scholarly journals Spiral Bevel Gears Nonlinear Vibration Having Radial and Axial Misalignments Effects

Vibration ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 666-678
Author(s):  
Moslem Molaie ◽  
Farhad S. Samani ◽  
Francesco Pellicano
Keyword(s):  
Helix Angle ◽  
Bevel Gear ◽  
Phase Portraits ◽  
Spiral Bevel Gear ◽  
Gear Pair ◽  
Mesh Stiffness ◽  
Destructive Effect ◽  
Bevel Gears ◽  
Dynamic Scenario ◽  
Spiral Bevel

In gear transmissions, vibration causes noise and malfunction. In actual applications, misalignments contribute to intensifying the destructive effect of vibrations. In this paper, the nonlinear dynamics of a spiral bevel gear pair, with small helix angle, considering different misalignments, are deeply investigated. Axial misalignment, radial misalignment, and the combination of these two types are considered in this study. The governing equation is numerically solved through an implicit Runge–Kutta scheme. Since the main goal of this study is the analysis of the dynamic scenario, the mesh stiffness of the gear pair is obtained from the literature. The dynamical system is nonlinear and time-varying; it is analyzed through time responses, phase portraits, Poincaré maps, and bifurcation diagrams. Results show that, among the considered three cases with different types of misalignments, the spiral bevel gear with axial misalignment is the worst destructive case; aperiodic, subharmonic, and multiperiod responses are observable for this case. It is interesting that the chaotic responses for the case, having both types of misalignments, are less likely for the case with axial misalignment, only.

scholarly journals EHL Analysis of Spiral Bevel Gear Pairs considering the Contact Point Migration due to Deformation under Load

2020 ◽  
Vol 2020 ◽  
pp. 1-19
Author(s):  
Xiaoyu Sun ◽  
Yanping Liu ◽  
Yongqiang Zhao ◽  
Ming Liu
Keyword(s):  
Contact Point ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Gear Pair ◽  
Spiral Bevel Gears ◽  
Actual Contact ◽  
Bevel Gears ◽  
Contact Points ◽  
Spiral Bevel

The actual contact point of a spiral bevel gear pair deviates from the theoretical contact point due to the gear deformation caused by the load. However, changes in meshing characteristics due to the migration of contact points are often ignored in previous studies on the elastohydrodynamic lubrication (EHL) analysis of spiral bevel gears. The purpose of this article is to analyze the impact of contact point migration on the results of EHL analysis. Loaded tooth contact analysis (LTCA) based on the finite element method is applied to determine the loaded contact point of the meshing tooth pair. Then, the osculating paraboloids at this point are extracted from the gear tooth surface geometry. The geometric and kinematic parameters for EHL simulation are determined according to the differential geometry theory. Numerical solutions to the Newtonian isothermal EHL of a spiral bevel gear pair at the migrated and theoretical contact points are compared to quantify the error involved in neglecting the contact point adjustment. The results show that under heavy-loaded conditions, the actual contact point of the deformed gear pair at a given pinion (gear) roll angle is different from the theoretical contact point considerably, and so do the meshing parameters. EHL analysis of spiral bevel gears under significant load using theoretical meshing parameters will result in obvious errors, especially in the prediction of film thickness.

scholarly journals Lubrication characteristics of gear after shot peening base on 25-pellet model

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401879065 ◽  
Author(s):  
Shuai Mo ◽  
Shengping Zhu ◽  
Guoguang Jin ◽  
Jiabei Gong ◽  
Zhanyong Feng ◽  
...  
Keyword(s):  
Shot Peening ◽  
High Speed ◽  
Target Material ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Spiral Bevel ◽  
Lubrication Characteristics

High-speed heavy-load spiral bevel gears put forward high requirement for flexural strength; shot peening is a technique that greatly improves the bending fatigue strength of gears. During shot peening, a large number of fine pellets bombard the surface of the metal target material at very high speeds and let the target material undergo plastic deformation, at the same time strengthening layer is produced. Spiral bevel gear as the object of being bombarded inevitably brought the tooth surface micro-morphology changes. In this article, we aim to reveal the effect of microtopography of tooth shot peening on gear lubrication in spiral bevel gear, try to establish a reasonable description of the microscopic morphology for tooth surface by shot peening, to reveal the lubrication characteristics of spiral bevel gears after shot peening treatment based on the lubrication theory, and do comparative research on the surface lubrication characteristics of a variety of microstructures.

