scholarly journals On the Effectiveness of Different Surface Finishing Techniques on A357.0 Parts Produced by Laser-Based Powder Bed Fusion: Surface Roughness and Fatigue Strength

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1284 ◽  
Author(s):  
Lucia Denti ◽  
Antonella Sola
Keyword(s):  
Surface Roughness ◽  
Fatigue Strength ◽  
Surface Finish ◽  
Shot Peening ◽  
Fatigue Behavior ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Present Contribution ◽  
Laser Shock Processing ◽  
Powder Bed

Laser-based powder bed fusion (L-PBF) is an additive manufacturing (AM) technique that uses a computer-controlled laser beam as the energy source to consolidate a metal powder according to a layer-upon-layer strategy in order to manufacture a three dimensional part. This opens the way for an unprecedented freedom in geometry, but the layer-wise build-up strategy typically results in a very poor surface finish, which is affected by the staircase effect and by the presence of partially molten particles. Surface finishing treatments are therefore necessary to obtain an adequate surface finish, to improve the fatigue behavior and to meet mechanical and aesthetic needs. The present contribution systematically compares numerous surface finishing techniques, including laser shock processing, plastic media blasting, sand blasting, ceramic shot peening and metal shot peening with steel particles of different sizes (ϕ = 0.2 mm and ϕ = 0.4 mm). The results show that all the proposed methods improve the surface quality and the fatigue life of A357.0 L-PBF parts. However, the achievement of the lowest surface roughness does not necessarily correspond to the best fatigue performance, thus suggesting that multiple mechanisms may be active and that besides surface roughness also residual stresses contribute to increase the fatigue strength.

scholarly journals Effect of Surface and Subsurface Defects on Fatigue Behavior of AlSi10Mg Alloy Processed by Laser Powder Bed Fusion (L-PBF)

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1063 ◽  
Author(s):  
Milad Hamidi Nasab ◽  
Alessandro Giussani ◽  
Dario Gastaldi ◽  
Valeria Tirelli ◽  
Maurizio Vedani
Keyword(s):  
Crack Nucleation ◽  
Fatigue Behavior ◽  
Fatigue Behaviour ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Processes ◽  
Effect Of Surface ◽  
Subsurface Defects

The fatigue behaviour of an AlSi10Mg alloy processed by laser powder bed fusion (L-PBF) and subjected to different surface finishing processes was investigated paying special attention to the residual defects on the surface and the dominant fatigue failure mechanisms. Roughness measurements and qualitative surface morphology analysis showed smooth surfaces in the case of vibro-finishing and machining followed by polishing. The fatigue performance did not reveal to be directly related to surface roughness, but residual intrusions left on the finished surfaces. Post-mortem analysis showed single- or multiple-crack nucleation from pores opened on the surface, un-melted powders, or spatters considered as typical L-PBF defects. A fatigue limit of 195 MPa for machined and polished samples was obtained by substantial removal of surface and subsurface defects.

Unsettled Topics on Surface Finishing of Metallic Powder Bed Fusion Parts in the Mobility Industry

2021 ◽  
Author(s):  
Kevin Slattery ◽  
Keyword(s):  
Surface Roughness ◽  
Electron Beam ◽  
High Surface ◽  
Metallic Powder ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Challenges And Opportunities ◽  
The Cost ◽  
Fatigue Corrosion

Laser and electron-beam powder bed fusion (PBF) additive manufacturing (AM) technology has transitioned from prototypes and tooling to production components in demanding fields such as medicine and aerospace. Some of these components have geometries that can only be made using AM. Initial applications either take advantage of the relatively high surface roughness of metal PBF parts, or they are in fatigue, corrosion, or flow environments where surface roughness does not impose performance penalties. To move to the next levels of performance, the surfaces of laser and electron-beam PBF components will need to be smoother than the current as-printed surfaces. This will also have to be achieve on increasingly more complex geometries without significantly increasing the cost of the final component. Unsettled Topics on Surface Finishing of Metallic Powder Bed Fusion Parts in the Mobility Industry addresses the challenges and opportunities of this technology, and what remains to be agreed upon by the industry.

scholarly journals Fatigue Behavior of Hybrid Components Containing Maraging Steel Parts Produced by Laser Powder Bed Fusion

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 835
Author(s):  
Luís Santos ◽  
Joel de de Jesus ◽  
Luís Borrego ◽  
José A. M. Ferreira ◽  
Rui F. Fernandes ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Fatigue Failure ◽  
Fatigue Behavior ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Hybrid Parts ◽  
Aisi H13 ◽  
Steel Aisi ◽  
Loading Tests

This investigation concerns about of fatigue behavior under controlled loading and under strain control for hybrid specimens with parts produced with conventional processes in steel AISI H13 and the stainless steel AISI 420 and the rest part produced by laser powder bed fusion in AISI 18Ni300 steel. The controlled loading tests were performed in constant and variable amplitude. Fatigue failure of hybrid samples occurs mostly in laser-melted parts, initiated around the surface, in many cases with multi-nucleation and propagated predominantly between the deposited layers. Fatigue strength of hybrid parts, tested under displacement control is similar, but for specimens tested under load control the fatigue strength the fatigue strength of hybrid specimens is progressively lesser than laser powder bed fusion samples. Despite a tendency to obtain conservative predictions, Miner’s law predicts reasonably the fatigue lives under block loadings. The interface between materials presented an excellent joining and fatigue strength because the fatigue failure of hybrid samples occurred mostly in laser melted parts out of the interface.

scholarly journals On the Relevance of Volumetric Energy Density in the Investigation of Inconel 718 Laser Powder Bed Fusion

