scholarly journals Effect of Precipitation Temperature on the Properties of Cellulose Ultrafiltration Membranes Prepared via Immersion Precipitation with Ionic Liquid as Solvent

Membranes ◽  
2018 ◽  
Vol 8 (4) ◽  
pp. 87 ◽  
Author(s):  
Daria Nevstrueva ◽  
Arto Pihlajamäki ◽  
Juha Nikkola ◽  
Mika Mänttäri
Keyword(s):  
Ionic Liquid ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Bath Temperature ◽  
Liquid Solution ◽  
Coagulation Bath ◽  
Fouling Resistance ◽  
Ultrafiltration Membranes ◽  
Coagulation Bath Temperature

Supported cellulose ultrafiltration membranes are cast from a cellulose-ionic liquid solution by the immersion precipitation technique. The effects of coagulation bath temperature and polymer concentration in the casting solution on the membrane morphology, wettability, pure water flux, molecular weight cut-off, and fouling resistance are studied. Scanning electron microscopy, contact angle measurements, atomic force microscopy, and filtration experiments are carried out in order to characterise the obtained ultrafiltration cellulose membranes. The results show the effect of coagulation bath temperature and polymer concentration on the surface morphology and properties of cellulose ultrafiltration membranes. Optimisation of the two parameters leads to the creation of dense membranes with good pure water fluxes and proven fouling resistance towards humic acid water solutions.

Preparation and Characterizations of Polysulfone Flat Ultrafiltration Membranes

2011 ◽  
Vol 418-420 ◽  
pp. 169-172
Author(s):  
Shan Zhang ◽  
Zhen Liu
Keyword(s):  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Egg Rejection ◽  
Evaporation Time ◽  
Ultrafiltration Membranes ◽  
Pure Water Flux ◽  
Coagulation Bath Temperature

The Polysulfone Flat ultrafiltration membranes were prepared with dimethylacetamide (DMAc) as solvent and polyvinypyrrolidone (PVP) as pore forming additive. Performance of PSF membrane such as pure water flux, albumin egg rejection were investigated. In addition, the same investigations were conducted with different coagulation bath temperature and evaporation time. The results show that there were a maximum of pure water flux and a minimum of the retention of Albumin when PVP content reach 14%.

scholarly journals Study of polyamide-6 hollow fiber membranes prepared via a thermally induced phase-separation method

e-Polymers ◽  
2010 ◽  
Vol 10 (1) ◽  
Author(s):  
Zhao-Hui Jiang ◽  
Chang-Fa Xiao ◽  
Xiao-Yu Hu
Keyword(s):  
Hollow Fiber ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Hollow Fiber Membranes ◽  
Fiber Membranes ◽  
Pure Water Flux ◽  
Coagulation Bath Temperature

AbstractHollow fiber membranes of polyamide-6(PA6) with porous structure were prepared by a thermally induced phase-separation method. N-Ethyl-o/p-toluene sulfonamide was chosen as diluent. On the basis of scanning electron microscopy (SEM) images, porosity, bubble point pore diameter and pure water flux, the influential factors including polymer concentration, coagulation bath temperature, post-stretching were investigated. The results indicate that with the increasing of PA6 concentration ‘slit-shaped’ pores in inner surfaces and cellular structure in cross-sections disappear, correspondingly, the properties of membranes such as porosity and pure water flux become poor. As the coagulation bath temperature varied from 20 °C to 50°C, the pure water flux of membranes is improved from 136 to 244 L·m-2·h-1. Post-stretching make the ‘interfacial micro-pores’ expand due to ‘stress concentration’ phenomenon, thus changing the structure and improving the properties of membranes. PA6 hollow fiber membranes with rational structure and high performance could be obtained by altering polymer concentration, coagulation bath temperature and post-stretching.

