scholarly journals Sectorization for Water Distribution Systems with Multiple Sources: A Performance Indices Comparison

Water ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 131
Author(s):  
Jezabel D. Bianchotti ◽  
Melina Denardi ◽  
Mario Castro-Gama ◽  
Gabriel D. Puccini
Keyword(s):  
Distribution Systems ◽  
Water Distribution ◽  
Distribution Networks ◽  
Performance Criteria ◽  
Performance Indices ◽  
Multiple Sources ◽  
Multiobjective Problems ◽  
Open Questions ◽  
Minimum Number ◽  
And Performance

Sectorization is an effective technique for reducing the complexities of analyzing and managing of water systems. The resulting sectors, called district metering areas (DMAs), are expected to meet some requirements and performance criteria such as minimum number of intervention, pressure uniformity, similarity of demands, water quality and number of districts. An efficient methodology to achieve all these requirements together and the proper choice of a criteria governing the sectorization is one of the open questions about optimal DMAs design. This question is addressed in this research by highlighting the advantages of three different criteria when applied to real-word water distribution networks (WDNs). To this, here it is presented a two-stage approach for optimal design of DMAs. The first stage, the clustering of the system, is based on a Louvain-type greedy algorithm for the generalized modularity maximization. The second stage, the physical dividing of the system, is stated as a two-objective optimization problem that utilises the SMOSA version of simulated annealing for multiobjective problems. One objective is the number of isolation valves whereas for the second objective three different performance indices (PIs) are analyzed and compared: (a) standard deviation, (b) Gini coefficient and (c) loss of resilience. The methodology is applied to two real case studies where the first two PIs are optimized to address similar demands among DMAs. The results demonstrate that the proposed method is effective for sectorization into independent DMAs with similar demands. Surprisingly, it found that for the real studied systems, loss of resilience achieves better performance for each district in terms of pressure uniformity and demand similarity than the other two specific performance criteria.

scholarly journals Optimal placement of valves in a water distribution network with CLP(FD)

2011 ◽  
Vol 11 (4-5) ◽  
pp. 731-747 ◽  
Author(s):  
MASSIMILIANO CATTAFI ◽  
MARCO GAVANELLI ◽  
MADDALENA NONATO ◽  
STEFANO ALVISI ◽  
MARCO FRANCHINI
Keyword(s):  
Logic Programming ◽  
Distribution Systems ◽  
Water Distribution ◽  
Distribution Network ◽  
Real Life ◽  
Water Distribution Network ◽  
Distribution Networks ◽  
Constraint Logic Programming ◽  
Optimal Placement ◽  
Isolation System

AbstractThis paper presents a new application of logic programming to a real-life problem in hydraulic engineering. The work is developed as a collaboration of computer scientists and hydraulic engineers, and applies Constraint Logic Programming to solve a hard combinatorial problem. This application deals with one aspect of the design of a water distribution network, i.e., the valve isolation system design. We take the formulation of the problem by Giustolisi and Savić (2008 Optimal design of isolation valve system for water distribution networks. InProceedings of the 10th Annual Water Distribution Systems Analysis Conference WDSA2008, J. Van Zyl, A. Ilemobade, and H. Jacobs, Eds.) and show how, thanks to constraint propagation, we can get better solutions than the best solution known in the literature for the Apulian distribution network. We believe that the area of the so-calledhydroinformaticscan benefit from the techniques developed in Constraint Logic Programming and possibly from other areas of logic programming, such as Answer Set Programming.

scholarly journals Graph Neural Network for Integrated Water Network Partitioning and Dynamic District Metered Areas

2021 ◽  
Author(s):  
KEZHEN RONG ◽  
Minglei Fu ◽  
JIAWEI CHEN ◽  
LEJIN ZHENG ◽  
JIANFENG ZHENG ◽  
...  
Keyword(s):  
Neural Network ◽  
Distribution Systems ◽  
Water Distribution ◽  
Distribution Networks ◽  
Pollution Monitoring ◽  
Practical Case ◽  
Network Partitioning ◽  
Water Network ◽  
Search Range ◽  
Water Network Partitioning

Abstract Water distribution systems (WDSs) are used to transmit and distribute water resources in cities. Water distribution networks (WDNs) are partitioned into district metered areas (DMAs) by water network partitioning (WNP), which can be used for leak control, pollution monitoring, and pressure optimization in WDS management. In order to overcome the limitations of optimal search range and the decrease of recovery ability caused by two-step WNP and fixed DMAs in previous studies, this study developed a new method combining a graph neural network to realize integrated WNP and dynamic DMAs to optimize WDS management and respond to emergencies. The proposed method was tested in a practical case study; the results showed that good hydraulic performance of the WDN was maintained and that dynamic DMAs demonstrated excellent stability in emergency situations, which proves the effectiveness of the method in WNP.

scholarly journals Management of Water Distribution Systems in PDA Condition with Isolation Valves

