scholarly journals Engineering Properties of Hybrid Fibre Reinforced Ternary Blend Geopolymer Concrete

2021 ◽  
Vol 5 (8) ◽  
pp. 203
Author(s):  
V. Sathish Kumar ◽  
N. Ganesan ◽  
P. V. Indira
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Engineering Properties ◽  
Ternary Blend ◽  
Geopolymer Concrete ◽  
Polypropylene Fibres ◽  
Hybrid Form ◽  
Steel Fibres

The primary aim of this research is to find an alternative for Portland cement using inorganic geopolymers. This study investigated the effect of steel and polypropylene fibres hybridisation on ternary blend geopolymer concrete (TGPC) engineering properties using fly ash, ground granulated blast furnace slag (GGBS) and metakaolin as the source materials. The properties like compressive strength, splitting tensile strength, flexural strength and modulus of elasticity of ternary blend geopolymer concrete. The standard tests were conducted on TGPC with steel fibres, polypropylene fibres and a combination of steel and polypropylene fibres in hybrid form. A total number of 45 specimens were tested and compared to determine each property. The grade of concrete considered was M55. The variables studied were the volume fraction of fibres, viz. steel fibres (0%, 0.5% and 1%) and polypropylene fibres (0%, 0.1%, 0.15%, 0.2% and 0.25%). The experimental results reveal that the addition of fibres in a hybrid form enhances the mechanical properties of TGPC. The increase in the compressive strength was nominal, and a significant improvement was observed in splitting tensile strength, flexural strength, and modulus of elasticity. Also, an attempt to obtain the relation between the different engineering properties was made with different volume fractions of fibre.

scholarly journals Effect of Iron Filings on the Mechanical Properties of Different Types of Sustainable Concrete

2018 ◽  
Vol 12 (1) ◽  
pp. 441-457 ◽  
Author(s):  
Sahar Jabbar Alserai ◽  
Wissam Kadhim Alsaraj ◽  
Zina Waleed Abass
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Indirect Tensile Strength ◽  
Recycled Aggregate ◽  
Geopolymer Concrete ◽  
Normal Concrete ◽  
Natural Aggregate ◽  
Indirect Tensile

Introduction:One of Iraq’s major environmental problems is a large amount of residual iron produced by the industrial sector, which is stored in domestic waste and landfills. The reuse of construction waste gives two aims, the first is to remove large quantities of pollution resulted from these waste, the second provides cheap resources for concrete aggregates.Methods:This study conducted a series of experiments and tests to test the feasibility of reusing this iron slag and recycled concrete aggregate in concrete mixtures. Different percentages of iron filings were used in the concrete mixture at 0, 0.5%, 0.75% and 1%. Tests are done to evaluate the quality of cast iron concrete which include compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) for four sustainable concretes.Results and Conclusion:The results show that the iron filings amount is increased to 1.0% which resulted in increasing percentage of compressive strength (fcu), flexural strength (fr), indirect tensile strength (ft), SEM and modulus of elasticity (Ec) with 10%, 32%, 42% and 11% for Geopolymer Concrete with Recycled Aggregate (GCRA), 9%, 52%,31% and 17% for geopolymer concrete with natural aggregate (GCNA), 10%, 19%,26% and 12% for Normal Concrete with Natural Aggregate (NCNA) and 23%, 19%, 67% and 14% for Normal Concrete with Recycled Aggregate (NCRA), respectively.

scholarly journals Effect of Recycled Coarse Aggregates in Properties of Concrete

2008 ◽  
Vol 3 (4) ◽  
pp. 130-137 ◽  
Author(s):  
R Kumutha ◽  
K Vijai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Coarse Aggregate ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Split Tensile Strength ◽  
Coarse Aggregates ◽  
The Cost

