scholarly journals Bioadhesive Curcumin-Mediated Photodynamic Inactivation and Its Potential to Cause Undesirable Effects on Dental and Restorative Surfaces

Pharmaceutics ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1458
Author(s):  
Bárbara Donadon Reina ◽  
Carolina Santezi Neto ◽  
Patrícia Petromilli Nordi Sasso Garcia ◽  
Marlus Chorilli ◽  
Giovana Maria Fioramonti Calixto ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Liquid Crystal ◽  
Tooth Enamel ◽  
Dental Enamel ◽  
Color Stability ◽  
Composite Resins ◽  
Photodynamic Inactivation ◽  
Restorative Material ◽  
Negative Effects ◽  
Restorative Materials

Curcumin-mediated Photodynamic Inactivation (PDI) has shown great potential to disinfect specific sites on tooth enamel but may involve contact with restorative materials. Thus, before use in dentistry, it is necessary to investigate whether the PDI protocol causes undesirable changes in the surfaces of aesthetic restorative materials and dental enamel. This study investigated the effect of PDI mediated by curcumin (CUR) in a liquid crystal precursor system on color stability (ΔE), surface roughness (Ra), and microhardness (kgf) of three different composite resins and bovine dental enamel specimens. The microhardness and roughness readings were performed 60 days after the treatments while the color readings were performed immediately, 24, 48, and 72 h, 7, 14, 21, 30, and 60 days after the treatments. Results showed that CUR mediated-PDI does not seem to have the potential to promote any esthetic or mechanical changes to the surface of tooth enamel and can be applied safely in clinical practice. However, the results on color, roughness, and hardness obtained for composite resins show that some negative effects can be produced, depending on the type of restorative material; more experiments must be performed with different formulations and, perhaps, with lower concentrations of CUR.

scholarly journals THE COMPARISON OF RESIN-BASED COMPOSITES PHYSICAL PROPERTIES BETWEEN BULK-FILL TECHNIQUE AND INCREMENTAL TECHNIQUE

2021 ◽  
Vol 6 (1) ◽  
pp. 85
Author(s):  
Rahmi Khairani Aulia
Keyword(s):  
Physical Properties ◽  
Composite Resin ◽  
Color Stability ◽  
Composite Resins ◽  
Shrinkage Stress ◽  
Restorative Material ◽  
Polymerization Shrinkage ◽  
Advantages And Disadvantages ◽  
Restoration Technique ◽  
Restoration Failure

ABSTRACT:Composite resins are currently the most popular restorative material in dentistry. This is due to good aesthetics and maximum conservation ability. Behind these advantages, there are disbenefits of composite resin materials, such as polymerization shrinkage, which can lead to restoration failure. Various attempts have been investigated to reduce the shrinkage incidence of composite resins, one of which is the technique of placing the restorative material into the cavity. The restoration filling technique is recognized as a significant factor in shrinkage stress. By using a special filling technique, the polymerization shrinkage damage stress can be reduced. There are several techniques in performing composite resin fillings, including bulk and incremental techniques. These techniques have their respective advantages and disadvantages. The aim of this literature review was to compare the physical properties of composite resin restorations with bulk filling and incremental techniques. Physical properties that being studied include polymerization shrinkage, stress shrinkage, degree of conversion, bonding strength, water resorption, color stability, and temperature increase. Comparing the two techniques, composite resin with incremental filling technique has superior physical properties compared to bulk technique. From the comparison of the two techniques, the composite resin with incremental filling technique has superior physical properties compared to the bulk technique, especially in higher conversion which causes lower shrinkage stress. This situation makes the incremental technique provide better bond strength, water resorption, color stability, and lower temperature rise.Keywords: Bulk, Composite Resin, Incremental,  Physical Properties, Restoration, Restoration Technique

scholarly journals Evaluation of the color stability and surface roughness of dual-cure, bulk-fill composites

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 266-273
Author(s):  
Zehra Şivgan Güner ◽  
Behiye Bolgül ◽  
Tacettin İnandı
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Pediatric Dentistry ◽  
Ease Of Use ◽  
Composite Resins ◽  
Distilled Water ◽  
Significant Difference ◽  
Cherry Juice ◽  
Experimental Group ◽  
Composite Samples