Proceedings ◽  
2018 ◽  
Vol 2 (11) ◽  
pp. 672 ◽  
Author(s):  
Attilio Fiorini Morosini ◽  
Olga Caruso ◽  
Paolo Veltri
Keyword(s):  
Distribution Systems ◽  
Water Distribution ◽  
Distribution Networks ◽  
Optimal Number ◽  
System Control ◽  
Pipe Failure ◽  
Reliable System ◽  
Network Nodes ◽  
Pipe Burst

The correct management of Water Distribution Networks (WDNs) allows to obtain a reliable system. When a pipe failure occurs in a network and it is necessary to isolate a zone, it is possible that some nodes do not guarantee service for the users due to inadequate heads. In these conditions a Pressure Driven Analysis (PDA) is the correct approach to evaluate network behavior. This analysis is more appropriate than the Demand Driven Analysis (DDA) because it is known that the effective delivered flow at each node is influenced by the pressure value. In this case, it is important to identify a subset of isolation valves to limit disrupting services in the network. For a real network, additional valves must be added to existing ones. In this paper a new methodological analysis is proposed: it defines an objective function (OF) to provide a measure of the system correct functioning. The network analysis using the OF helps to choose the optimal number of additional valves to obtain an adequate system control. In emergency conditions, the OF takes into account the new network topology obtained excluding the zone where the broken pipe is located. OF values depend on the demand deficit caused by the head decrement in the network nodes for each pipe burst considered. The results obtained for a case study confirm the efficiency of the methodology.

scholarly journals Using real options for an eco-friendly design of water distribution systems

2014 ◽  
Vol 17 (1) ◽  
pp. 20-35 ◽  
Author(s):  
João Marques ◽  
Maria Cunha ◽  
Dragan A. Savić
Keyword(s):  
Real Options ◽  
Distribution System ◽  
Distribution Systems ◽  
Water Distribution ◽  
System Development ◽  
Water Distribution Systems ◽  
Distribution Networks ◽  
Embodied Energy ◽  
Real Options Approach ◽  
Materials Used

This paper presents a real options approach to handling uncertainties associated with the long-term planning of water distribution system development. Furthermore, carbon emissions associated with the installation and operation of water distribution networks are considered. These emissions are computed by taking an embodied energy approach to the different materials used in water networks. A simulated annealing heuristic is used to optimise a flexible eco-friendly design of water distribution systems for an extended life horizon. This time horizon is subdivided into different time intervals in which different possible decision paths can be followed. The proposed approach is applied to a case study and the results are presented according to a decision tree. Lastly, some comparisons and results are used to demonstrate the quality of the results of this approach.

scholarly journals Failure monitoring in water distribution networks

2006 ◽  
Vol 53 (4-5) ◽  
pp. 503-511 ◽  
Author(s):  
D. Misiunas ◽  
J. Vítkovský ◽  
G. Olsson ◽  
M. Lambert ◽  
A. Simpson
Keyword(s):  
Flow Rate ◽  
Distribution Systems ◽  
Water Distribution ◽  
Design Procedure ◽  
Distribution Networks ◽  
Water Distribution Networks ◽  
Pressure Monitoring ◽  
Burst Detection ◽  
Inlet Flow Rate ◽  
Failure Monitoring

An algorithm for the burst detection and location in water distribution networks based on the continuous monitoring of the flow rate at the entry point of the network and the pressure at a number of points within the network is presented. The approach is designed for medium to large bursts with opening times in the order of a few minutes and is suitable for networks of relatively small size, such as district metered areas (DMAs). The burst-induced increase in the inlet flow rate is detected using the modified cumulative sum (CUSUM) change detection test. Based on parameters obtained from the CUSUM test, the burst is simulated at a number of burst candidate locations. The calculated changes in pressure at the pressure monitoring points are then compared to the measured values and the location resulting in the best fit is selected as the burst location. The EPANET steady-state hydraulic solver is utilised to simulate the flows and pressures in the network. A sensitivity-based sampling design procedure is introduced to find the optimal positions for pressure monitoring points. The proposed algorithm is tested on a case study example network and shows potential for burst detection and location in real water distribution systems.

scholarly journals A Pressure Monitoring System for Water Distribution Networks Based on Arduino Microcontroller

Water ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2321
Author(s):  
Federica Bruno ◽  
Mauro De Marchis ◽  
Barbara Milici ◽  
Domenico Saccone ◽  
Fabrizio Traina
Keyword(s):  
Monitoring System ◽  
Distribution Systems ◽  
Water Distribution ◽  
Water Pressure ◽  
Distribution Networks ◽  
Water Utilities ◽  
Water Distribution Networks ◽  
Prototype System ◽  
Pressure Monitoring ◽  
Arduino Microcontroller

