scholarly journals Effect of Graphene Oxide on Mechanical Properties and Durability of Ultra-High-Performance Concrete Prepared from Recycled Sand

Nanomaterials ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 1718 ◽  
Author(s):  
Hongyan Chu ◽  
Yu Zhang ◽  
Fengjuan Wang ◽  
Taotao Feng ◽  
Liguo Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
High Performance ◽  
High Performance Concrete ◽  
Construction Material ◽  
Chloride Ions ◽  
Raw Material ◽  
Ultra High Performance Concrete ◽  
River Sand ◽  
The Impact

Ultra-high-performance concrete (UHPC) has been used as an advanced construction material in civil engineering because of its excellent mechanical properties and durability. However, with the depletion of the raw material (river sand) used for preparing UHPC, it is imperative to find a replacement material. Recycled sand is an alternative raw material for preparing UHPC, but it degrades the performance. In this study, we investigated the use of graphene oxide (GO) as an additive for enhancing the properties of UHPC prepared from recycled sand. The primary objective was to investigate the effects of GO on the mechanical properties and durability of the UHPC at different concentrations. Additionally, the impact of the GO additive on the microstructure of the UHPC prepared from recycled sand was analysed at different mixing concentrations. The addition of GO resulted in the following: (1) The porosity of the UHPC prepared from recycled sand was reduced by 4.45–11.35%; (2) the compressive strength, flexural strength, splitting tensile strength, and elastic modulus of the UHPC prepared from recycled sand were enhanced by 8.24–16.83%, 11.26–26.62%, 15.63–29.54%, and 5.84–12.25%, respectively; (3) the resistance of the UHPC to penetration of chloride ions increased, and the freeze–thaw resistance improved; (4) the optimum mixing concentration of GO in the UHPC was determined to be 0.05 wt.%, according to a comprehensive analysis of its effects on the microstructure, mechanical properties, and durability of the UHPC. The findings of this study provide important guidance for the utilisation of recycled sand resources.

scholarly journals The Mechanical Properties and Damage Evolution of UHPC Reinforced with Glass Fibers and High-Performance Polypropylene Fibers

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2455
Author(s):  
Jiayuan He ◽  
Weizhen Chen ◽  
Boshan Zhang ◽  
Jiangjiang Yu ◽  
Hang Liu
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Damage Evolution ◽  
High Performance ◽  
High Performance Concrete ◽  
Glass Fibers ◽  
Ultra High Performance Concrete ◽  
Concrete Damaged Plasticity ◽  
The Difference ◽  
Experimental Values

Due to the sharp and corrosion-prone features of steel fibers, there is a demand for ultra-high-performance concrete (UHPC) reinforced with nonmetallic fibers. In this paper, glass fiber (GF) and the high-performance polypropylene (HPP) fiber were selected to prepare UHPC, and the effects of different fibers on the compressive, tensile and bending properties of UHPC were investigated, experimentally and numerically. Then, the damage evolution of UHPC was further studied numerically, adopting the concrete damaged plasticity (CDP) model. The difference between the simulation values and experimental values was within 5.0%, verifying the reliability of the numerical model. The results indicate that 2.0% fiber content in UHPC provides better mechanical properties. In addition, the glass fiber was more significant in strengthening the effect. Compared with HPP-UHPC, the compressive, tensile and flexural strength of GF-UHPC increased by about 20%, 30% and 40%, respectively. However, the flexural toughness indexes I5, I10 and I20 of HPP-UHPC were about 1.2, 2.0 and 3.8 times those of GF-UHPC, respectively, showing that the toughening effect of the HPP fiber is better.

Volumetric Changes of the UHPC Matrix and its Determination

2016 ◽  
Vol 827 ◽  
pp. 215-218 ◽  
Author(s):  
David Čítek ◽  
Milan Rydval ◽  
Jiří Kolísko
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Experimental Tests ◽  
Structure Design ◽  
Ultra High Performance Concrete ◽  
Fine Grained ◽  
Durability Properties ◽  
Shrinkage And Creep

Research in the Ultra-High Performance Concrete applications field is very important. Current experiences shows that the structure design should be optimize due to relatively new fine-grained cement-based Hi-Tech material with excellent mechanical and durability properties. It is not sure if some of the volumetric changes like creep or shrinkage has or has not an impact on an advantage for the construction and for the structure design. The effect of the shrinkage and creep of common used concretes are well known and well described at publications but the effect of volumetric changes of the UHPC is mostly unknown because of the fact that some of experimental tests are long term and the development of UHPC is still in its basics. A lot of works are focused on a basic mechanical properties and durability tests.

