A case study in the measurement of door sound isolation with ASTM test standards

2021 ◽  
Vol 263 (3) ◽  
pp. 3504-3510
Author(s):  
Christopher Ono ◽  
Todd Beiler ◽  
Devin Clausen
Keyword(s):  
Sound Transmission ◽  
Test Methods ◽  
Sound Insulation ◽  
Performance Requirement ◽  
Test Standards ◽  
Critical Design ◽  
Minimum Requirements ◽  
Sound Transmission Class ◽  
Testing Standards

The use of the door transmission class rating in lieu of the apparent sound transmission class rating has yet to gain traction within building codes and specified project requirements. This paper presents a case study involving performance requirement testing conducted at a university's media facility, in which sound insulation properties were a critical design and construction focus. Both test methods described in ASTM E2964 and ASTM E336 were performed where a door was the test partition. Door transmission class ratings were presented in comparison to apparent sound transmission class ratings for the same partition. Testing was performed in a variety of situations, including scenarios both inside and outside of the minimum requirements of testing standards. Our analysis considers the effectiveness of the recently adopted ASTM E2964 in comparison to the methods of the ASTM E336. We also consider some of the subtle differences between the two test methods and how they may impact the testing of certain adjacencies.

Parameters and Methods for Testing Artificial Heart Valves

1989 ◽  
Vol 12 (4) ◽  
pp. 252-260 ◽  
Author(s):  
J.C. Köhler ◽  
J.G. Tech
Keyword(s):  
Heart Valves ◽  
Close Correlation ◽  
Test Methods ◽  
In Vitro Tests ◽  
Geometrical Parameters ◽  
Test Standards ◽  
Artificial Heart Valves ◽  
Minimum Requirements ◽  
Definition Of

The report describes the development of heart valve test standards. The aim is comprehensive quality assurance by in vitro tests. The project includes three test fields: general basis, development and definition of test methods and test devices and comparative in vitro assessment of valves for the definition of minimum requirements. A preliminary list of test parameters and test steps has been defined: geometrical, flow, deformation, force, and conditioning parameters. A system of geometrical parameters has been developed for standardized aortic models. Geometrical parameters of 31 valves of six types and different sizes underline a close correlation between geometrical and hemodynamic parameters. The relative ostium cross-section Ae/AT increases with valve size and lies between 0.3 and 0.5. Two new measurement devices with quasi-steady flow are proposed as quick testers for leakage flow and pressure loss.

Acoustic design tools for estimation of sound insulation performance of wood wall and floor assemblies

2021 ◽  
Vol 263 (6) ◽  
pp. 267-274
Author(s):  
Cheng Qian ◽  
Lin Hu ◽  
Christian Dagenais ◽  
Sylvain Gagnon
Keyword(s):  
Prediction Models ◽  
National Research Council ◽  
Design Tool ◽  
Sound Insulation ◽  
Prediction Tools ◽  
Minimum Requirements ◽  
Sound Transmission Class ◽  
Interior Walls ◽  
The Impact ◽  
Insulation Performance

The National Building Code of Canada 2015 stipulates the minimum requirements of the airborne sound insulation transmission through common interior walls and ceiling/floor assemblies. The required minimum Apparent Sound Transmission Class (ASTC) is 47 in Canada, whereas the Impact Insulation Class (IIC) for floors is recommended to be higher than 55. For many years, significant efforts were made to develop sound insulation prediction models or tools to predict the sound insulation performance of wall and floor/ceiling assemblies at the design phase in order to meet the requirements and the recommendations made by codes. However, today few models can provide a reliable acoustics design tool. In this document, three prediction tools thought to be practically useful are presented and evaluated. Between these three prediction tools, one is an analytical model of the Insul software while the other two are empirical models developed by the National Research Council of Canada and the American Wood Council. This paper compared the STC and IIC ratings of wood wall and floor assemblies estimated by these three models and verified them by the measured STC and IIC ratings. This work aims at providing an idea for readers to choose a suitable design tool to proceed with their acoustic designs.

Characterizing the Sound Insulation of a Specially Orthotropic Multi-Layered Medium

2007 ◽  
Vol 23 (1) ◽  
pp. 63-68 ◽  
Author(s):  
H.-J. Lin ◽  
C.-N. Wang ◽  
Y.-M. Kuo
Keyword(s):  
Boundary Conditions ◽  
Sound Propagation ◽  
Transmission Loss ◽  
Sound Transmission ◽  
Single Layer ◽  
Sound Insulation ◽  
Sound Transmission Loss ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Sound Transmission Class

AbstractThis work explores the sound transmission loss provided by the orthotropic multi-layers to elucidate the sound insulation of FRP (Fiber Reinforced Plastics). Mat is the major material considered in the numerical works. The transfer matrices of a single layer of the orthotropic laminate and the fluid are determined. Further, the boundary conditions on the various interface planes are arranged into matrix form. Combining the transfer matrixes and the boundary conditions and applying the transfer matrix method (TMM) yields the surface impedance and the sound transmission loss. The sound-propagation characteristics are studied. Additionally, the STC (Sound Transmission Class) of FRP and steel are compared and discussed.