The properties of concrete containing coarse recycled aggregates were investigated. Laboratory trials were conducted to investigate the possibility of using recycled aggregates from the demolition wastes available locally as the replacement of natural coarse aggregates in concrete. A series of tests were carried out to determine the density, compressive strength, split tensile strength, flexural strength and modulus of elasticity of concrete with and without recycled aggregates. The water cement ratio was kept constant for all the mixes. The coarse aggregate in concrete was replaced with 0%, 20%, 40%, 60%, 80% and 100% recycled coarse aggregates. The test results indicated that the replacement of natural coarse aggregates by recycled aggregates up to 40% had little effect on the compressive strength, but higher levels of replacement reduced the compressive strength. A replacement level of 100% causes a reduction of 28% in compressive strength, 36% in split tensile strength and 50% in flexural strength. For strength characteristics, the results showed a gradual decrease in compressive strength, split tensile strength, flexural strength and modulus of elasticity as the percentage of recycled aggregate used in the specimens increased. 100% replacement of natural coarse aggregate by recycled aggregate resulted in 43% savings in the cost of coarse aggregates and 9% savings in the cost of concrete.

scholarly journals Production of lightweight Geopolymer concrete using artificial local lightweight aggregate

2018 ◽  
Vol 162 ◽  
pp. 02024
Author(s):  
Waleed Abbas ◽  
Wasan Khalil ◽  
Ibtesam Nasser
Keyword(s):  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Lightweight Concrete ◽  
Lightweight Aggregate ◽  
Experimental Tests ◽  
Pulse Velocity ◽  
Dry Density ◽  
Geopolymer Concrete

Due to the rapid depletion of natural resources, the use of waste materials and by-products from different industries of building construction has been gaining increased attention. Geopolymer concrete based on Pozzolana is a new material that does not need the presence of Portland cement as a binder. The main focus of this research is to produce lightweight geopolymer concrete (LWGPC) using artificial coarse lightweight aggregate which produced from locally available bentonite clays. In this investigation, the binder is low calcium fly ash (FA) and the alkali activator is sodium hydroxide and sodium silicate in different molarities. The experimental tests including workability, fresh density, also, the compressive strength, splitting tensile strength, flexural strength, water absorption and ultrasonic pulse velocity at the age of 7, 28 and 56 days were studied. The oven dry density and thermal conductivity at 28 days age are investigated. The results show that it is possible to produce high strength lightweight geopolymer concrete successfully used as insulated structural lightweight concrete. The 28-day compressive strength, tensile strength, flexural strength, dry density, and thermal conductivity of the produced LWGPC are 35.8 MPa, 2.6MPa, 5.5 MPa, 1835kg/m3, and 0.9567 W/ (m. K), respectively.

scholarly journals Research on the Effect of Cooper Slag as a Fine Aggregate on the Properties of Concrete

2019 ◽  
Vol 8 (2S3) ◽  
pp. 619-623
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Copper Slag ◽  
Splitting Tensile Strength ◽  
Copper Recovery ◽  
Concrete Mixture ◽  
Copper Smelting ◽  
Fine Aggregate

Copper slag is a rough blasting grit or a by-product acquired by the process of copper smelting and refining. These copper slags are recycled for copper recovery. In this paper, we analysed copper slag’s feasibility and evaluate its total competence in M25 grade concrete. In this observation, a concrete mixture is applied with copper slag as a fine aggregate ranging from 0%, 20%, 40%, 60%, 80%, and 100% respectively. The strength of copper slag’s implementation is accomplished on the basis of concrete’s flexural strength, compressive strength and splitting tensile strength. From the obtained results, in concrete 40% percentage of copper slag is used as sand replacement. On 28 days, the modulus of elasticity increased up to 32%, the compressive strength increased up to 34% and flexural strength is increased to 6.2%. From this experiment, it is proved technically that replacing sand using copper slag as a fine mixture in M25 grade concrete.