Efficient management of water distribution networks (WDNs) is currently a focal point, especially in countries where water scarcity conditions are more and more amplified by frequent drought periods. In these cases, in fact, pressure becomes the fundamental variable in managing the WDNs. Similarly, WDNs are often obsolete and affected by several points of water losses. Leakages are mainly affected by pressure; in fact, water utilities usually apply the technique of pressure management to reduce physical losses. It is clear how pressure plays a fundamental role in the management of WDNs and in water safety. Even though the technologies are quite mature, these systems are often expensive, especially if a capillarity monitoring system is required; thus, water managers apply the measurement of the flow rate and pressure at very few points. Today, the implementation of the Internet of things (IoT) can be considered a key strategy for monitoring water distribution systems. Once the sensors are installed, in fact, it is relatively easy to build a communication system able to collect and send data from the network. In the proposed study, a smart pressure monitoring system was developed using low-cost hardware and open-source software. The prototype system is composed of an Arduino microcontroller, a printed circuit board, and eight pressure transducers. The efficiency of the proposed tool was compared with a SCADA monitoring system. To investigate on the efficiency of the proposed measurement system, an experimental campaign was carried out at the Environmental Hydraulic Laboratory of the University of Enna (Italy), and hydrostatic as well as hydrodynamic tests were performed. The results showed the ability of the proposed pressure monitor tool to have control of the water pressure in a WDN with a simple, scalable, and economic system. The proposed system can be easily implemented in a real WDN by water utilities, thus improving the knowledge of pressure and increasing the efficiency level of the WDN management.

scholarly journals Online modelling of water distribution systems: a UK case study

2010 ◽  
Vol 3 (1) ◽  
pp. 21-27 ◽  
Author(s):  
J. Machell ◽  
S. R. Mounce ◽  
J. B. Boxall
Keyword(s):  
Distribution Systems ◽  
Water Distribution ◽  
Data Transfer ◽  
Simulation Models ◽  
Distribution Networks ◽  
Water Supply Systems ◽  
Full Potential ◽  
Operational Conditions ◽  
The Impact

Abstract. Hydraulic simulation models of water distribution networks are routinely used for operational investigations and network design purposes. However, their full potential is often never realised because, in the majority of cases, they have been calibrated with data collected manually from the field during a single historic time period and, as such, reflect the network operational conditions that were prevalent at that time, and they are then applied as part of a reactive, desktop investigation. In order to use a hydraulic model to assist proactive distribution network management its element asset information must be up to date and it should be able to access current network information to drive simulations. Historically this advance has been restricted by the high cost of collecting and transferring the necessary field measurements. However, recent innovation and cost reductions associated with data transfer is resulting in collection of data from increasing numbers of sensors in water supply systems, and automatic transfer of the data to point of use. This means engineers potentially have access to a constant stream of current network data that enables a new era of "on-line" modelling that can be used to continually assess standards of service compliance for pressure and reduce the impact of network events, such as mains bursts, on customers. A case study is presented here that shows how an online modelling system can give timely warning of changes from normal network operation, providing capacity to minimise customer impact.

scholarly journals Trihalomethanes in Water Supply System and Water Distribution Networks

2021 ◽  
Vol 18 (17) ◽  
pp. 9066
Author(s):  
Sornsiri Sriboonnak ◽  
Phacharapol Induvesa ◽  
Suraphong Wattanachira ◽  
Pharkphum Rakruam ◽  
Adisak Siyasukh ◽  
...  
Keyword(s):  
Water Supply ◽  
Organic Compounds ◽  
Distribution Systems ◽  
Water Distribution ◽  
Distribution Networks ◽  
Research Area ◽  
Seasonal Effects ◽  
Water Supply Systems ◽  
Treated Water ◽  
Guideline Values

The formation of trihalomethanes (THMs) in natural and treated water from water supply systems is an urgent research area due to the carcinogenic risk they pose. Seasonal effects and pH have captured interest as potential factors affecting THM formation in the water supply and distribution systems. We investigated THM occurrence in the water supply chain, including raw and treated water from water treatment plants (coagulation, sedimentation, sand filtration, ClO2-disinfection processes, and distribution pipelines) in the Chiang Mai municipality, particularly the educational institute area. The effects of two seasons, rainy (September–November 2019) and dry (December 2019–February 2020), acted as surrogates for the water quality profile and THM occurrence. The results showed that humic acid was the main aromatic and organic compound in all the water samples. In the raw water sample, we found a correlation between surrogate organic compounds, including SUVA and dissolved organic carbon (DOC) (R2 = 0.9878). Four species of THMs were detected, including chloroform, bromodichloromethane, dibromochloromethane, and bromoform. Chloroform was the dominant species among the THMs. The highest concentration of total THMs was 189.52 μg/L. The concentration of THMs tended to increase after chlorination when chlorine dioxide and organic compounds reacted in water. The effect of pH on the formation of TTHMs was also indicated during the study. TTHM concentrations trended lower with a pH ≤ 7 than with a pH ≥ 8 during the sampling periods. Finally, in terms of health concerns, the concentration of TTHMs was considered safe for consumption because it was below the standard (<1.0) of WHO’s Guideline Values (GVs).

Sign in / Sign up

Export Citation Format

Share Document