scholarly journals The Influence of Cooling Rate on Microstructure and Mechanical Properties of AlSi9Cu3

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 186
Author(s):  
Matic Žbontar ◽  
Mitja Petrič ◽  
Primož Mrvar
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Cooling Rate ◽  
Die Casting ◽  
Cooling Rates ◽  
Technological Practice ◽  
Pressure Die Casting ◽  
Compressive Tests ◽  
Solidification Of Metal

The aim of this study was to determine the correlation between the size and the distribution of microstructural constituents and their cooling rate, as well as the correlation between the mechanical properties and the cooling rate of AlSi9Cu3 aluminum alloy when cast in high-pressure die casting (HPDC) conditions. In other words, the ultimate goal of the research was to determine the mechanical properties for a casting at different cooling rates. Castings with different wall thicknesses were chosen, and different cooling rates were assumed for each one. Castings from industrial technological practice were systematically chosen, and probes were extracted from those castings for the characterization of their mechanical properties. Special non-standard cylinders were created on which compressive tests were carried out. The uniqueness of this research lies in the fact that the diameters of the designed cylinders were in direct correlation to the actual wall thickness of the castings. This is important because the solidification of metal in the die cavity is complex, in that the cooling rates are higher on the surface of the casting than in the center. Local in-casting cooling rates were determined using numerical simulations. It was discovered that with increasing cooling rates from 60 K/s to 125 K/s the values for strength at 5% deformation increased on average from 261 MPa to 335 MPa.

scholarly journals On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 wt%Si alloy

2020 ◽  
Vol 30 (2) ◽  
pp. 221-228
Author(s):  
Xiangyi Jiao ◽  
Chaofeng Liu ◽  
Jun Wang ◽  
Zhipeng Guo ◽  
Junyou Wang ◽  
...  
Keyword(s):  
High Pressure ◽  
Die Casting ◽  
High Pressure Die Casting ◽  
Pressure Die Casting

Effect of Excess Mg on the Microstructure and Mechanical Properties of Al-Mg2Si High Pressure Die Casting Alloys

2013 ◽  
Vol 765 ◽  
pp. 64-68 ◽  
Author(s):  
Feng Yan ◽  
Shou Xun Ji ◽  
Zhong Yun Fan
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Mechanical Performance ◽  
Eutectic Reaction ◽  
Die Casting ◽  
High Strength ◽  
Primary Phase ◽  
High Pressure Die Casting ◽  
Excess Mg ◽  
Pressure Die Casting

In this work we found that the addition of excess Mg can significantly improve the mechanical properties of pseudo-binary Al-Mg2Si alloys after high pressure die casting (HPDC). Al-8Mg2Si-6Mg alloy offered an excellent combination of high strength and reasonable ductility. Excess Mg lowers the Mg2Si content in the eutectic reaction and promotes the formation of Mg2Si as the primary phase, and this is believed to be the origin of improved mechanical performance.

Rheocasting of Al-Cu Alloy A201 with Different Silver Contents

2008 ◽  
Vol 141-143 ◽  
pp. 151-156 ◽  
Author(s):  
E.P. Masuku ◽  
Gonasagren Govender ◽  
L. Ivanchev ◽  
Heinrich Möller
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Grain Boundaries ◽  
Die Casting ◽  
Solution Treatment ◽  
Cast Material ◽  
High Pressure Die Casting ◽  
Cu Alloy ◽  
Pressure Die Casting ◽  
Better Than

Rheocasting of alloys A206 and A201 was investigated in this study. Conical bars with different silver contents were produced using CSIR rheoprocess technology, together with high pressure die casting. The results showed that addition of Ag to alloy A206 increased the mechanical properties of the alloy. However, the addition of Ag also resulted in Cu-rich phases to precipitate at the grain boundaries of the as-cast material. The solution treatment used in this study was unable to dissolve all of this phase, especially in the 1.12%Ag-containing alloy. This resulted in slightly decreased mechanical properties compared to the 0.63%Ag-containing alloy. The T6 mechanical properties (strength and elongation) obtained in this study for rheocast A206 and A201 are better than those reported for permanent mould castings of alloy A206 and A201.

Microstructure and Mechanical Properties of Low Pressure Die Cast AM50 Magnesium Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 167-170 ◽  
Author(s):  
Li Ming Peng ◽  
Peng Huai Fu ◽  
Hai Yan Jiang ◽  
Chun Quan Zhai
Keyword(s):  
Mechanical Properties ◽  
High Pressure ◽  
Die Casting ◽  
Low Pressure ◽  
Microstructure And Mechanical Properties ◽  
Heat Treated ◽  
Die Cast ◽  
Second Phases ◽  
Am50 Alloy ◽  
Pressure Die Casting

Compact AM50 alloy components were cast by Low Pressure Die Casting (LPDC) process. The microstructure and mechanical properties of cast components were investigated under as-cast and heat treated states. It was found that the microstructure of LPDC AM50 is composed of α-Mg and second phases - Mg17Al12 and Al8Mn5. Compared with Gravity die casting, LPDC AM50 alloy had much coarser grains and higher density, with smaller sizes and less content of second phases. The density of AM50 alloy by LPDC process was ρ=1.7836g/cm3, with increase of 0.45% based on Gravity die casting and much more increase compared with high pressure die casting. The as-cast mechanical properties by LPDC process were: σ0.2=57.8Mpa, σb=192.3Mpa, δ=8.7%. These of Gravity die casting were: σ0.2=53Mpa, σb=173.4Mpa, δ=8.1%. UTS in LPDC increased about 20MPa, with better YTS and Elongation. Compared with that of high pressure die cast AM50, the YTS of LPDC was much lower, with comparable UTS and Elongation. The mechanical properties of the heat treated AM50 alloy were still in the same level of as-cast state. AM50 alloy by LPDC process is not necessary subjected to tempering treatment.

Sign in / Sign up

Export Citation Format

Share Document