scholarly journals Evaluation of Mechanical Properties of AA7075 /Al2O3/Mg Hybrid Composites

2019 ◽  
Vol 8 (6) ◽  
pp. 5044-5046 ◽  
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composites ◽  
Casting Process ◽  
Stir Casting ◽  
Tensile Behaviour ◽  
Matrix Composites ◽  
Compression Behavior ◽  
Weight Percentage ◽  
Fea Simulation ◽  
Alloy Metal

The present work was planned to evaluate the mechanical properties of alumina reinforced aluminium alloy such hardness and compression behavior of al2o3 /aa7075 alloy metal matrix composites. Both, experimental and finite element analyses were carried out to establish tensile behaviour of the composites with different weight percentage of al2o3 fabricated by the stir casting process. The results concluded that addition of alumina to the aa7075 improves the mechanical properties of the composite. Further the results of FEA simulation of the composites are close to the actual results which shows that cost and time can be reduced if FEA is performed

scholarly journals Investigation on Mechanical and Wear Behaviors of LM6 Aluminium Alloy-Based Hybrid Metal Matrix Composites Using Stir Casting Process

2022 ◽  
Vol 2022 ◽  
pp. 1-10
Author(s):  
P. Gnaneswaran ◽  
V. Hariharan ◽  
Samson Jerold Samuel Chelladurai ◽  
G. Rajeshkumar ◽  
S. Gnanasekaran ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Wear Resistance ◽  
Steel Fiber ◽  
Hybrid Composites ◽  
Casting Process ◽  
Stir Casting ◽  
Image Analyzer ◽  
Matrix Composites ◽  
Silicon Based ◽  
Boron Carbide B4c

In this investigation, aluminium-silicon-based alloy (LM6) with the addition of (0, 2.5, 5, and 10%) copper-coated short steel fiber and 5% boron carbide (B4C) element-strengthened composites was fabricated by the stir casting method. Mechanical properties and tribological behaviors of LM6-based hybrid composites were investigated, and microstructures of different castings were examined by an image analyzer. The test was conducted at different loads (10, 20, 30, and 40 N) and different sliding spaces (500, 1000, 1500, and 2000 m), respectively. The results revealed that the sample loaded with 10% of reinforcement recorded the highest tensile strength of 231 MPa. On the other hand, the hardness value increased from 71 to 144 BHN, when 15% of reinforcement was added to the sample. It was also noted that 10% copper-coated steel fiber improved wear resistance up to 50% when compared to LM6. A field emission scanning electron microscope was employed to observe the morphology of the worn surfaces of composites at different sliding distances and load conditions. The hybrid composite revealed that the combination of both short steel fibers and reinforcement of ceramic particles enhanced the mechanical properties, obtaining superior wear resistance.

Preparation and Mechanical Characterization of Stir Cast Hybrid Al7075-Al2O3 -B4C Metal Matrix Composites

2014 ◽  
Vol 592-594 ◽  
pp. 705-710 ◽  
Author(s):  
S. Dhanalakshmi ◽  
N Mohanasundararaju ◽  
P.G. Venkatakrishnan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Hybrid Composites ◽  
Stir Casting ◽  
Matrix Composites ◽  
Constant Weight ◽  
Weight Percentage

A hybrid Al7075 metal matrix composites have been fabricated through liquid metallurgy route (Stir Casting method) using Al2O3 and B4C as reinforcement materials. The effect of weight percentage of reinforcement materials on mechanical properties of the composites have been studied by varying the weight percentage of Al2O3 as 3, 6, 9, 12 and 15% while keeping constant weight percentage of B4C (3%). The as-cast microstructure, tensile strength, micro and macro hardness of the fabricated hybrid composites have been studied. The mechanical properties of the prepared composites were increased with increasing the weight percentage of the reinforcement in the composite. The maximum tensile strength, micro-hardness and macro-hardness of 309 MPa, 140 VHN, and 112 BHN, respectively, were obtained for a hybrid Al7075 matrix composite containing 15% Al2O3 and 3% B4C.