Nonrelative sliding of spiral bevel gear mechanism based on active design of meshing line

2018 ◽  
Vol 233 (3) ◽  
pp. 1055-1067 ◽  
Author(s):  
Zhen Chen ◽  
Ming Zeng
Keyword(s):  
Design Method ◽  
Bevel Gear ◽  
Transmission Mechanism ◽  
Tooth Surface ◽  
Design Parameters ◽  
Spiral Bevel Gear ◽  
Bevel Gears ◽  
Gear Mechanism ◽  
Active Design ◽  
Spiral Bevel

In this paper, an active design method of meshing line for a spiral bevel gear mechanism with nonrelative sliding is presented. First, the general meshing line equations for a nonrelative sliding transmission mechanism between two orthogonal axes are proposed based on the active design parameters. Then, parametric equations for contact curves on the drive and driven spiral bevel gears are deduced by coordinate transformation of the meshing line equations. Further to this, parametric equations for the tooth surface of each bevel gear are derived according to the conical spiral motion of a generatrix circle along the calculated contact curves. Finally, a set of numerical examples is presented based on two types of motion equation of the meshing points. Material prototypes are fabricated and experimentally tested to validate the kinematic performance of the functionally designed spiral bevel gear set.

Kinematical Optimization of Spiral Bevel Gears

1992 ◽  
Author(s):  
Zhang-Hua Fong ◽  
Chung-Biau Tsay
Keyword(s):  
Mathematical Model ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Tooth Contact ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Contact Patterns ◽  
Spiral Bevel ◽  
Kinematic Errors

Abstract Kinematical optimization and sensitivity analysis of circular-cut spiral bevel gears are investigated in this paper. Based on the Gleason spiral bevel gear generator and EPG test machine, a mathematical model is proposed to simulate the tooth contact conditions of the spiral bevel gear set. All the machine settings and assembly data are simulated by simplified parameters. The tooth contact patterns and kinematic errors are obtained by the proposed mathematical model and the tooth contact analysis techniques. Loaded tooth contact patterns are obtained by the differential geometry and the Hertz contact formulas. Tooth surface sensitivity due to the variation of machine settings is studied. The corrective machine settings can be calculated by the sensitive matrix and the linear regression method. An optimization algorithm is also developed to minimize the kinematic errors and the discontinuity of tooth meshing. According to the proposed studies, an improved procedure for development of spiral bevel gears is suggested. The results of this paper can be applied to determine the sensitivity and precision requirements in manufacturing, and improve the running quality of the spiral bevel gears. Two examples are presented to demonstrate the applications of the optimization model.

Impact analysis and vibration reduction design of spiral bevel gears

2019 ◽  
Vol 233 (3) ◽  
pp. 668-676 ◽  
Author(s):  
Yanming Mu ◽  
Zongde Fang ◽  
Wenli Li
Keyword(s):  
Impact Velocity ◽  
Optimization Method ◽  
Bevel Gear ◽  
Spiral Bevel Gear ◽  
Load Torque ◽  
Bevel Gears ◽  
Meshing Stiffness ◽  
Polynomial Coefficients ◽  
Spiral Bevel ◽  
The Impact

To minimize the running vibration of spiral bevel gear, an optimization design method for vibration control is presented with the model of meshing impact. Firstly, based on the impact model of spiral bevel gears considering tooth deformation, the initial meshing position, meshing stiffness, and the meshing impact is studied. Secondly, the effects of load torque and rotation speed on meshing impact are analyzed. Thirdly, a mathematical model for pinion generator is built with following parameters: tool parameters, initial machine settings, and polynomial coefficients of auxiliary flank modification motion. The polynomial coefficients of the auxiliary flank modification motion are determined by optimizing the minimum impact velocity. Finally, a numerical simulation is performed. The results shows that load torque and pinion rotational speed impose significant influences on the impact. The impact velocity increases with the increase of load torque and pinion rotation speed. With load torque increasing, impact force tends to increase first and then decrease because of meshing stiffness changes, finally impact force increases dramatically due to additional load. The advantages of spiral bevel gear under the optimization of impact velocity in meshing impact are obviously. The accuracy and scientificity of the method presented in the paper for calculating the initial meshing point and meshing stiffness of complicated tooth surfaces is verified. The optimized gear obtained by the optimization method presented in the paper is also proved that owns the lowest meshing impact in the design load range. The proposed optimization method can reduce meshing impact and improve the dynamic meshing performance of spiral bevel gear. This method also can be used for optimum design of other types of gears.

