presents low tensile strength and ductility. Therefore, through years various materials have been embedded inside it to improve its properties, one of which is steel fibres. Steel fibre reinforced concrete presents improved flexural, tensile, shear and torsional strength and post-cracking ductility. Objective: A better understanding of the shear performance of SFRC could lead to improved behaviour and higher safety of structures subject to high shear forces. Therefore, the influence of steel fibres on shear strength of reinforced concrete beams without transverse reinforcement is experimentally investigated. Methods: Eighteen concrete beams were constructed for this purpose and tested under monotonic four-point bending, six of which were made of plain concrete and twelve of SFRC. Two different aspect ratios of beams, steel fibres volume fractions and shear span-to-depth ratios were selected. Results: During the experimental tests, the ultimate loading, deformation at the mid-span, propagation of cracks and failure mode were detected. From the tests, it was shown that SFRC beams with high volume fractions of fibres exhibited an increased shear capacity. Conclusion: The addition of steel fibres resulted in a slight increase of the compressive strength and a significant increase in the tensile strength of concrete and shear resistance capacity of the beam. Moreover, these beams exhibit a more ductile behaviour. Empirical relations predicting the shear strength capacity of fibre reinforced concrete beams were revised and applied successfully to verify the experimental results obtained in this study.

scholarly journals Engineering Properties of Hybrid Fibre Reinforced Ternary Blend Geopolymer Concrete

2021 ◽  
Vol 5 (8) ◽  
pp. 203
Author(s):  
V. Sathish Kumar ◽  
N. Ganesan ◽  
P. V. Indira
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Engineering Properties ◽  
Ternary Blend ◽  
Geopolymer Concrete ◽  
Polypropylene Fibres ◽  
Hybrid Form ◽  
Steel Fibres

The primary aim of this research is to find an alternative for Portland cement using inorganic geopolymers. This study investigated the effect of steel and polypropylene fibres hybridisation on ternary blend geopolymer concrete (TGPC) engineering properties using fly ash, ground granulated blast furnace slag (GGBS) and metakaolin as the source materials. The properties like compressive strength, splitting tensile strength, flexural strength and modulus of elasticity of ternary blend geopolymer concrete. The standard tests were conducted on TGPC with steel fibres, polypropylene fibres and a combination of steel and polypropylene fibres in hybrid form. A total number of 45 specimens were tested and compared to determine each property. The grade of concrete considered was M55. The variables studied were the volume fraction of fibres, viz. steel fibres (0%, 0.5% and 1%) and polypropylene fibres (0%, 0.1%, 0.15%, 0.2% and 0.25%). The experimental results reveal that the addition of fibres in a hybrid form enhances the mechanical properties of TGPC. The increase in the compressive strength was nominal, and a significant improvement was observed in splitting tensile strength, flexural strength, and modulus of elasticity. Also, an attempt to obtain the relation between the different engineering properties was made with different volume fractions of fibre.

Effect of Beam Depth and Longitudinal Reinforcement Ratio on Shear Strength of RC Beams

2010 ◽  
Vol 163-167 ◽  
pp. 1460-1465
Author(s):  
Lei Yu ◽  
Yi Che ◽  
Xin Feng Zheng ◽  
Jin Xin Gong ◽  
Yu Pu Song
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Shear Behaviour ◽  
Longitudinal Reinforcement ◽  
Test Results ◽  
Beam Depth ◽  
Insight Into

Seven beams were tested to investigate the effects of beam depth and longitudinal reinforcement ratio on the shear strength of reinforced concrete beams. To investigate the effects of beam depth on shear strength, beams of five different sizes were tested. Two beams were designed to investigate the shear behaviour of beams with small percentage of longitudinal reinforcement. In addition to an experimental investigation, a survey of data in the literature was performed to gain insight into the influence of beam depth and longitudinal reinforcement ratio. Based on test results and a data analysis, conclusions regarding the influence of beam depth and longitudinal reinforcement ratio on shear strength of reinforced concrete beams are presented herein.

Shear strength of reinforced concrete beams with T-headed bars for safety-related nuclear structures

2021 ◽  
Vol 230 ◽  
pp. 111705
Author(s):  
Yuxing Yang ◽  
Amit H. Varma ◽  
Michael E. Kreger ◽  
Ying Wang ◽  
Kai Zhang
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Nuclear Structures

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

Sign in / Sign up

Export Citation Format

Share Document