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

scholarly journals Investigating the Behavior of Concrete and Mortar Reinforced with Aluminum Waste Strips

2018 ◽  
Vol 7 (4.37) ◽  
pp. 211
Author(s):  
Rawa Shakir Muwashee ◽  
Hamid Athab Al-Jameel ◽  
Qusay Abdulhameed Jabai
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Fiber Reinforced Concrete ◽  
Low Density ◽  
High Modulus ◽  
Aluminum Strip ◽  
Lower Strain ◽  
Cracks Propagation

Composite  concrete such as fiber reinforced concrete is widely used in structures because of its excellent properties such as compressive, flexural and tensile strengths and also high modulus of elasticity because it gives lower strain values under loading and too fewer cracks propagation. In this study, Aluminum strips was prepared by cutting the Coca- Cola cans as strips in concrete. The reason of using Aluminum strip is low density and good tensile strength (about 310 MPa) and also has a good ductility.  The results of this study show good improvements in compressive, tensile and  flexural strengths using 117 tested specimens for both concrete and mortar. In brief, about 22 % increment in compressive strength of Aluminum strip concrete  and flexural strength increases from 3.31 MPa to 11.20 MPa when using Aluminum strips with 2.5 % by volume of concrete. The reinforced mortar with Aluminum strips demonstrates significant increments which are 27% for compressive strength and more than 100% for both flexural and tensile strengths comparing with reference mix.  

scholarly journals Studi Eksperimental Beton Mutu Tinggi Dengan Agregat Batok Kelapa Dan Terak Baja

2021 ◽  
Vol 3 (3) ◽  
pp. 448-458
Author(s):  
Anisa Tikupadang ◽  
Herman Parung ◽  
Benny Kusuma
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Steel Slag ◽  
Coconut Shell ◽  
Crushed Stone ◽  
Split Tensile Strength ◽  
Increasing Demand ◽  
Coconut Shells

Steel slag is a waste from the steel smelting industry. Along with the increasing demand for steel, it can also cause steel waste to increase. Coconut shell is a solid waste from the rest of coconut processing. This study aims to obtain the compressive strength, split tensile strength, flexural strength, and modulus of elasticity with coarse aggregate substituted for steel slag and coconut shell, with a concrete quality of f'c 45 MPa. The results of this study that the compressive strength of concrete obtained, 100% crushed stone aggregate increased 5.213% and coconut shell substitution and steel slag increased 1.650%. The value of the split tensile strength of concrete, 100% crushed stone is 9.312% and the substitution of coconut shells and steel slag is 9.073 of the compressive strength. The value of flexural strength, 100% crushed stone is 0.827√(f'c) and the substitution of coconut shell and steel slag is 0.752 f'c from the compressive strength. The modulus of elasticity of concrete, 100% crushed stone is 24845,351 MPa and substitution of coconut shells and steel slag is 20674,005 MPa.    

scholarly journals Effect of Ading Nanocarbon Black on the Mechanical Properties of Epoxy

2014 ◽  
Vol 7 (1) ◽  
pp. 94-108
Author(s):  
Amer Hameed Majeed ◽  
Mohammed S. Hamza ◽  
Hayder Raheem Kareem
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Carbon Black ◽  
Modulus Of Elasticity ◽  
Tensile Modulus ◽  
Dispersion Method ◽  
Carbon Black Nanoparticles

The study covers the effect of nanocarbon black particles (N220) on some important mechanical properties of epoxy reinforced with it [carbon black nanoparticles]. The nanocomposites were prepared with (1 to 10 wt. %) of carbon black nanoparticles using ultrasonic wave bath machine dispersion method. The results had shown that the tensile strength , tensile modulus of elasticity, flexural strength and impact strength are improved by (24.02%,7.93%,17.3% and 6% ) respectively at 2wt % .The compressive strength and hardness are improved by (44.4%, 12%) at 4wt%.

scholarly journals Experimental investigation on engineering properties of lightweight foamed concrete (LFC) with coconut fiber addition

2018 ◽  
Vol 250 ◽  
pp. 05005
Author(s):  
Nabihah Mohd Zamzani ◽  
Azree Othuman Mydin ◽  
Abdul Naser Abdul Ghani
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Poisson’S Ratio ◽  
Splitting Tensile Strength ◽  
Poisson's Ratio ◽  
Engineering Properties ◽  
Coconut Fiber ◽  
Foamed Concrete ◽  
Coconut Fibre