Effect of Additive on the Performance of PVDF Membrane via Non-Solvent Induced Phase Separation

2014 ◽  
Vol 789 ◽  
pp. 240-248 ◽  
Author(s):  
Xiao Hui Cao ◽  
Ming Qiu ◽  
Ai Wen Qin ◽  
Chun Ju He ◽  
Hai Feng Wang
Keyword(s):  
Tensile Strength ◽  
Phase Separation ◽  
Propylene Glycol ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Breaking Elongation ◽  
Coagulation Bath Temperature

Poly (vinylidene fluoride) membranes were prepared from the ternary mixture of PVDF/ 1, 2 - propylene glycol/dimethylacetamidevianon-solvent induced phase separation (NIPS). The effect of the addition of the 1, 2 - propylene glycol content, the Coagulation Bath Temperature and the concentration of PVDF on the performance and structure of the PVDF membranes was studied in the present investigation.The results showed that with increasing polymer concentration, the mechanical strength increased,and the structure of membrane changed from finger-like macro-voids structureto sponge-like structure.It was found that water flux, breaking elongation and tensile strength of the membrane increased with increasing 1, 2 - propylene glycol content, when the content reached 41wt.%, the water flux reaches a maximum.The morphology of PVDF can be improved by the addition of 1, 2 - propylene glycol, which was changed from finger-like structure to sponge-like structure. And the dense skin layer of PVDF membranes became thicker with increasing 1, 2 – propyleneglycol. The tensile strength decreasedfrom 3.3 to 2.1MPa, breaking elongation decreased from 315% to 280% andthe pure water flux increased from 91 to 909 L·m-2·h-1. as the coagulation bath temperature (CBT) decreased from 30°C to 5°C.With this condition, the sponge-like hollow fiber membrane hassuccessfully spun.

Preparation and Performance of Polysulfone Hollow Fiber Ultrafiltration Membranes

2013 ◽  
Vol 457-458 ◽  
pp. 309-312 ◽  
Author(s):  
Yang Bai ◽  
Zhen Liu ◽  
Dao Bao Sun
Keyword(s):  
Hollow Fiber ◽  
High Performance ◽  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Membrane Structures ◽  
Ultrafiltration Membranes ◽  
Pure Water Flux ◽  
And Performance

Polysulfone (PSF) hollow fiber ultrafiltration membranes were successfully prepared by dry-wet spinning technology. Dimethylacetamide (DMAC) was used as a solvent, water was used as bore liquid and coagulation bath, polyvinylpyrrolidone (PVP) was used as polymeric additive. The effects of spinning conditions on membrane structures and properties were investigated in present study. The results indicated that with the increase of PVP concentration, pure water flux increased and developed finger-like pores were formed. High coagulation bath temperature restricted pure water flux, 30°C was the best for the preparation of high-performance ultrafiltration membranes. When the air length was 11cm, the membrane comprehensive performance was the best.

scholarly journals Polymer Concentration and Solvent Variation Correlation with the Morphology and Water Filtration Analysis of Polyether Sulfone Microfiltration Membrane

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Muhammad Azeem U. R. Alvi ◽  
Muhammad Waqas Khalid ◽  
Nasir M. Ahmad ◽  
Muhammad Bilal K. Niazi ◽  
Muhammad Nabeel Anwar ◽  
...  
Keyword(s):  
Polymer Concentration ◽  
Water Flux ◽  
Bath Temperature ◽  
Membrane Resistance ◽  
Precipitation Method ◽  
Coagulation Bath ◽  
Membrane Formation ◽  
Polyether Sulfone ◽  
Subsequent Effect ◽  
Coagulation Bath Temperature

Microfiltration flat sheet membranes of polyether sulfone (PES) were fabricated by incorporating varying concentrations of polymer and investigated the influence of substituting solvents. The membranes were prepared via immersion precipitation method. Different solvents that included NMP (N-methyl-2-pyrrolidone), DMF (dimethylformamide), and THF (tetrahydrofuran) were used to analyse their effect on the performance and morphology of the prepared membranes. Two different coagulation bath temperatures were used to investigate the kinetics of membrane formation and subsequent effect on membrane performance. The maximum water flux of 141 ml/cm2.h was observed using 21% of PES concentration in NMP + THF cosolvent system. The highest tensile strength of 29.15 MPa was observed using membrane prepared with 21% PES concentration in NMP as solvent and coagulation bath temperature of 25°C. The highest hydraulic membrane resistance was reported for membrane prepared with 21% PES concentration in NMP as solvent. Moreover, the lowest contact angle of 67° was observed for membrane prepared with 15% of PES concentration in NMP as solvent with coagulation bath temperature of 28°C. Furthermore, the Hansen solubility parameter was used to study the effect on the thermodynamics of membrane formation and found to be in good correlation with experimental observation and approach in the present work.

scholarly journals Effect of sonochemical synthesized TiO2 nanoparticles and coagulation bath temperature on morphology, thermal stability and pure water flux of asymmetric cellulose acetate membranes prepared via phase inversion method

