scholarly journals Modification of Microelectrode Arrays with High Surface Area Dendritic Platinum 3D Structures: Enhanced Sensitivity for Oxygen Detection in Ionic Liquids

Nanomaterials ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 735 ◽  
Author(s):  
Ghulam Hussain ◽  
Anthony O’Mullane ◽  
Debbie Silvester
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
3D Structures ◽  
Surface Areas ◽  
Enhanced Sensitivity ◽  
Redox Active ◽  
Low Concentrations ◽  
One Step

Electrochemical gas sensors are often used for identifying and quantifying redox-active analyte gases in the atmosphere. However, for amperometric sensors, the current signal is usually dependent on the electroactive surface area, which can become small when using microelectrodes and miniaturized devices. Microarray thin-film electrodes (MATFEs) are commercially available, low-cost devices that give enhanced current densities compared to mm-sized electrodes, but still give low current responses (e.g., less than one nanoamp), when detecting low concentrations of gases. To overcome this, we have modified the surface of the MATFEs by depositing platinum into the recessed holes to create arrays of 3D structures with high surface areas. Dendritic structures have been formed using an additive, lead acetate (Pb(OAc)2) into the plating solution. One-step and two-step depositions were explored, with a total deposition time of 300 s or 420 s. The modified MATFEs were then studied for their behavior towards oxygen reduction in the room temperature ionic liquid (RTIL) [N8,2,2,2][NTf2]. Significantly enhanced currents for oxygen were observed, ranging from 9 to 16 times the current of the unmodified MATFE. The highest sensitivity was obtained using a two-step deposition with a total time of 420 s, and both steps containing Pb(OAc)2. This work shows that commercially-available microelectrodes can be favorably modified to give significantly enhanced analytical performances.

Carbon Dioxide Adsorption Using High Surface Area Activated Carbons from Local Coals Modified by KOH, NaOH and ZnCl2 Agents

2017 ◽  
Vol 15 (3) ◽  
Author(s):  
Atakan Toprak ◽  
Turkan Kopac
Keyword(s):  
Surface Area ◽  
Activated Carbons ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Micropore Volume ◽  
Bet Surface Area ◽  
Dft Methods ◽  
Surface Areas ◽  
Adsorption Capacities

Abstract Activated carbons of various features were produced by the impregnation of local coal samples that were taken from Kilimli region of Zonguldak (Turkey) with chemical agents KOH, NaOH and ZnCl2 at different temperatures (600–800 °C) and concentrations (1:1–6:1 agent:coal), for their evaluation in CO2 adsorption studies. BET, DR, t-plot and DFT methods were used for the characterization of carbon samples based on N2 adsorption data obtained at 77 K. The pore sizes of activated carbons produced were generally observed to be in between 13–25 Å, containing highly micropores. Mesopore formations were higher in samples treated with ZnCl2. The highest value for the BET surface area was found as 2,599 m2 g−1 for the samples treated with KOH at 800 °C with a KOH to coal ratio of 4:1. It was observed that the CO2 adsorption capacities obtained at atmospheric pressure and 273 K were considerably affected by the micropore volume and surface area. The highest CO2 adsorption capacities were found as 9.09 mmol/g (28.57 % wt) and 8.25 mmol g−1 (26.65 % wt) for the samples obtained with KOH and NaOH treatments, respectively, at ratio of 4:1. The activated carbons produced were ordered as KOH>NaOH>ZnCl2, according to their surface areas, micropore volumes and CO2 adsorption capacities. The low-cost experimental methods developed by the utilization of local coals in this study enabled an effective capture of CO2 before its emission to atmosphere.

Preparation of N-Doped Nanoporous Carbon from Crude Biomass and its Electrochemical Activity

NANO ◽  
2016 ◽  
Vol 11 (03) ◽  
pp. 1650028 ◽  
Author(s):  
Zezhong Xu ◽  
Jingyu Si
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Lithium Ion ◽  
Nanoporous Carbon ◽  
High Specific Surface Area ◽  
Electrochemical Sensing ◽  
Potential Candidate ◽  
Surface Areas

H2O2 detection plays an important role in electrochemical sensing since H2O2 often acts as an intermediate product or regulator in various reactions. Nanoporous carbon (NPC) can be a potential candidate in electrochemical sensing because of its high specific surface area, various pore sizes and structures. In this work, we reported the preparation of N-doped NPC derived from the highly available, accessible and recyclable plant Typha orientalis. The products have high surface area (highest surface areas of 1439.0 m2 g[Formula: see text] and a number of nanopores. Highest content of nitrogen atom in the product is 3.66 at.%). Typical product exhibits high electrocatalytic activity for reduction of hydrogen peroxide. The product may have further use for glucose biosensing. We developed a low-cost, simple and readily scalable approach to prepare the excellent carbon electrocatalyst directly from crude biomass. In addition, because of high surface area and doping of nitrogen element, the product may find broad applications in the fields of supercapacitors, lithium-ion batteries, gas uptake and so on.

