scholarly journals Emerging Trends in Single Point Incremental Sheet Forming of Lightweight Metals

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1188
Author(s):  
Tomasz Trzepieciński ◽  
Valentin Oleksik ◽  
Tomaž Pepelnjak ◽  
Sherwan Mohammed Najm ◽  
Imre Paniti ◽  
...  
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
High Strength ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Process Conditions ◽  
Lightweight Materials ◽  
Ultrasonic Assisted ◽  
Lightweight Metals

Lightweight materials, such as titanium alloys, magnesium alloys, and aluminium alloys, are characterised by unusual combinations of high strength, corrosion resistance, and low weight. However, some of the grades of these alloys exhibit poor formability at room temperature, which limits their application in sheet metal-forming processes. Lightweight materials are used extensively in the automobile and aerospace industries, leading to increasing demands for advanced forming technologies. This article presents a brief overview of state-of-the-art methods of incremental sheet forming (ISF) for lightweight materials with a special emphasis on the research published in 2015–2021. First, a review of the incremental forming method is provided. Next, the effect of the process conditions (i.e., forming tool, forming path, forming parameters) on the surface finish of drawpieces, geometric accuracy, and process formability of the sheet metals in conventional ISF and thermally-assisted ISF variants are considered. Special attention is given to a review of the effects of contact conditions between the tool and sheet metal on material deformation. The previous publications related to emerging incremental forming technologies, i.e., laser-assisted ISF, water jet ISF, electrically-assisted ISF and ultrasonic-assisted ISF, are also reviewed. The paper seeks to guide and inspire researchers by identifying the current development trends of the valuable contributions made in the field of SPIF of lightweight metallic materials.

Forces in Single Point and Two Point Incremental Forming

2005 ◽  
Vol 6-8 ◽  
pp. 449-456 ◽  
Author(s):  
J. Jeswiet ◽  
Joost R. Duflou ◽  
Alexander Szekeres
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming

Forces have been measured in Two Point Incremental Forming and Single Point Incremental Forming of Sheet Metal. It is necessary to know the magnitude of these forces when trying to determine if the equipment available is capable of Forming Sheet Metal by either one of the two foregoing processes. The magnitude of forces is also needed when developing appropriate models for the Incremental Sheet Forming. The forces measured in forming cones and truncated pyramids from AA 3003-0 are described.

Experimental Investigations and Numerical Analysis for Improving Knowledge of Incremental Sheet Forming Process for Sheet Metal Parts

2009 ◽  
Vol 623 ◽  
pp. 37-48 ◽  
Author(s):  
Steeve Dejardin ◽  
Jean Claude Gelin ◽  
Sebastien Thibaud
Keyword(s):  
Sheet Metal ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Experimental Investigations ◽  
Metal Parts ◽  
Sheet Metal Parts ◽  
Forming Strategy ◽  
Set Up

The paper is related to the analysis of shape distortions and springback effects arising in Single Point Incremental Forming. An experimental set up has been designed and manufactured to carry single point incremental forming on small size sheet metal parts. The experimental set up is mounted on 3-axes CNC milling machine tool and the forming tool is attached and move with the spindle. Experiments have been carried out on sheet metal parts to obtain tronconical shapes. The forming strategy associated to the movement of the forming tool has been also investigated. The experiments indicate that shape distortions arising in the corners of the tronconical shape are clearly related to forming strategy. The springback of rings cut in the tronconical parts have been also investigated. It is shown that positive or negative springback could be also related to forming strategy. In order to enhance experimental investigations, Finite Element simulations of the incremental sheet forming have been performed. Results obtained from the simulations prove that if boundary conditions and forming strategy carefully are taking into account, the finite elements results are in good agreement with experiments. So it is then possible to use FEM as a design tool for incremental sheet forming.

scholarly journals Design and manufacturing of a fixing device for incremental sheet forming process

2018 ◽  
Vol 178 ◽  
pp. 02004 ◽  
Author(s):  
Daniel Nasulea ◽  
Gheorghe Oancea
Keyword(s):  
Sheet Metal ◽  
Deep Drawing ◽  
Incremental Forming ◽  
Single Point ◽  
Fem Simulation ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Design And Manufacturing

In incremental sheet forming processes, the expensive dedicated tool are avoided and replaced with a cheap and simple fixing device which support the sheet metal blanks. The current paper presents how a fixing device used for single point incremental forming device is designed, FEM simulated and manufactured. The fixing device can be used for parts with a cone frustum and pyramidal frustum made of DC05 deep drawing steel. The forces developed in the process and the device displacements were estimated using FEM simulation. The device components were manufactured using a CNC machines and the physical assembly is also presented in the paper.

