scholarly journals Effect of Waterjet Machining Parameters on the Cut Quality of PP and PVC-U Materials Coated with Polyurethane and Acrylate Coatings

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7542
Author(s):  
Miroslav Müller ◽  
Viktor Kolář ◽  
Jan Šulc ◽  
Rajesh Kumar Mishra ◽  
Monika Hromasová ◽  
...  
Keyword(s):  
Base Material ◽  
Polymeric Materials ◽  
Traverse Speed ◽  
Sem Analysis ◽  
Kerf Width ◽  
Abrasive Waterjet ◽  
Machining Parameters ◽  
Taper Angle ◽  
Cutting Head ◽  
Cut Quality

The article focuses on the machining of polymeric materials polypropylene (PP) and un-plasticized poly vinyl chloride (PVC-U) after surface treatment with polyurethane and acrylate coatings using waterjet technology. Two types of waterjet technologies, abrasive waterjet (AWJ) and waterjet without abrasive (WJ), were used. The kerf width and its taper angle, at the inlet and outlet of the waterjet from the workpiece, were evaluated. Significant differences between AWJ and WJ technology were found. WJ technology proved to be less effective due to the creation of a nonuniform cutting gap and significant burrs. AWJ technology was shown to be more efficient, i.e., more uniform cuts were achieved compared to WJ technology, especially at a cutting head traverse speed of 50 mm·min−1. The most uniform kerf width or taper angle was achieved for PP + MOBIHEL (0.09°). The materials (PP and PVC-U) with the POLURAN coating had higher values of the taper angle of the cutting gap than the material with the MOBIHEL coating at all cutting head traverse speeds. The SEM results showed that the inappropriate cutting head traverse speed and the associated WJ technology resulted in significant destruction of the material to be cut on the underside of the cut. Delamination of the POLURAN and MOBIHEL coatings from the base material PP and PVC-U was not demonstrated by SEM analysis over the range of cutting head traverse speeds, i.e., 50 to 1000 mm·min−1.

scholarly journals Investigation of the Effects of Machining Parameters on Material Removal Rate in Abrasive Waterjet Turning

2014 ◽  
Vol 6 ◽  
pp. 624203 ◽  
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Flow Rate ◽  
Material Removal Rate ◽  
Rotational Speed ◽  
Material Removal ◽  
Removal Rate ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cutting Head

The effects of the main operational machining parameters on the material removal rate (MRR) in abrasive waterjet turning (AWJT) are presented in this paper using a statistical approach. The five most common machining parameters such as water pressure, abrasive mass flow rate, cutting head traverse speed, workpiece rotational speed, and depth of cut have been put into a five-level central composite rotatable experimental design (CCRD). The main effects of parameters and the interaction among them were analyzed by means of the analysis of variance (ANOVA) and the response surfaces for MRR were obtained fitting a second-order polynomial function. It has been found that depth of cut and cutting head traverse speed are the most influential parameters, whereas the rotational speed is insignificant. In addition, the investigations show that interactions between traverse speed and pressure, abrasive mass flow rate and depth of cut, and pressure and depth of cut are significant on MRR. This result advances the AWJT state of the art. A complete model discussion has been reported drawing interesting considerations on the AWJT process characterising phenomena, where parameters interactions play a fundamental role.

scholarly journals Impacts of Traverse Speed and Material Thickness on Abrasive Waterjet Contour Cutting of Austenitic Stainless Steel AISI 304L

2021 ◽  
Vol 11 (11) ◽  
pp. 4925
Author(s):  
Jennifer Milaor Llanto ◽  
Majid Tolouei-Rad ◽  
Ana Vafadar ◽  
Muhammad Aamir
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Taper Angle ◽  
Material Thickness ◽  
Abrasive Waterjet Machining ◽  
Kerf Taper ◽  
Waterjet Machining