Experimental Investigation of Mechanical Properties of Ceramic Reinforced Al-7075 Metal Matrix Hybrid Composites

2020 ◽  
Vol 979 ◽  
pp. 34-39
Author(s):  
K. Sudhindra Srinivas ◽  
M. Murali Mohan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Metal Matrix ◽  
Hybrid Composites ◽  
Experimental Studies ◽  
Stir Casting ◽  
Matrix Composites ◽  
Weight Percentage ◽  
Particulate Metal ◽  
Al 7075

The epidemic adoption of particulate metal matrix composites (MMCs) for engineering applications has been delay by the high cost of producing components of even minimally complex shape. The aluminum-based composites find its applications widely in transport, aerospace, marine, automobile and mineral processing industries, owing to their improved strength, stiffness and wear resistance properties. This paper, presents the overview of the addition of different reinforcements to aluminium alloy. The reinforcements are added to the Al7075 by using stir casting method. Effect of these reinforcements like Titanium carbide (TiC) and silicon (Si) influencing on the mechanical properties like tensile strength, hardness was studied. Research relevant to these factors which influence particles distribution were noticed by conducting the experimental studies of Al7075 hybrid composites.The mechanical properties and the microstructure of Al–TiC-Si metal matrix composite has shown the significant improvement in Hardness and Tensile strength, with increase in TiC and Si particles in weight percentage of composites.

Influence of Sic and Al2O3 Particulate Reinforcement on the Mechanical Properties of ZA27 Metal Matrix Composites

2019 ◽  
Vol 969 ◽  
pp. 122-127
Author(s):  
B.N. Anjan ◽  
G.V. Preetham Kumar
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Matrix Alloy ◽  
Stir Casting ◽  
Matrix Composites ◽  
Reinforced Composites ◽  
Weight Percentage ◽  
Casting Technique ◽  
Fine Microstructure ◽  
Properties Of Composites

Zinc aluminum based matrix composites reinforced with SiC and Al2O3 particles have significant applications in the automobile field. Stir casting method followed by squeeze process was used for fabrication. ZA27 composites reinforced with SiC and Al2O3 particles (20-50µm) in various weight percentage (wt%) ranges from 0-10 in a step of 5 each was fabricated. OM, SEM and EDS analysis of microstructures obtained for matrix alloy and reinforced composites were performed in order to know the effect of varying wt% on physical and mechanical properties of composites. Squeeze casting technique shows better features such as fine microstructure as a result of low porosity and good bonding between matrix and reinforcement. Addition of reinforcements decreased the densities of matrix alloy. SiC reinforced composites showed better results as compared with Al2O3 reinforced ones. Hardness and ultimate tensile strength value of 10 wt% reinforced composites showed improved results.

Synthesis and Characterization of Al 7075 Alloy Reinforced with Silicon Carbide and Fly Ash

2019 ◽  
Vol 11 (3) ◽  
Author(s):  
G. Sathishkumar ◽  
S.J. Irudayaraja ◽  
S. Sivaganesan ◽  
M. Thuyavan
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Casting Process ◽  
Stir Casting ◽  
Industrial Applications ◽  
Matrix Composites ◽  
Specific Strength ◽  
Al 7075 ◽  
7075 Alloy

Metal matrix composites are of great interest in industrial applications for its light weight with high specific strength, stiffness and heat resistance. The processing of MMCs by stir casting process is an effective way of manufacturing. In this paper the comparison of mechanical properties of Aluminium 7075 as a base metal and varying composition of fly ash by 3 and 6 wt.% SiC and 7% fly ash as reinforcement is carried out. Scanning electron microscope was used to confirm the presence of SiC and fly ash. The composites with 6% SiC was found to have maximum hardness whereas composites of 6% and 5 % fly ash were found to have minimum hardness. The mechanical properties such as wear resistance were studied. From the results, it has been finalized that the addition of 6% SiC was identified to show the least wear rate.

Study on Mechanical Properties of Al 7075 Hybrid Metal Matrix Composites

2015 ◽  
Vol 813-814 ◽  
pp. 230-234 ◽  
Author(s):  
T.S.A. Suryakumari ◽  
S. Ranganathan ◽  
P. Shankar
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Stir Casting ◽  
Impact Loads ◽  
Matrix Composites ◽  
Casting Method ◽  
Weight Percentage ◽  
Hybrid Metal Matrix Composites ◽  
Al 7075

The present investigation involves studying the mechanical properties of the fabricated aluminium 7075 hybrid metal matrix composites reinforced with various weight % of SiC and Al2 O3 particulates by stir casting method. The Al 7075 hybrid metal matrix composites specimen were fabricated using L9 orthogonal array. The mechanical properties like Brinell Harness (BHN), Rockwell Hardness (HRC) and impact loads were experimented. The mechanical properties like hardness and impact loads have improved with the increase in weight percentage of SiC and Al2O3 particulates in the hybrid aluminium matrix.

Sign in / Sign up

Export Citation Format

Share Document