Fidelity of J1269 and J24523

2007 ◽  
Vol 35 (2) ◽  
pp. 94-117 ◽  
Author(s):  
James A. Popio ◽  
John R. Luchini
Keyword(s):  
Steady State ◽  
Rolling Resistance ◽  
Test Methods ◽  
The Other ◽  
Reference Condition ◽  
Test Standards

Abstract This study compares data from the two Society of Automotive Engineers test methods for rolling resistance: J-2452 (Stepwise Coast-Down) and J-1269 (Equilibrium) steady state. The ability of the two methods to evaluate tires was examined by collecting data for 12 tires. The data were analyzed and the data showed that the two methods ranked the tires the same after the data were regressed and the rolling resistance magnitude was calculated at the Standard Reference Condition. In addition, analysis of the two methods using this matched set of testing provided an opportunity to evaluate each of these test standards against the other. It was observed that each test has merits absent from the other.

scholarly journals Analysis of the transmission loss of double-leaf panels with an equivalent spring–mass model for studs

2020 ◽  
Vol 37 ◽  
pp. 126-133
Author(s):  
Yuan-Wei Li ◽  
Chao-Nan Wang
Keyword(s):  
Distribution Curve ◽  
Transmission Loss ◽  
Sound Transmission ◽  
Experimental Results ◽  
Sound Insulation ◽  
Sound Transmission Loss ◽  
Mass Model ◽  
Steel Stud ◽  
Panel Thickness ◽  
Stiffness Distribution

Abstract The purpose of this study was to investigate the sound insulation of double-leaf panels. In practice, double-leaf panels require a stud between two surface panels. To simplify the analysis, a stud was modeled as a spring and mass. Studies have indicated that the stiffness of the equivalent spring is not a constant and varies with the frequency of sound. Therefore, a frequency-dependent stiffness curve was used to model the effect of the stud to analyze the sound insulation of a double-leaf panel. First, the sound transmission loss of a panel reported by Halliwell was used to fit the results of this study to determine the stiffness of the distribution curve. With this stiffness distribution of steel stud, some previous proposed panels are also analyzed and are compared to the experimental results in the literature. The agreement is good. Finally, the effects of parameters, such as the thickness and density of the panel, thickness of the stud and spacing of the stud, on the sound insulation of double-leaf panels were analyzed.

On Integration of Additive Manufacturing During the Design and Development of a Rehabilitation Robot: A Case Study

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Kaci E. Madden ◽  
Ashish D. Deshpande
Keyword(s):  
Additive Manufacturing ◽  
Neurological Disorders ◽  
Development Process ◽  
Mechanical Design ◽  
Rehabilitation Robotics ◽  
Critical Design ◽  
Rehabilitation Robots ◽  
Time Optimization ◽  
Hand Exoskeleton

The field of rehabilitation robotics has emerged to address the growing desire to improve therapy modalities after neurological disorders, such as a stroke. For rehabilitation robots to be successful as clinical devices, a number of mechanical design challenges must be addressed, including ergonomic interactions, weight and size minimization, and cost–time optimization. We present additive manufacturing (AM) as a compelling solution to these challenges by demonstrating how the integration of AM into the development process of a hand exoskeleton leads to critical design improvements and substantially reduces prototyping cost and time.

Analytical higher-order-theories for noise reduction analysis of viscoelastic composite multilayered shells

2021 ◽  
pp. 095440622098233
Author(s):  
A Alaimo ◽  
C Orlando ◽  
S Valvano
Keyword(s):  
Sound Transmission ◽  
Higher Order ◽  
Sound Insulation ◽  
Viscoelastic Layer ◽  
Multilayered Structures ◽  
Viscoelastic Composite ◽  
Damping Behavior ◽  
Shell Models ◽  
Composite Layers ◽  
Insulation Effect

The noise transmission of aeronautical panels is an important phase of the design process of an airplane. In this work an analytical Navier-type solution, based on higher-order layer-wise shell models, is proposed for the analysis of the sound insulation of laminated panels. The considered multilayered structures are laminated with cross-ply composite layers embedded with interlaminar viscoelastic sheets. The use of the soft interlayers permits to have a passive insulation effect in the study of the sound transmission. In order to take into account the frequency depedent properties of a realistic viscoelastic layer, the damping behavior is modeled through a fractional derivative Zener model. The Rayleigh integral method is used to extrapolate the acoustic indicators for the sound transmission analysis. Some results are presented to validate the efficiency of the present approach, comparing the present solutions with others taken from the literature.

Sign in / Sign up

Export Citation Format

Share Document