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 538 ◽  
Author(s):  
Fabrizia Caiazzo ◽  
Vittorio Alfieri ◽  
Giuseppe Casalino
Keyword(s):  
Surface Roughness ◽  
Energy Density ◽  
Process Parameters ◽  
Vickers Hardness ◽  
Powder Bed Fusion ◽  
Processing Conditions ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Fractional Density ◽  
Experimental Variation

Laser powder bed fusion (LPBF) can fabricate products with tailored mechanical and surface properties. In fact, surface texture, roughness, pore size, the resulting fractional density, and microhardness highly depend on the processing conditions, which are very difficult to deal with. Therefore, this paper aims at investigating the relevance of the volumetric energy density (VED) that is a concise index of some governing factors with a potential operational use. This paper proves the fact that the observed experimental variation in the surface roughness, number and size of pores, the fractional density, and Vickers hardness can be explained in terms of VED that can help the investigator in dealing with several process parameters at once.

scholarly journals The Effect of Cu Content and Surface Finish on the Metal Dusting Resistance of Additively Manufactured NiCu Alloys

2021 ◽  
Author(s):  
Katrin Jahns ◽  
Anke S. Ulrich ◽  
Clara Schlereth ◽  
Lukas Reiff ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Surface Finish ◽  
Powder Bed Fusion ◽  
Metal Dusting ◽  
Laser Powder Bed Fusion ◽  
Roughness Measurement ◽  
Powder Bed ◽  
Cu Content ◽  
Binary Model ◽  
Interesting Candidate ◽  
Nicu Alloys

AbstractDue to the inhibiting behavior of Cu, NiCu alloys represent an interesting candidate in carburizing atmospheres. However, manufacturing by conventional casting is limited. It is important to know whether the corrosion behavior of conventionally and additively manufactured parts differ. Samples of binary NiCu alloys and Monel Alloy 400 were generated by laser powder bed fusion (LPBF) and exposed to a carburizing atmosphere (20 vol% CO–20% H2–1% H2O–8% CO2–51% Ar) at 620 °C and 18 bar for 960 h. Powders and printed samples were investigated using several analytic techniques such as EPMA, SEM, and roughness measurement. Grinding of the material after building (P1200 grit surface finish) generally reduced the metal dusting attack. Comparing the different compositions, a much lower attack was found in the case of the binary model alloys, whereas the technical Monel Alloy 400 showed a four orders of magnitude higher mass loss during exposure despite its Cu content of more than 30 wt%.

scholarly journals Gold, Silver, and Electrum Electroless Plating on Additively Manufactured Laser Powder-Bed Fusion AlSi10Mg Parts: A Review

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Dana Ashkenazi ◽  
Alexandra Inberg ◽  
Yosi Shacham-Diamand ◽  
Adin Stern
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Ion Beam ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Process ◽  
Gold Silver ◽  
3D Printed

Additive manufacturing (AM) revolutionary technologies open new opportunities and challenges. They allow low-cost manufacturing of parts with complex geometries and short time-to-market of products that can be exclusively customized. Additive manufactured parts often need post-printing surface modification. This study aims to review novel environmental-friendly surface finishing process of 3D-printed AlSi10Mg parts by electroless deposition of gold, silver, and gold–silver alloy (e.g., electrum) and to propose a full process methodology suitable for effective metallization. This deposition technique is simple and low cost method, allowing the metallization of both conductive and insulating materials. The AlSi10Mg parts were produced by the additive manufacturing laser powder bed fusion (AM-LPBF) process. Gold, silver, and their alloys were chosen as coatings due to their esthetic appearance, good corrosion resistance, and excellent electrical and thermal conductivity. The metals were deposited on 3D-printed disk-shaped specimens at 80 and 90 °C using a dedicated surface activation method where special functionalization of the printed AlSi10Mg was performed to assure a uniform catalytic surface yielding a good adhesion of the deposited metal to the substrate. Various methods were used to examine the coating quality, including light microscopy, optical profilometry, XRD, X-ray fluorescence, SEM–energy-dispersive spectroscopy (EDS), focused ion beam (FIB)-SEM, and XPS analyses. The results indicate that the developed coatings yield satisfactory quality, and the suggested surface finishing process can be used for many AM products and applications.

Multi-Objective Build Orientation Optimization for Powder Bed Fusion by Laser

2017 ◽  
Vol 139 (11) ◽  
Author(s):  
Salah Eddine Brika ◽  
Yaoyao Fiona Zhao ◽  
Mathieu Brochu ◽  
Justin Mezzetta
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Integrated Approach ◽  
Powder Bed Fusion ◽  
Powder Bed ◽  
Build Orientation ◽  
Multi Objective ◽  
Build Time ◽  
Process Factors ◽  
Experimental Data Analysis

This paper proposes an integrated approach to determine optimal build orientation for powder bed fusion by laser (PBF-L), by simultaneously optimizing mechanical properties, surface roughness, the amount of support structure (SUPP), and build time and cost. Experimental data analysis has been used to establish the objective functions for different mechanical properties and surface roughness. Geometry analysis of the part has been used to estimate the needed SUPP and thus evaluate the build time and cost. Normalized weights are assigned to different objectives depending on their relative importance allowing solving the multi-objective optimization problem using a genetic optimization algorithm. A study case is presented to demonstrate the capabilities of the developed system. The major achievements of this work are the consideration of multiple objectives and the establishment of objective function considering different load direction and heat treatments. A user-friendly graphical user interface was developed allowing to control different optimization process factors and providing different visualization and evaluation tools.

Sign in / Sign up

Export Citation Format

Share Document