Aim: In recent years, tooth-colored, dual-cure, bulk-fill composite resins, which have attracted attention for their ease of use, constitute one of the latest developments in pediatric dentistry applications. This study aimed to evaluate the color stability and surface roughness properties of three different dual-cure, bulk-fill materials and one light-cure, bulk-fill composite material used in pediatric dentistry. Methodology: In this study, three different dual-cure, bulk-fill composites (Fill-Up, HyperFIL, Cention-N) and one light-polymerized bulk-fill composite (Reveal HD) were used. A total of 70 samples were obtained for surface roughness testing. The surface roughness testing was performed with a Hysitron TI 950 Triboindenter device. A total of 105 samples were obtained for the evaluation of color stability. Cherry juice, iced tea, and distilled water were used as solutions. Initial and final color measurements were made using a spectrophotometer. The color differences between measurements were recorded according to the CIEDE 2000 system. Results: The least surface roughness among the composite groups was observed in the light polymerized Cention-N composite samples in the experimental group. In the Fill-Up and Cention-N composite groups in the experimental group, the surface roughness of the samples left to self-polymerization and the samples polymerized with light showed a statistically significant difference (p < 0.05). Among the composite groups, the highest amount of coloring was observed in the Fill-Up composite samples, which were left to self-polymerization and kept in cherry juice in the experimental group. The least coloration among the composite groups was observed in the Cention-N composite samples polymerized with light and kept in distilled water. Conclusion: Based on this information, a decrease in surface roughness and an increase in color stability can be expected due to self-polymerization and the light polymerization of dual-cured, bulk-fill composites.   How to cite this article: Şivgan Güner Z, Bolgül B, İnandı T. Evaluation of the color stability and surface roughness of dual-cure, bulk-fill composites. Int Dent Res 2021;11(Suppl.1):266-273. https://doi.org/10.5577/intdentres.2021.vol11.suppl.39   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

Efficacy of polishing kits on the surface roughness and color stability of different composite resins

2017 ◽  
Vol 20 (5) ◽  
pp. 557 ◽  
Author(s):  
H Gumus ◽  
H Kocaagaoglu ◽  
T Aslan ◽  
A Gürbulak ◽  
H Albayrak ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Composite Resins

Surface roughness and color stability of various composite resins

2007 ◽  
Vol 32 (6) ◽  
pp. 542 ◽  
Author(s):  
Sung-Yi Lee ◽  
Hyeon-Cheol Kim ◽  
Bock Hur ◽  
Jeong-Kil Park
Keyword(s):  
Surface Roughness ◽  
Color Stability ◽  
Composite Resins

scholarly journals Color Stability and Surface Roughness of Hybrid and Nanofilled Composites Brushed with Abrasive Dentifrices

2021 ◽  
Vol 23 (2) ◽  
pp. 85-91
Author(s):  
Guilherme Ortiz Pinto Cruz ◽  
Larissa Martins Costa ◽  
Cesar Penazzo Lepri ◽  
Ruchele Dias Nogueira ◽  
Regina Guenka Palma-Dibb ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Laser Scanning ◽  
Color Change ◽  
Color Stability ◽  
Composite Resins ◽  
Laser Scanning Microscopy ◽  
Confocal Laser ◽  
Test Surface ◽  
Initial Color ◽  
Level Of Significance