Abrasive water jet machining is a proficient alternative for cutting difficult-to-machine materials with complex geometries, such as austenitic stainless steel 304L (AISI304L). However, due to differences in machining responses for varied material conditions, the abrasive waterjet machining experiences challenges including kerf geometric inaccuracy and low material removal rate. In this study, an abrasive waterjet machining is employed to perform contour cutting of different profiles to investigate the impacts of traverse speed and material thickness in achieving lower kerf taper angle and higher material removal rate. Based on experimental investigation, a trend of decreasing the level of traverse speed and material thickness that results in minimum kerf taper angle values of 0.825° for machining curvature profile and 0.916° for line profiles has been observed. In addition, higher traverse speed and material thickness achieved higher material removal rate in cutting different curvature radii and lengths in line profiles with obtained values of 769.50 mm3/min and 751.5 mm3/min, accordingly. The analysis of variance revealed that material thickness had a significant impact on kerf taper angle and material removal rate, contributing within the range of 69–91% and 62–69%, respectively. In contrast, traverse speed was the least factor measuring within the range of 5–18% for kerf taper angle and 27–36% for material removal rate.

EXPERIMENTAL STUDY OF SURFACE ROUGHNESS AND TAPER ANGLE IN ABRASIVE WATER JET MACHINING OF 7075 ALUMINUM COMPOSITE USING RESPONSE SURFACE METHODOLOGY

2019 ◽  
Vol 27 (03) ◽  
pp. 1950112 ◽  
Author(s):  
A. SHANMUGAM ◽  
K. KRISHNAMURTHY ◽  
T. MOHANRAJ
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Water Pressure ◽  
Traverse Speed ◽  
Standoff Distance ◽  
Abrasive Waterjet ◽  
Machined Surface ◽  
Taper Angle

Surface roughness and taper angle of an abrasive waterjet machined surface of 7075 Aluminum metal matrix composite were deliberately studied. Response surface methodology design of experiments and analysis of variance were used to design the experiments and to identify the effect of process parameters on surface roughness and taper angle. The jet traverse speed and jet pressure were the most significant process parameters which influence the surface roughness and taper angle, respectively. Increasing the pressure and jet traverse speed results in increasing the surface roughness and taper angle. At the same time, decreasing the standoff distance and jet traverse speed possibly enhances both the responses. The optimal process parameters of 1[Formula: see text]mm as standoff distance, 192[Formula: see text]MPa as water pressure and 30[Formula: see text]mm[Formula: see text]min[Formula: see text] as jet traverse speed were identified to obtain the minimum value of surface roughness and taper angle. Based on the optimal parameters, the confirmation test was conducted. The mathematical equation was obtained from the experimental data using regression analysis; it was observed that the error was less than 5% of the experimentally measured values.

Experimental investigations on high precision abrasive waterjet cutting of natural fibre reinforced nano clay filled green composites

2020 ◽  
pp. 152808372094296
Author(s):  
D Rajamani ◽  
E Balasubramanian ◽  
G Dilli Babu ◽  
K Ananthakumar
Keyword(s):  
Composite Laminates ◽  
Removal Rate ◽  
Traverse Speed ◽  
Natural Fibre ◽  
Abrasive Waterjet ◽  
Experimental Investigations ◽  
Waterjet Cutting ◽  
Abrasive Waterjet Cutting ◽  
Nano Clay ◽  
Cut Quality

The present investigation focused on abrasive waterjet cutting (AWJC) of natural fibre reinforced nano clay filled polyester composites with the objectives of maximizing material removal rate ( MRR) and minimizing the kerf taper ( KT) and surface roughness ( Ra). The influence of nano clay addition, traverse speed (TS), jet pressure (JP) and stand-off distance (SOD) on the AWJC characteristics of fabricated composite laminates are investigated. The natural fibre reinforced composite (NFRC) laminates are fabricated through hand lay-up technique through varying the wt% of nano clay fillers (0, 1 and 2). The AWJC experiments are planned and rigorous experiments were performed by adopting box-behnken design approach. The relative consequence of process variables on response features and quadratic regression models were assessed through analysis of variance (ANOVA). Further, multiple response optimization is carried out using statistical desirability technique to enhance the cut quality characteristics. The optimal AWJC parameters such as JP of 316.24 MPa, SOD of 2 mm and TS of 304.24 mm/min with 1.15 wt% of nano clay addition are determined. Microstructure of cut surface is examined to ascertain the morphological behaviour of AWJC surfaces with different processing conditions.