Impact of Steel Fibers on Workability and Properties of UHPC

2016 ◽  
Vol 249 ◽  
pp. 57-61 ◽  
Author(s):  
Milan Rydval ◽  
Tomáš Bittner ◽  
Jiří Kolísko ◽  
Šárka Nenadálová
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Fresh Concrete ◽  
Mixture Design ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Hardened Cement ◽  
The Impact

This paper is focused on properties of fresh and hardened cement-based composite Ultra-High Performance Concrete with regard to different volume fraction of short brass coated steel fibers BASF MASTERFIBER® 482. Workability of fresh concrete and basic mechanical properties (tensile strength in bending, compressive strength) of hardened UHPC were found out. The workability of fresh concrete was measured by small mortar Haegermann cone. Percentage differences at cost were obtained at hardened concrete, too. The aim of the first experimental part of the research was the impact of volume fraction of steel fibers according to workability of fresh concrete and also according to mechanical properties of hardened UHPC with the same volume fraction of each component of the mixture, only the volume fraction of the steel fibers was different at each mixture. The mixture design of UHPC was changed to maintaining the workability of fresh concrete at the second part of the research. The workability at mixture with dosage of steel fibers of 300 kg/m3 measured by Haegermann cone was around 300 mm. In the framework of grant project GAČR 15-05791S the basic mechanical properties of hardened fine-grained cementitious composite material UHPC at small beams size of 160/40/40 mm and beams size 300/70/70 mm were determined. The aim of the research project was not only the determination of basic mechanical properties for each mixture design but also workability assessment and costs linked with higher amount of the volume fracture of steel fibers.

scholarly journals Effect of Graphene Oxide Nanosheets on Physical Properties of Ultra-High-Performance Concrete with High Volume Supplementary Cementitious Materials

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1929 ◽  
Author(s):  
Yu-You Wu ◽  
Jing Zhang ◽  
Changjiang Liu ◽  
Zhoulian Zheng ◽  
Paul Lambert
Keyword(s):  
Graphene Oxide ◽  
Physical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
High Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Slump Flow

Nanomaterials have been increasingly employed for improving the mechanical properties and durability of ultra-high-performance concrete (UHPC) with high volume supplementary cementitious materials (SCMs). Recently, graphene oxide (GO) nanosheets have appeared as one of the most promising nanomaterials for enhancing the properties of cementitious composites. To date, a majority of studies have concentrated on cement pastes and mortars with fewer investigations on normal concrete, ultra-high strength concrete, and ultra-high-performance cement-based composites with a high volume of cement content. The studies of UHPC with high volume SCMs have not yet been widely investigated. This paper presents an experimental investigation into the mini slump flow and physical properties of such a UHPC containing GO nanosheets at additions from 0.00 to 0.05% by weight of cement and a water–cement ratio of 0.16. The study demonstrates that the mini slump flow gradually decreases with increasing GO nanosheet content. The results also confirm that the optimal content of GO nanosheets under standard curing and under steam curing is 0.02% and 0.04%, respectively, and the corresponding compressive and flexural strengths are significantly improved, establishing a fundamental step toward developing a cost-effective and environmentally friendly UHPC for more sustainable infrastructure.

Factorial Design Approach of Ultra-High Performance Concrete

2013 ◽  
Vol 405-408 ◽  
pp. 2847-2850
Author(s):  
Wu Jian Long ◽  
Wei Lun Wang ◽  
Qi Ling Luo ◽  
Bi Qin Dong
Keyword(s):  
Mechanical Properties ◽  
Factorial Design ◽  
Statistical Models ◽  
High Performance ◽  
High Performance Concrete ◽  
High Strength ◽  
Design Approach ◽  
Ultra High Performance Concrete ◽  
Self Consolidating Concrete ◽  
Slump Flow

In order to understand the influence of mixture parameters on ultra-high strength self-consolidating concrete (UHS-SCC) behaviour, an experimental design was carried out in this investigation. In total, 19 SCC mixtures were prepared to determine several key responses that affect the slump flow and compressive strength of UHS-SCC. The statistical models derived from the factorial design approach can be used to quantify the effect of mixture parameters and their coupled effects on fresh and mechanical properties of SCC.

Sign in / Sign up

Export Citation Format

Share Document