Multiobjective optimization of process variables in single-point incremental forming using grey relational analysis coupled with entropy weights

2021 ◽  
pp. 146442072110204
Author(s):  
Abdulmajeed Dabwan ◽  
Adham E Ragab ◽  
Mohamed A Saleh ◽  
Atef M Ghaleb ◽  
Mohamed Z Ramadan ◽  
...  
Keyword(s):  
Grey Relational Analysis ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Numerical Control ◽  
Single Point Incremental Forming ◽  
Process Variables ◽  
Relational Analysis ◽  
Grey Relational

Incremental sheet forming is a specific group of sheet forming methods that enable the manufacture of complex parts utilizing computer numerical control instead of specialized tools. It is an incredibly adaptable operation that involves minimal usage of sophisticated tools, dies, and forming presses. Besides its main application in the field of rapid prototyping, incremental sheet forming processes can be used for the manufacture of unique parts in small batches. The goal of this study is to broaden the knowledge of the deformation process in single-point incremental forming. This work studies the deformation behavior in single-point incremental forming by experimentally investigating the principal stresses, principal strains, and thinning of single-point incremental forming products. Conical-shaped components are fabricated using AA1050-H14 aluminum alloy at various combinations of fundamental variables. The factorial design is employed to plan the experimental study and analysis of variance is conducted to analyze the results. The grey relational analysis approach coupled with entropy weights is also implemented to identify optimum process variables for single-point incremental forming. The results show that the tool diameter has the greatest effect on the thinning of the SPIF product, followed by the sheet thickness, step size, and feed rate.

Parameter optimization and texture evolution in single point incremental sheet forming process

2019 ◽  
Vol 234 (1-2) ◽  
pp. 126-139 ◽  
Author(s):  
Shamik Basak ◽  
K Sajun Prasad ◽  
Amarjeet Mehto ◽  
Joy Bagchi ◽  
Y Shiva Ganesh ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Regression Models ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Single Point Incremental Forming ◽  
Input Process ◽  
Truncated Cone

Prototyping through incremental sheet forming is emerging as a latest trend in the manufacturing industries for fabricating personalized components according to customer requirement. In this study, a laboratory scale single-point incremental forming test setup was designed and fabricated to deform AA6061 sheet metal plastically. In addition, response surface methodology with Box–Behnken design technique was used to establish different regression models correlating input process parameters with mechanical responses such as angle of failure, part depth per unit time and surface roughness. Correspondingly, the regression models were implemented to optimize the input process parameters, and the predicted responses were successfully validated at the optimal conditions. It was observed that the predicted absolute error for angle of failure, part depth per unit time and surface roughness responses was approximately 0.9%, 4.4% and 6.3%, respectively, for the optimum parametric combination. Furthermore, the post-deformation responses from an optimized single point incremental forming truncated cone were correlated with microstructural evolution. It was observed that the peak hardness and highest areal surface roughness of 158 ± 9 HV and 1.943 μm, respectively, were found near to the pole of single-point incremental forming truncated cone, and the highest major plastic strain at this region was 0.80. During incremental forming, a significant increase in microhardness occurred due to grain refinement, whereas a substantial increase in the Brass and S texture component was responsible for the increase in the surface roughness.

scholarly journals Cranial Reconstruction Using Double Side Incremental Forming

2015 ◽  
Vol 639 ◽  
pp. 535-542 ◽  
Author(s):  
Bin Lu ◽  
Dong Kai Xu ◽  
Run Zhe Liu ◽  
Heng An Ou ◽  
Hui Long ◽  
...  
Keyword(s):  
Tool Path ◽  
Incremental Forming ◽  
Thickness Distribution ◽  
Single Point ◽  
Pure Titanium ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Geometric Accuracy ◽  
Backing Plate ◽  
Cranial Implant

Incremental sheet forming (ISF) is a highly versatile and flexible process for rapid manufacturing of complex sheet metal parts. Comparing to conventional sheet forming processes, ISF is of a clear advantage in manufacturing small batch or customized products such as cranial implant. Although effort on cranial reconstruction by using incremental sheet forming approach has been made in recent years, research has been mostly based on the single point incremental forming (SPIF) strategy and there are still considerable technical challenges for achieving better geometric accuracy, thickness distribution and complex cranial shape. In addition, the use of a backing plate or supporting die reduces the process flexibility and increases the cost. To overcome these limitations, double side incremental sheet forming (DSIF) process is employed for forming Grade 1 pure titanium sheet by using different toolpath strategies. The geometric accuracy and thickness distribution of the final part are evaluated so the optimized tool path strategies are developed. This leads to an assessment of the DSIF based approach for the application in cranial reconstruction.