MULTI-RESPONSE OPTIMIZATION ON ABRASIVE WATERJET MACHINING OF GLASS FIBER REINFORCED PLASTICS USING TAGUCHI METHOD COUPLED WITH TOPSIS

2021 ◽  
Author(s):  
A. SHANMUGAM ◽  
T. MOHANRAJ ◽  
K. KRISHNAMURTHY ◽  
ALI KAYA GUR
Keyword(s):  
Glass Fiber ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Taper Angle ◽  
Reinforced Plastics ◽  
Abrasive Waterjet Machining ◽  
Glass Fiber Reinforced ◽  
Waterjet Machining ◽  
Response Optimization ◽  
Fiber Reinforced Plastics

This work aims to perform the multi-response optimization for abrasive waterjet machining (AWJM) of glass fiber reinforced plastics (GFRP). The experiments were conducted with AWJM factors like pressure (P), traverse speed (TS), and standoff distance (SOD) at three levels. Taguchi’s L9 orthogonal array (OA) was used to design the experiments. The influence of control factors was evaluated by measuring the surface roughness and taper angle while cutting GFRP. The optimum parameter for an individual response was obtained through Taguchi’s [Formula: see text]/[Formula: see text] and multi-response optimization was performed with TOPSIS. From TOPSIS, the optimal parameter of the pressure of 200 MPa, standoff distance (SOD) of 1.5[Formula: see text]mm, and traverse speed (TS) of 25[Formula: see text]mm/min were found. After optimization, the taper angle was decreased by 1.41%. The influence of cutting variables on the responses was statistically analyzed through analysis of variance. It was observed that the pressure has a significant effect on multi-response characteristics and a contribution of 85.90%. After, AWJM, the surface was examined using SEM analysis and found the deformation and pull-out of fibers.

Surface Waviness in Abrasive Waterjet Offset-Mode Turning

2014 ◽  
Vol 599-601 ◽  
pp. 555-559
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Surface Waviness ◽  
Cutting Head

In this paper, surface waviness quality in abrasive waterjet offset-mode turning has been studied regarding variations of some process parameters. Influence of five main operational parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut on surface waviness of turned parts have been investigated using statistical approach. Second order regression model presented for surface waviness. The model accuracy was verified by comparing with experimental data. It found that abrasive mass flow rate, cutting head traverse speed and DOC are the most influential parameters while water pressure and workpiece rotational speed show lesser effectiveness.

Modeling of Surface Waviness in Abrasive Waterjet Offset-Mode Turning

2014 ◽  
Vol 621 ◽  
pp. 202-207
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Surface Waviness ◽  
Cutting Head

In this paper, surface waviness produced by turning aluminum parts with abrasive waterjet has been studied regarding changes in some process parameters. Effect of five major parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut have been investigated using analysis of variances. Second order regression model presented forwaviness.The validity of the model wasconfirmed bycomparing with experimental data. It found thatabrasive mass flow rate, cutting head traverse speed and DOC are the most influencing parameters while water pressure and workpiece rotational speed show lesser effectiveness.

scholarly journals Impacts of traverse speed and material thickness in abrasive waterjet contour cutting of Austenitic stainless steel AISI 304L

2021 ◽  
Author(s):  
Jennifer llanto ◽  
Majid Tolouei-Rad ◽  
Ana Vafadar ◽  
Muhammad Aamir
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Taper Angle ◽  
Material Thickness ◽  
Kerf Taper