scholarly journals Lignin Based Activated Carbon Using H3PO4 Activation

Polymers ◽  
2020 ◽  
Vol 12 (12) ◽  
pp. 2829
Author(s):  
Zhongzhi Yang ◽  
Roland Gleisner ◽  
Doreen H. Mann ◽  
Junming Xu ◽  
Jianchun Jiang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Nitrogen Adsorption ◽  
Bet Surface Area ◽  
Surface Areas ◽  
Adsorption Desorption

Activated carbon (AC) with a very high surface area of over 2000 m2/g was produced from low sulfur acid hydrotropic lignin (AHL) from poplar wood using H3PO4 at a moderate temperature of 450 °C (AHL-AC6). ACs with similar surface areas were also obtained under the same activation condition from commercial hardwood alkali lignin and lignosulfonate. Initial evaluation of AC performance was carried out using nitrogen adsorption-desorption and dye adsorption. AHL-AC6 exhibited the best specific surface area and dye adsorption performance. Furthermore, the adsorption results of congo red (CR) and methylene blue (MB) showed AHL-AC6 had greater adsorption capacity than those reported in literature. The dye adsorption data fit to the Langmuir model well. The fitting parameter suggests the adsorption is nearly strong and near irreversible, especially for MB. The present study for the first time provided a procedure for producing AC from lignin with Brunauer–Emmett–Teller (BET) surface area >2000 m2/g using low cost and low environmental impact H3PO4 at moderate temperatures.

Morphology dependent adsorption of methylene blue on trititanate nanoplates and nanotubes prepared by the hydrothermal treatment of TiO2

2016 ◽  
Vol 75 (2) ◽  
pp. 350-357
Author(s):  
Graham Dawson ◽  
Wei Chen ◽  
Luhua Lu ◽  
Kai Dai
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Pore Volume ◽  
Hydrothermal Reaction ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
High Capacity ◽  
Adsorption Properties

The adsorption properties of two nanomorphologies of trititanate, nanotubes (TiNT) and plates (TiNP), prepared by the hydrothermal reaction of concentrated NaOH with different phases of TiO2, were examined. It was found that the capacity for both morphologies towards methylene blue (MB), an ideal pollutant, was extremely high, with the TiNP having a capacity of 130 mg/g, higher than the TiNT, whose capacity was 120 mg/g at 10 mg/L MB concentration. At capacity, the well-dispersed powders deposit on the floor of the reaction vessel. The two morphologies had very different structural and adsorption properties. TiNT with high surface area and pore volume exhibited exothermic monolayer adsorption of MB. TiNP with low surface area and pore volume yielded a higher adsorption capacity through endothermic multilayer adsorption governed by pore diffusion. TiNP exhibited a higher negative surface charge of −23 mV, compared to −12 mV for TiNT. The adsorption process appears to be an electrostatic interaction, with the cationic dye attracted more strongly to the nanoplates, resulting in a higher adsorption capacity and different adsorption modes. We believe this simple, low cost production of high capacity nanostructured adsorbent material has potential uses in wastewater treatment.

Highly active mixed-valent MnOxspheres constructed by nanocrystals as efficient catalysts for long-cycle Li–O2batteries

2016 ◽  
Vol 4 (43) ◽  
pp. 17129-17137 ◽  
Author(s):  
Sanpei Zhang ◽  
Zhaoyin Wen ◽  
Yang Lu ◽  
Xiangwei Wu ◽  
Jianhua Yang
Keyword(s):  
Surface Area ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Long Cycle ◽  
Highly Active

We demonstrate a low-cost and facile strategy to synthesize mixed-valent MnOxspheres constructed from nanocrystals (~5 nm), containing MnII, MnIII, and MnIVspecies. Such highly active mixed-valent MnOxspheres with high surface area greatly improve the performance of Li–O2batteries.

scholarly journals High-surface-area α-Fe2O3/carbon nanocomposite: one-step synthesis and its highly reversible and enhanced high-rate lithium storage properties

2010 ◽  
Vol 20 (11) ◽  
pp. 2092 ◽  
Author(s):  
Shu-Lei Chou ◽  
Jia-Zhao Wang ◽  
David Wexler ◽  
Konstantin Konstantinov ◽  
Chao Zhong ◽  
...  
Keyword(s):  
Surface Area ◽  
High Surface ◽  
High Surface Area ◽  
High Rate ◽  
Lithium Storage ◽  
One Step ◽  
Storage Properties ◽  
Carbon Nanocomposite
Sign in / Sign up

Export Citation Format

Share Document