2012 ◽  
Vol 18 (3) ◽  
pp. 385-398 ◽  
Author(s):  
Reza Abedini ◽  
Mahmoud Mousavi ◽  
Reza Aminzadeh
Keyword(s):  
Thermal Stability ◽  
Tio2 Nanoparticles ◽  
Phase Inversion ◽  
Pure Water ◽  
Water Flux ◽  
Composite Membranes ◽  
Bath Temperature ◽  
Coagulation Bath ◽  
Pure Water Flux ◽  
Coagulation Bath Temperature

In this study, asymmetric pure CA and CA/ TiO2 composite membranes were prepared via phase inversion by dispersing TiO2 nanopaticles in the CA casting solutions induced by immersion precipitation in water coagulation bath. TiO2 nanoparticles, which were synthesized by the sonochemical method, were added into the casting solution with different concentrations. Effects of TiO2 nanoparticles concentration (0 wt. %, 5wt.%, 10wt.%, 15wt.%, 20wt.% and 25wt.%) and coagulation bath temperature (CBT= 25?C, 50?C and 75?C) on morphology, thermal stability and pure water flux (PWF) of the prepared membranes were studied and discussed. Increasing TiO2 concentration in the casting solution film along with higher CBT resulted in increasing the membrane thickness, water content (WC), membrane porosity and pure water flux (PWF), also these changes facilitate macrovoids formation. Thermal gravimetric analysis (TGA) shows that thermal stability of the composite membranes were improved by the addition of TiO2 nanopaticles. Also TGA results indicated that increasing CBT in each TiO2 concentration leads to the decreasing of decomposition temperature (Td) of hybrid membranes.

Influence of the Coagulation-Bath Temperature on Membrane Formation Mechanism and Properties of PVDF/TA-ATP Hybrid Membrane

2015 ◽  
Vol 713-715 ◽  
pp. 2723-2726
Author(s):  
Yue Rong Shi ◽  
Gui Fang Zhang ◽  
Xing Tian Liu ◽  
Xue Tao Tian ◽  
Yi Ping Zhao ◽  
...  
Keyword(s):  
Formation Mechanism ◽  
Vinylidene Fluoride ◽  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Time Domain Reflectometry ◽  
Coagulation Bath ◽  
Membrane Formation ◽  
Water Permeation ◽  
Ultrasonic Time

In this study, poly (vinylidene fluoride) (PVDF) hybrid membranes were prepared from polymeric blend of PVDF/tannic acid (TA)-Attapulgite (ATP)/PEG system via phase inversion induced by immersion precipitation in water coagulation bath. The membrane formation mechanism of PVDF/TA-ATP/PEG casting solutions in water bath thermodynamics at different temperatures and the process of membrane formation were investigated via cloud point determination and ultrasonic time-domain reflectometry (UTDR). The structures and properties of the membrane were characterized by scanning electron microscopy (SEM), and water permeation experiment, respectively. It was found that the rate of precipitation controlled by the Coagulation-Bath thermodynamics. With the coagulation temperature increasing, the gelation line was moved to non-solvent axis and the pure water flux were decreased.

A Novel Polyethersulfone Flat Sheet Membrane Prepared from a Lower Critical Solution Temperature System

2012 ◽  
Vol 538-541 ◽  
pp. 29-32
Author(s):  
Jing Diao ◽  
Jian Feng Xu ◽  
Song Tao Li ◽  
Xiao Hui Cao ◽  
Chun Yi Liu ◽  
...  
Keyword(s):  
Lower Critical Solution Temperature ◽  
Pure Water ◽  
Water Flux ◽  
Bath Temperature ◽  
Solution Temperature ◽  
Coagulation Bath ◽  
Sem Images ◽  
Critical Solution Temperature ◽  
Flat Sheet ◽  
Flat Sheet Membrane

Polyethersulfone (PES) flat sheet membranes were prepared via phase inversion induced by immersion precipitation from a novel lower critical solution temperature (LCST) system containing PES, 1-butanol and N, N-dimethylacetamide. And the effect of coagulation bath temperature on the properties and structure of PES membranes were investigated. The results show that the pure water flux increases and the tensile strength decreases as the coagulation temperature increases form 20°C to 50°C. Besides, the SEM images shows that all of the membranes prepared from a LCST system at different CBT own sponge-like structures.

Sign in / Sign up

Export Citation Format

Share Document