Abstract Austenitic stainless steel 304L (AISI304L), of varied thickness, is widely used in the fabrication industry and in many cases, it requires contour machining for achieving intricate profiles. Abrasive water jet machine is a proficient alternative for machining difficult-to-cut, reflective, conductive, and heat-sensitive materials such as austenitic stainless steel with complex geometries. However, due to differences in machining responses for varied material conditions, the abrasive waterjet machine experiences challenges such as kerf geometric inaccuracy and low material removal rate. In this study, an abrasive waterjet machine is employed to perform contour cutting of different profiles to investigate the impacts of traverse speed and material thickness in achieving a lower kerf taper angle and higher material removal rate. Experimental results show that all profiles encountered a similar trend of obtaining higher kerf taper angle and material removal rate as traverse speed increased. Analysis of variance revealed that material thickness denotes a more significant impact to kerf taper angle and material removal rate with a contribution within the range of 69%-91% and 62-69% respectively; whereas traverse speed indicates the least contributing factor within the range of 5%-18% in kerf taper angle and 27%-36% for material removal rate.

scholarly journals Abrasive Waterjet (AWJ) Forces—Potential Indicators of Machining Quality

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3309
Author(s):  
Libor M. Hlaváč ◽  
Massimiliano P. G. Annoni ◽  
Irena M. Hlaváčová ◽  
Francesco Arleo ◽  
Francesco Viganò ◽  
...  
Keyword(s):  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Speed Ratio ◽  
Machining Processes ◽  
Measuring Device ◽  
Cutting Head ◽  
Wear Ratio ◽  
Tilting Angle ◽  
Declination Angle ◽  
Awj Cutting

The necessity of monitoring the abrasive waterjet (AWJ) processes increases with the spreading of this tool into the machining processes. The forces produced on the workpiece during the abrasive waterjet machining can yield some valuable information. Therefore, a special waterjet-force measuring device designed and produced in the past has been used for the presented research. It was tested during the AWJ cutting processes, because they are the most common and the best described up-to-date AWJ applications. Deep studies of both the cutting process and the respective force signals led to the decision that the most appropriate indication factor is the tangential-to-normal force ratio (TNR). Three theorems concerning the TNR were formulated and investigated. The first theorem states that the TNR strongly depends on the actual-to-limit traverse speed ratio. The second theorem claims that the TNR relates to the cutting-to-deformation wear ratio inside the kerf. The third theorem states that the TNR value changes when the cutting head and the respective jet axis are tilted so that a part of the jet velocity vector projects into the traverse speed direction. It is assumed that the cutting-to-deformation wear ratio increases in a certain range of tilting angles of the cutting head. This theorem is supported by measured data and can be utilized in practice for the development of a new method for the monitoring of the abrasive waterjet cutting operations. Comparing the tilted and the non-tilted jet, we detected the increase of the TNR average value from 1.28 ± 0.16 (determined for the declination angle 20° and the respective tilting angle 10°) up to 2.02 ± 0.25 (for the declination angle 30° and the respective tilting angle of 15°). This finding supports the previously predicted and published assumptions that the tilting of the cutting head enables an increase of the cutting wear mode inside the forming kerf, making the process more efficient.

A New Variable Feedrate CNC Interpolator for Abrasive Waterjet System

2009 ◽  
Vol 626-627 ◽  
pp. 339-344
Author(s):  
Wei Xiao Tang ◽  
X.D. Zhang ◽  
L. Wang
Keyword(s):  
Experimental Data ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Free Form ◽  
Jet Lag ◽  
Taper Angle ◽  
Kerf Taper ◽  
Pythagorean Hodographs ◽  
Ph Curve ◽  
Cut Surface

It is becoming general that the contour of part is defined with free-form curves for abrasive waterjet cutting. In this paper, the effect of the traverse speed on cut surface quality is discussed. After that, the free-form Pythagorean Hodographs (PH) curve is defined and its main characteristics are discussed. A new CNC interpolator capable of driving the nozzle along the PH curves at the feedrate adaptable of the curvature of the contour is presented. The taper shape or jet lag can be minimized with it through the variation of the traverse speed. Experimental data indicate that a decrease of about 58 per cent in kerf taper angle can be obtained under a given condition.

Sign in / Sign up

Export Citation Format

Share Document