Recent Mitigation Strategies on Membrane Fouling for Oily Wastewater Treatment

The discharge of massive amounts of oily wastewater has become one of the major concerns among the scientific community. Membrane filtration has been one of the most used methods of treating oily wastewater due to its stability, convenience handling, and durability. However, the continuous occurrence of membrane fouling aggravates the membrane’s performance efficiency. Membrane fouling can be defined as the accumulation of various materials in the pores or surface of the membrane that affect the permeate’s quantity and quality. Many aspects of fouling have been reviewed, but recent methods for fouling reduction in oily wastewater have not been explored and discussed sufficiently. This review highlights the mitigation strategies to reduce membrane fouling from oily wastewater. We first review the membrane technology principle for oily wastewater treatment, followed by a discussion on different fouling mechanisms of inorganic fouling, organic fouling, biological fouling, and colloidal fouling for better understanding and prevention of membrane fouling. Recent mitigation strategies to reduce fouling caused by oily wastewater treatment are also discussed.

A simplified method for the deposition rate assessment on the vanes of a multistage axial-flow compressor

Gas turbine particle ingestion may lead to the deposition of contaminants in the compressor section, inducing the performance losses of the whole engine. The economic losses derived from this issue push great interest in the investigation of such a phenomenon from a numerical and experimental standpoint. This paper describes a quantitative approach to predict particle deposition on the vanes of an axial compressor starting from the flow field obtained employing CFD simulations. The results are then compared to the experiments performed on the Allison 250 C18 compressor unit subject to particle ingestion under controlled conditions. The results derived from the experimental and numerical investigations are presented, providing insight into the mass deposited on the vanes and the corresponding zones most affected by the particle deposition issue. The numerical model showed good agreement in the estimation of the predicted values of the deposited mass and the corresponding patterns through the compressor stages. The low-complexity approach proposed here, helps the designer to predict the contamination of the stationary rows starting from a simple set of single-phase numerical results. Furthermore, with the implementation of this approach into the design path, the designer could reduce the impact of fouling, looking at the effects of their solutions under the fouling-reduction light.

Organo-Functionalization: An Effective Method in Enhancing the Separation and Antifouling Performance of Thin-Film Nanocomposite Membranes by Improving the Uniform Dispersion of Palygorskite Nanoparticles

Recently, palygorskite (Pal) has become a promising new membrane additive in flux enhancement and fouling reduction, which is an environmentally friendly nanoclay material under the 2:1 layer composition with 1D tubular structure. However, the aggregation of Pal due to the intermolecular forces is still an obstacle to be solved in improving membrane performance. Herein, Pal nanoparticles were chemically modified by KH550 to weaken the aggregation and improve the dispersibility, and then incorporated into the organic phase to prepare thin-film nanocomposite (TFN) membranes. The results showed that the organo-functionalization could effectively improve the membrane hydrophilicity and dispersion of Pal nanoparticles in the polyamide layer, which contributed to the enhanced water flux (from 25 to 38 L/m2·h), unchanged salt rejection (98.0%) and better antifouling capacity (91% flux recovery rate), which suggested that the organo-functionalization of nanoparticles was an efficient method in further enhancing membrane performance

Surface Adsorption of the Cancer Biomarker Lysophosphatidic Acid in Serum Studied by Acoustic Wave Biosensor

The thickness shear mode acoustic wave device is of interest for the sensing of biomarkers for diseases in various biological fluids, but suffers from the issue of non-specific adsorption of compounds other than those of interest to the electrode surface, thus affecting the device’s output. The aim of this present study was to determine the level of non-specific adsorption on gold electrodes from serum samples with added ovarian cancer biomarker lysophosphatidic acid in the presence of a surface anti-fouling layer. The latter was an oligoethylene molecule with thiol group for attachment to the electrode surface. It was found that the anti-fouling layer had a minimal effect on the level of both adsorption of components from serum and the marker. This result stands in sharp contrast to the analogous monolayer employed for anti-fouling reduction on silica.

Membrane Fouling Controlled by Adjustment of Biological Treatment Parameters in Step-Aerating MBR

A promising solution for membrane fouling reduction in membrane bioreactors (MBRs) could be the adjustment of operating parameters of the MBR, such as hydraulic retention time (HRT), food/microorganisms (F/M) loading and dissolved oxygen (DO) concentration, aiming to modify the sludge morphology to the direction of improvement of the membrane filtration. In this work, these parameters were investigated in a step-aerating pilot MBR that treated municipal wastewater, in order to control the filamentous population. When F/M loading in the first aeration tank (AT1) was ≤0.65 ± 0.2 g COD/g MLSS/d at 20 ± 3 °C, DO = 2.5 ± 0.1 mg/L and HRT = 1.6 h, the filamentous bacteria were controlled effectively at a moderate filament index of 1.5–3. The moderate population of filamentous bacteria improved the membrane performance, leading to low transmembrane pressure (TMP) at values ≤2 kPa for a great period, while at the control MBR the TMP gradually increased reaching 14 kPa. Soluble microbial products (SMP), were also maintained at low concentrations, contributing additionally to the reduction of ΤΜP. Finally, the step-aerating MBR process and the selected imposed operating conditions of HRT, F/M and DO improved the MBR performance in terms of fouling control, facilitating its future wider application.