AbstractThe aim of this study was to evaluate the color stability and the surface roughness of different composites brushed with toothpastes presenting different levels of abrasivity. Thirty discs of each material were obtained using michohybrid composites (Brilliant NG and Charisma Diamond) and a nanocomposite (Filtek Z350XT). The initial color (CIELab) and surface roughness (confocal laser scanning microscopy) of resin discs were evaluated. Afterwards, 10 specimens per group were brushed with the following dentifrices: Maximum Cavity Protection, Sensodyne Repair & Protect and Colgate Sensitive Pro-Relief. Brushing was performed with an electric toothbrush equipped with soft bristle head, with standard power and weight, for 30 minutes. Every 30 seconds, 1.0 ml of the slurry was injected between the bristles of the brush and the specimen. After abrasive challenge, the samples had their color and roughness reevaluated. Data were submitted to the Kruskal-Wallis test (color change) or the t-test (surface roughness). The level of significance was 5%. Results: Brushing did not significantly change the color of the composites tested in the study herein . On the other hand, the surface roughness of the composites was significantly affected by the abrasive challenge, regardless of the toothpaste used. The surface roughness change was similar for all the composites. The abrasive challenge with the toothpastes Maximum Cavity protection, Sensodyne Repair & Protect and Colgate Sensitive Pro-Relief was not able to significantly change the color of the composite resins. Nevertheless, the abrasive challenges significantly altered the surface roughness of all the evaluated composites. However, the changes in surface roughness were statistically similar in the microhybrid and nanofilled composites. Keywords: Composites Resins. Dentifrices. Color. ResumoO objetivo deste estudo foi avaliar a estabilidade de cor e a rugosidade superficial de diferentes resinas compostas escovadas com dentifrícios de diferentes níveis de abrasividade. Trinta discos de cada material foram obtidos utilizando compósitos micro-híbridos (Brilliant NG e Charisma Diamond) e um nanocompósito (Filtek Z350XT). A cor inicial (CIELab) e a rugosidade superficial (microscopia confocal de varredura a laser) dos discos de resina foram avaliadas. Em seguida, 10 amostras por grupo foram escovadas com os dentifrícios Máxima Proteção Anticáries, Sensodyne Repair & Protect e Colgate Sensitive Pro-Alívio. A escovação foi realizada com uma escova elétrica com cabeça de cerdas macias, com potência e peso padronizados, durante 30 minutos. A cada 30 segundos, 1,0 ml da pasta era injetada entre as cerdas da escova e a amostra. Após o desafio abrasivo, as amostras tiveram sua cor e rugosidade reavaliadas. Os dados foram submetidos ao teste de Kruskal-Wallis (alteração de cor) ou ao teste t (rugosidade da superfície) (α=5%). A escovação não alterou significativamente a cor dos compósitos. Por outro lado, a rugosidade superficial dos compósitos foi significativamente afetada pelo desafio abrasivo, independentemente do dentifrício utilizado. A alteração da rugosidade superficial foi semelhante para todos os compósitos. O desafio abrasivo com a Máxima Proteção Anticáries, o Sensodyne Repair & Protect e o Colgate Sensitive Pro-Alívio não foi capaz de alterar significativamente a cor das resinas. Diferentemente, os desafios abrasivos alteraram significativamente a rugosidade superficial de todos os compósitos avaliados. No entanto, as mudanças na rugosidade foram estatisticamente semelhantes nos compósitos micro-híbridos e nanoparticulado. Palavras-chave: Resinas Compostas. Dentifrícios. Cor.

scholarly journals Effect of Chemical Degradation on Surface Roughness and on Color Stability of Micro hybrid and Nanofilled Composites

2018 ◽  
Vol 20 (3) ◽  
pp. 167
Author(s):  
Ruchele Dias Nogueira ◽  
Rosa Maria Pereira Moisés Barbosa Andrade ◽  
Ailla Carla Rocha Acosta Lancellotti ◽  
Regina Guenka Palma-Dibb ◽  
Vinícius Rangel Geraldo-Martins
Keyword(s):  
Surface Roughness ◽  
Hybrid Composite ◽  
Orange Juice ◽  
Red Wine ◽  
Clinical Success ◽  
Artificial Saliva ◽  
Color Stability ◽  
Final Analysis ◽  
Composite Resins ◽  
Chemical Degradation