In the last few years, there is emerging attention in using Lightweight Foamed Concrete (LFC) as a lightweight non-structural and semi-structural element in buildings to take advantage of its excellent insulation properties. Though, LFC has been noticed to have some disadvantages: considerable brittleness; results in low compressive and flexural strength, poor fracture toughness, poor resistance to crack propagation and low impact strength. Coconut fibre obtained from coconut husk, belonging to the family of palm fibres, is agricultural waste products obtained in the processing of coconut oil. In Malaysia, they are available in large quantities. Coconut fibre is extracted from the outer shell of a coconut. There are many general advantages of coconut fibres e.g. they are moth-proof, resistant to fungi and rot, provide excellent insulation against temperature and sound, not easily combustible, flame-retardant, unaffected by moisture and dampness, tough and durable, resilient, springs back to shape even after constant use, totally static free and easy to clean. Hence this study is intended to look into the potential of coconut fiber in enhancing the engineering properties of LFC. There are 5 engineering properties will be focused in this study which are flexural strength, splitting tensile strength, compressive strength, Poisson’s ratio and Poisson’s ratio toughness. Three densities of LFC of 800 kg/m3, 1100 kg/m3 and 1400 kg/m3 were cast and tested. The ratio of cement, sand and water used in this study was 1:1.5:0.49. Coconut fibers were used as additives at 0.12%, 0.24%, 0.36%, 0.48% and 0.60% by volume of the total mix. Test results indicated that the engineering properties of LFC strengthen with coconut fiber had increased soundly. Coconut fiber inclusion changes the post-peak response at the load-deflection curves for the samples, which modifies the failure mode and enhance the flexural strength, compressive strength and splitting tensile strength.

scholarly journals PENGARUH PERBEDAAN UKURAN KARET BAN BEKAS TERHADAP SIFAT MEKANIK

2020 ◽  
Vol 16 (1) ◽  
pp. 38-48
Author(s):  
Multilawati Nasution ◽  
Akhmad Aminnullah ◽  
Bambang Suhendro
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Construction Materials ◽  
Beam Test ◽  
Rubber Content ◽  
Tire Rubber ◽  
Synthetic Rubber ◽  
Significant Difference

ABSTRAKBan bekas sulit diurai karena salah satu bahan penyusunnya adalah karet sintetis. Ban bekas digunakan untuk kerajinan tangan, namun besar peluang penggunaan ban bekas sebagai material konstruksi. Kajian ini bertujuan untuk membedakan ukuran karet ban bekas berdasarkan lolos saringan no.#4 (4.8 mm) dan lolos saringan no.#8 (2.3mm). Objek kajian ini adalah kuat tekan dan modulus elastisitas dengan benda uji slinder (&15 cm x 30 cm), kuat lentur dengan benda uji balok (10 cm x 10 cm x 50 cm),  serta kuat tarik dengan benda uji dogbone. Salah satu penyusun mortar adalah karet ban bekas pengganti sebagian dari volume pasir. Kadar karet yang di ambil dari kajian ini adalah 0%, 20%, 40% dan 60%. Kajian ini tidak didapatkan perbedaan yang signifikansi yang besar antara penggunaan karet ban bekas lolos saringan no.#4 (4.8 mm) dan lolos saringan no.#8 (2.3mm).Kata kunci: ban bekas, kuat tarik, kuat tekan, kuat lentur, modulus elastisitasABSTRACTUsed tires are difficult to decompose because one of the constituent materials is synthetic rubber. Used tires are used for handicrafts, but there is a big chance of using used tires as construction materials. This study aims to differentiate the size of used rubber tires based on sieve No. 4 (4.8 mm) and sieve # 8 (2.3mm). The object of this research is compressive strength and modulus of elasticity with slinder test specimens (15 cm x 30 cm), flexural strength with beam test specimens (10 cm x 10 cm x 50 cm), and tensile strength with dogbone specimens. One of the compilers of the mortar is a used tire rubber which partially replaces the volume of sand. The rubber content taken from this study is 0%, 20%, 40% and 60%. There was no significant difference between this study between the use of used rubber tires that passed filter No. #4 (4.8 mm) and passed filter # 8 (2.3 mm).Keywords: used tires, tensile strength, compressive strength, flexural strength, modulus of elasticity

Sign in / Sign up

Export Citation Format

Share Document