Parametric Modeling for Spiral Bevel Gear Based on PRO/E

2012 ◽  
Vol 215-216 ◽  
pp. 1062-1066
Author(s):  
Xiu Hai Wu
Keyword(s):  
Parametric Design ◽  
Three Dimensional ◽  
Parametric Modeling ◽  
Bevel Gear ◽  
Secondary Development ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Three Dimensional Modeling ◽  
Spiral Bevel

The author describes tooth profile formatting mechanism of spherical involute spiral bevel gear based on Principles of Gear conjugate, establishes the mathematical model of spiral bevel gears. The precise spherical involute of spiral bevel gears is generated with parametric modeling idea and th secondary development method based on PROGRAM of PRO/E software. Finally, a complete spherical three-dimensional modeling of the involute spiral bevel gear is established, which provides a method of parametric design and manufacturing of spiral bevel gears.

scholarly journals Effect of roller bearing elasticity on spiral bevel gear dynamics

2020 ◽  
Vol 12 (7) ◽  
pp. 168781402093889
Author(s):  
Xia Hua ◽  
Zaigang Chen
Keyword(s):  
Roller Bearing ◽  
Bevel Gear ◽  
Spiral Bevel Gear ◽  
Element Formulation ◽  
Dynamic Force ◽  
Spiral Bevel Gears ◽  
Gear Dynamics ◽  
Bevel Gears ◽  
Bearing Stiffness ◽  
Spiral Bevel

The dynamics of spiral bevel gears have gained increasing importance due to concerns relating to noise and durability. This is because the mesh force acting on the gear teeth is amplified under dynamic conditions, potentially reducing the fatigue life of the gears. Furthermore, a sizable dynamic force can be transmitted to the housing, inducing structure-born gear whine. The elasticity of the bearings can influence the dynamics of spiral bevel gears. In this article, the finite element formulation of a spiral bevel geared rotor dynamic system is applied to investigate the influence of bearing elasticity on the dynamics of spiral bevel gears. The designs and configurations of rear axles are modeled and analyzed for real-world applications, to gain an enhanced practical understanding of the effect of bearing stiffness on spiral bevel gear dynamics.

Design and analysis of high contact ratio spiral bevel gears by modified curvature motion method

2017 ◽  
Vol 232 (19) ◽  
pp. 3396-3409 ◽  
Author(s):  
Yanming Mu ◽  
Zongde Fang
Keyword(s):  
Transmission Error ◽  
Bevel Gear ◽  
Spiral Bevel Gear ◽  
Contact Ratio ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Curvature Motion ◽  
Seventh Order ◽  
Spiral Bevel ◽  
Motion Method

This paper presents a new method to design a seventh-order transmission error for high contact ratio spiral bevel gears by the modified curvature motion method to reach the purpose of reducing or eliminating gear vibration and noise. In this paper, firstly, based on the predesigned seventh-order transmission error, the polynomial coefficients of transmission error curve can be obtained. Secondly, a method named modified curvature motion method is used to generate the spiral bevel gear with the predesigned transmission error. Lastly, based on TCA and LTCA, we verify the feasibility of the modified curvature motion method to generate spiral bevel gear with seventh-order transmission error, and the meshing impact of gear set with the seventh-order and second-order function of transmission error is analyzed and compared. The results of a numerical example show that the seventh-order transmission error acquired by the modified curvature motion method can effectively reduce the meshing impact of spiral bevel gears. The tooth modification method and meshing impact analysis method can serve as a basis for developing a general technique of flank modification for spiral bevel gears.

The Undercutting of Circular-Cut Spiral Bevel Gears

1992 ◽  
Vol 114 (2) ◽  
pp. 317-325 ◽  
Author(s):  
Zhang-Hua Fong ◽  
Chung-Biau Tsay
Keyword(s):  
Gear Tooth ◽  
Sufficient Conditions ◽  
Bevel Gear ◽  
Tooth Surface ◽  
Spiral Bevel Gear ◽  
Spiral Bevel Gears ◽  
Bevel Gears ◽  
Tooth Surfaces ◽  
Sufficient And Necessary Conditions ◽  
Spiral Bevel

Undercutting is a serious problem in designing spiral bevel gears with small numbers of teeth. Conditions of undercutting for spiral bevel gears vary with the manufacturing methods. Based on the theory of gearing [1], the tooth geometry of the Gleason type circular-cut spiral bevel gear is mathematically modeled. The sufficient and necessary conditions for the existence and regularity of the generated gear tooth surfaces are investigated. The conditions of undercutting for a circular-cut spiral bevel gear are defined by the sufficient conditions of the regular gear tooth surface. The derived undercutting equations can be applicable for checking the undercutting conditions of spiral bevel gears manufactured by the Gleason Duplex Method, Helical Duplex Method, Fixed Setting Method, and Modified Roll Method. An example is included to illustrate the application of the proposed undercut checking equations.

Sign in / Sign up

Export Citation Format

Share Document