Brass 70/30 and Incremental Sheet Forming Process

2013 ◽  
Vol 554-557 ◽  
pp. 1419-1431 ◽  
Author(s):  
Daniel Fritzen ◽  
Anderson Daleffe ◽  
Jovani Castelan ◽  
Lirio Schaeffer
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Cnc Machining ◽  
Forming Process ◽  
Wall Angle ◽  
Machining Center ◽  
Cad Cam ◽  
Cnc Machining Center

This work addresses through bibliographies and experiments the behavior of sheet brass 70/30 for Incremental Sheet Forming process - ISF, based on the parameters: wall angle (), step vertical (ΔZ) strategy and the way the tool. Experiments based on the method called Single Point Incremental Forming - SPIF. For execution of practical tests, we used the resources: software CAD / CAM, CNC machining center with three axles, matrix incremental, incremental forming tool and a device press sheets. Furthermore, measurement was made of the true deformation () and thickness (s1). Practical tests have shown that the spiral machining strategy yielded a greater wall angle, compared to the conventional strategy outline.

Incremental Forming of Sandwich Panels

2007 ◽  
Vol 344 ◽  
pp. 591-598 ◽  
Author(s):  
K.P. Jackson ◽  
J.M. Allwood ◽  
M. Landert
Keyword(s):  
Mild Steel ◽  
Sheet Metal ◽  
Sandwich Panel ◽  
Incremental Forming ◽  
Sandwich Panels ◽  
Economic Benefits ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Sheet Metals

This paper presents a first investigation of the applicability of incremental sheet forming (ISF) to sandwich panels. Two initial tests on various sandwich panel designs established that sandwich panels which are ductile and incompressible are the most suitable for the process. Further tests on a sandwich panel with mild steel face plates and a continuous polypropylene core demonstrated that patterns of deformation and tool forces followed similar trends to a sheet metal. It is concluded that, where mechanically feasible, ISF can be applied to sandwich panels using existing knowledge of sheet metals with the expectation of achieving similar economic benefits. Potentially this will increase the range of applications for which sandwich panels are viable.

Customized cranial implant manufactured by incremental sheet forming using a biocompatible polymer

2018 ◽  
Vol 24 (1) ◽  
pp. 120-129 ◽  
Author(s):  
Isabel Bagudanch ◽  
María Luisa García-Romeu ◽  
Ines Ferrer ◽  
Joaquim Ciurana
Keyword(s):  
Incremental Forming ◽  
Raw Materials ◽  
Single Point ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Scanning System ◽  
Geometric Accuracy ◽  
Biocompatible Polymer ◽  
Content Type ◽  
Cranial Implant

Purpose The purpose of this paper is to demonstrate the feasibility of incremental sheet forming (ISF), using the most common variants, single-point incremental forming (SPIF) and two-point incremental forming (TPIF), to produce prototypes of customized cranial implants using a biocompatible polymer (ultrahigh molecular weight polyethylene, UHMWPE), ensuring an appropriate geometric accuracy and cost. Design/methodology/approach The cranial implant is designed based on computerized tomographies (CT) of the patient, converting them into a 3D model using the software InVesalius. To generate the toolpath for the forming operation computer-aided manufacturing (CAM) software is used. Once the cranial implant is manufactured, a 3D scanning system is used to determine the geometric deviation between the real part and the initial design. Findings The results corroborate that it is possible to successfully manufacture a customized cranial implant using ISF, being able to improve the geometric accuracy using the TPIF variant with a negative die. Originality/value This paper is one of the first research works in which a customized cranial implant is successfully manufactured using a flexible technology, ISF and a biocompatible polymer. The use of polymeric implants in cranioplasty is advantageous because of their lightweight, low heat conductivity and mechanical properties similar to bone. Furthermore, the cost of the implant has been calculated considering not only the raw materials and manufacturing time but also the environmental impact, revealing that it is a cheap process with a low lead-time.

Asymmetric Incremental Sheet Forming

2005 ◽  
Vol 6-8 ◽  
pp. 35-58 ◽  
Author(s):  
J. Jeswiet
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Incremental Forming ◽  
Sheet Forming ◽  
Incremental Sheet Forming ◽  
Localized Deformation ◽  
Recent Advances ◽  
Conventional Spinning ◽  
Forming Methods

The use of computers in manufacturing has enabled the development of several new sheet metal forming processes. This paper describes modifications that have been made to traditional forming methods such as conventional spinning and shear forming, where deformation is localized. Recent advances have enabled this localized deformation to be accurately controlled and studied. Current developments have been focused on forming asymmetric parts using CNC technology, without the need for costly dies. Asymmetric Incremental Forming has the potential to revolutionize sheet metal forming, making it accessible to all levels of manufacturing.

Sign in / Sign up

Export Citation Format

Share Document