ResumoA resina composta é o material restaurador mais utilizado atualmente. Apesar de seu sucesso clínico, o material está sujeito a alterações em suas propriedades físicas, quando exposto ao meio bucal. O objetivo foi avaliar a influência da degradação química na estabilidade de cor e na rugosidade superficial de resinas micro-híbrida e nanoparticulada. Foram confeccionados 40 discos (6,0mm x 2,0mm) da resina composta micro-híbrida (Z250XT) e 40 da resina nanoparticulada (Z350XT). Após a análise da cor inicial e da rugosidade inicial, 10 discos de cada resina foram imersos em saliva artificial (Controle, pH=6,4), suco de laranja (pH= 3,4), refrigerante de limão (pH=2,9) e vinho tinto (pH=3,1), por 4 horas por dia (37ºC) durante 30 dias. Após, foram realizadas as leituras finais de cor e rugosidade. Os dados obtidos para a estabilidade de cor foram analisados pelo Teste de Kruskal-Wallis, seguido pelo Teste de Dunn (α=5%). Para a análise da rugosidade foi utilizado o Teste t para amostras pareadas (α=5%). O manchamento provocado pela saliva artificial, suco de laranja e refrigerante foi similar, mas foi estatisticamente diferente do manchamento produzido pelo vinho, em ambas as resinas testadas. O vinho produziu o mesmo grau de manchamento nas resinas micro-híbrida e nanoparticulada. Foi observado que o suco de laranja, o refrigerante e o vinho promoveram aumento da rugosidade superficial dos discos de resina. Diante disso, concluiu-se que o vinho alterou a cor de resinas compostas micro-híbrida e nanoparticulada, e que a rugosidade superficial dos discos de resina foi alterada por todas as bebidas utilizadas.Palavras chave: Resinas Compostas. Corantes. Cor.Abstract Composite resin is the most used restorative material. Despite its clinical success, it is susceptible to changes in its physical properties when exposed to the oral environment. The aim was to evaluate the influence of acidic beverages on the color stability and on the surface roughness of the nanofilled and micro hybrid composite. Forty discs (6.0mm x 2.0mm) of the micro hybrid composite (Z250XT) and 40 of the nanofilled composite (Z350XT) were manufactured. After the measurement of the initial color and the initial roughness, 10 discs of each composite were individually immersed in artificial saliva (control, pH = 6.4), orange juice (pH=3.4), lime soda (pH = 2.9) and red wine (pH = 3.1) during 4 hours per day at 37°C for 30 days. At the end of the experiment, the final analysis of color and surface roughness were performed. The data obtained for the color stability were analyzed by Kruskal-Wallis and Dunn’s test (α= 5%). For the analysis of the surface roughness, the t test for related samples was used (α= 5%). The color changes promoted by artificial saliva, orange juice and soda were similar, but they were statistically different from staining produced by wine, in both tested composites. Wine produced the same degree of staining in both composites. Orange juice, soda and red wine increased the surface roughness of the composite discs. It was concluded that red wine significantly changes the color of micro hybrid and nanofilled composites. Furthermore, all beverages increased the surface roughness of the composites tested in the study herein.Keywords: Composite Resins. Coloring Agents. Color.

scholarly journals Comparison of Surface Roughness of Two Restorative Materials after the Application of Topical Fluorides

2018 ◽  
Vol 1 (11) ◽  
pp. 339-342
Author(s):  
Saru Khosla ◽  
Vaibhav Verma ◽  
Sheena Markan
Keyword(s):  
Surface Roughness ◽  
Artificial Saliva ◽  
Tooth Surface ◽  
Restorative Material ◽  
Protective Function ◽  
Roughened Surface ◽  
Oral Environment ◽  
Restorative Materials ◽  
Topical Fluoride ◽  
Topical Fluorides

INTRODUCTION: Surface roughness and microhardness are the two important properties which provide compressive strength as well as abrasion resistance to the restorative materials. On the other side topical fluorides provide the protective function with its anti-cariogenic properties. GIC as a restorative material fulfills both of the requirements.AIM: The aim of this study is to evaluate the effect of topical fluoride application on surface roughness of various restorative materials.MATERIALS AND METHODS: This study was done on 20 extracted teeth, Conventional Glass Ionomers (Fuji II) and Resin Modified Glass Ionomers (3M ESPE Vitremer) were used as restorative materials. Topical fluoride application i.e. with 2% sodium fluoride using Knutson’s technique was done followed by storing in artificial saliva for 24 hours and then blot dried for testing of surface roughness.RESULTS: Through this study it was observed that the no statistical difference was found between both of the restorative materials. (P>0.05).CONCLUSION: In oral environment strength and life span of restorative material is one of the important criteria and roughened surface can clinically deteriorate these properties of restoration. So it’s important for a dentist to consider all the factors while applying and restoring the tooth surface.

scholarly journals Use of Resin Infiltrate for the Treatment of White spot Lesions on Dental Enamel: Case Report

2019 ◽  
Vol 21 (2) ◽  
pp. 134
Author(s):  
Rosa Maria Pereira Moisés Barbosa de Andrade ◽  
Ruchele Dias Nogueira ◽  
Maria Angélica Hueb Menezes-Oliveira ◽  
Cesar Penazzo Lepri ◽  
Vinícius Rangel Geraldo-Martins
Keyword(s):  
Tooth Enamel ◽  
Dental Enamel ◽  
Composite Resins ◽  
White Spot ◽  
White Spot Lesion ◽  
White Spot Lesions ◽  
Invasive Treatment ◽  
Resin Infiltration ◽  
Non Invasive ◽  
Infiltration Technique

Abstract Early diagnosis of white spot lesions allows non-invasive treatment to be indicated for the remineralization of active lesions. The goal was to report the clinical Protocol for the treatment of white spot lesion of a patient by the technique of resin infiltration, observing whether there is change of color on the white spot of the dental enamel after its treatment. The selected patient was 16 years old with good overall health, who featured white spot lesion of the dental enamel on tooth 13, classified as ICDAS score 2. The tooth was photographed, and its color was evaluated with the spectrophotometer in accordance with the CIELhC system. For comparison purposes, the color of tooth enamel in an area adjacent to the lesion was evaluated. The treatment of the lesion was performed with the resin infiltrate Icon (DMG, Hamburg, Germany), following the manufacturer's instructions. The color of the tooth was re-evaluated after the application of the resin infiltrate. At the end of the procedure, it was observed that the treatment of white spot lesion by resin infiltration technique reached its goal because, in addition to being minimally invasive, it was highly approved by patient and it provided the masking of the white spot lesion on the dental enamel. Keywords: Dental Caries. Dental Enamel. Composite Resins. ResumoO diagnóstico precoce de lesões de mancha branca permite que um tratamento não invasivo seja indicado para a remineralização das lesões ativas. O objetivo foi relatar o protocolo clínico para tratamento de lesão de mancha branca ativa de um paciente pela técnica do infiltrante resinoso, observando se existe alteração de cor da mancha branca do esmalte dental após o seu tratamento. Foi selecionada uma paciente, de 16 anos de idade, com boa saúde geral e que apresentava lesão de mancha branca no esmalte dental do dente 13, classificada pelo escore 2 do ICDAS. O dente foi fotografado e sua cor foi avaliada com o espectrofotômetro de acordo com o sistema CIELhC. Para fins de comparação, foi avaliada a cor do esmalte dental em uma área adjacente à lesão. O tratamento da lesão foi realizado com a resina infiltrante Icon (DMG, Hamburgo, Alemanha), seguindo as recomendações do fabricante.  A cor do dente foi reavaliada após a aplicação do infiltrante. Ao final do procedimento, observou-se que o tratamento da lesão de mancha branca pela técnica da resina infiltrante atingiu seu objetivo pois, além de ter sido minimamente invasiva, foi bem avaliada pela paciente e proporcionou o mascaramento da lesão de mancha branca do esmalte dental. Palavras-chave: Cárie Dentária. Esmalte Dentário. Resinas Compostas.

scholarly journals The Assessment of the Surface Status Following the Action of Some Acidic Beverages on Indirect Restorative Materials

2018 ◽  
Vol 55 (1) ◽  
pp. 129-135
Author(s):  
Nicoleta Tofan ◽  
Sorin Andrian ◽  
Simona Stoleriu ◽  
Irina Nica ◽  
Antonia Moldovanu ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Artificial Saliva ◽  
Study Groups ◽  
Composite Resins ◽  
Restorative Materials ◽  
Acidic Beverages ◽  
Control Samples ◽  
Red Bull

The study aimed to assess the changes of the surface roughness induced by some acidic beverages on indirect restorative materials by using profilometry. Twenty samples of three composite resins (Ceramage, SR Adoro, Luna-Wing) and three ceramics (IPS In Line, Hera Ceram, Reflex Dimension) immersed in three acidic beverages (Red Bul, wine, Coca Cola), for 5 minutes, three times daily, 14 days. The control samples were immersed in artificial saliva during the study periode. After the end of the erosive cycles and before to determine the surface roughness of the samples in the study groups, all the samples were immersed in artificial saliva for 18 hours. The surface roughness was determined in relation to the baseline surface using profilometer Perthometer_M1 (Mahr Gottingen GmbH, Germany). The immersion of the indirect restorative materials tested in the three acidic beverages lead has resulted to changes in their surface roughness. The most aggressive was wine, followed by Coca Cola, and Red Bull.

Sign in / Sign up

Export Citation Format

Share Document