Synthesis and Characterization of Al 7075 Alloy Reinforced with Silicon Carbide and Fly Ash

2019 ◽  
Vol 11 (3) ◽  
Author(s):  
G. Sathishkumar ◽  
S.J. Irudayaraja ◽  
S. Sivaganesan ◽  
M. Thuyavan
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Casting Process ◽  
Stir Casting ◽  
Industrial Applications ◽  
Matrix Composites ◽  
Specific Strength ◽  
Al 7075 ◽  
7075 Alloy

Metal matrix composites are of great interest in industrial applications for its light weight with high specific strength, stiffness and heat resistance. The processing of MMCs by stir casting process is an effective way of manufacturing. In this paper the comparison of mechanical properties of Aluminium 7075 as a base metal and varying composition of fly ash by 3 and 6 wt.% SiC and 7% fly ash as reinforcement is carried out. Scanning electron microscope was used to confirm the presence of SiC and fly ash. The composites with 6% SiC was found to have maximum hardness whereas composites of 6% and 5 % fly ash were found to have minimum hardness. The mechanical properties such as wear resistance were studied. From the results, it has been finalized that the addition of 6% SiC was identified to show the least wear rate.

scholarly journals Evaluation of Mechanical Properties of AA7075 /Al2O3/Mg Hybrid Composites

2019 ◽  
Vol 8 (6) ◽  
pp. 5044-5046 ◽  
Keyword(s):  
Mechanical Properties ◽  
Hybrid Composites ◽  
Casting Process ◽  
Stir Casting ◽  
Tensile Behaviour ◽  
Matrix Composites ◽  
Compression Behavior ◽  
Weight Percentage ◽  
Fea Simulation ◽  
Alloy Metal

The present work was planned to evaluate the mechanical properties of alumina reinforced aluminium alloy such hardness and compression behavior of al2o3 /aa7075 alloy metal matrix composites. Both, experimental and finite element analyses were carried out to establish tensile behaviour of the composites with different weight percentage of al2o3 fabricated by the stir casting process. The results concluded that addition of alumina to the aa7075 improves the mechanical properties of the composite. Further the results of FEA simulation of the composites are close to the actual results which shows that cost and time can be reduced if FEA is performed

Fabrication and Characterization of A356-Basalt Ash-Fly Ash Composites Processed by Stir Casting Method

2017 ◽  
Vol 25 (3) ◽  
pp. 209-214 ◽  
Author(s):  
G. Venkatachalam ◽  
A. Kumaravel
Keyword(s):  
Fly Ash ◽  
Impact Strength ◽  
Hybrid Composites ◽  
Cost Effective ◽  
Weight Fraction ◽  
Stir Casting ◽  
Matrix Composites ◽  
Casting Method ◽  
The Matrix

This paper presents the characterization of A356 composite reinforced with fly ash and basalt ash produced by stir casting method. Aluminium metal matrix composites (AMC) are used in wide variety of applications such as structural, aerospace, marine, automotive etc. Stir casting is cost effective manufacturing process and it is useful to enhance the attractive properties of AMCs. Three sets of hybrid AMC are prepared by varying the weight fraction of the reinforcements (3% basalt + 7% fly ash, 5% basalt + 5% fly, 7% basalt + 3% fly ash). The effect of reinforcements on the mechanical properties of the hybrid composites such as hardness, tensile, compressive and impact strength were studied. The obtained results reveal that tensile, compressive and impact strength was increased when weight fraction of fly ash increased, whereas the hardness increases when weight fraction of the basalt ash increased. Microscopic study reveals the dispersion of the reinforcements in the matrix.

Investigation of mechanical properties and tribological performance of Al-LSP and Al-Al2O3 composite

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Lokanadham Dharmana ◽  
Venkata Subbaiah Kambagowni
Keyword(s):  
Mechanical Properties ◽  
Optimal Condition ◽  
Casting Process ◽  
Stir Casting ◽  
Tribological Performance ◽  
Connecting Rod ◽  
Content Type ◽  
Specific Strength ◽  
Error Band ◽  
Structural Applications

Purpose This study aims to develop the Al-Si-Mg metal matrix composite, reinforced distinctly with lime stone powder (LSP; 12% by weight) and Al2O3 (12% by weight), and compare their mechanical properties and tribological performance. Design/methodology/approach The composites are fabricated through stir casting process. In view of the previous work, the Al-LSP composite with LSP reinforcement (12 Wt.%) shows enhanced mechanical properties and tribological performance, as compared with other weight percentages. Findings Though the Al-LSP composite is less expensive, it shows similar hardness, tensile strength and specific strength, when compared with Al- Al2O3 composite. However, the Al-LSP composite exhibits significant enhancement of above three properties, when compared with Al-Si-Mg metal. The systematic factorial design of experiments is obtained through Taguchi OA [L9]. The tribological performance is estimated through wear rate (WR-mm3/m) and coefficient of friction (CF) by varying the operating parameters of sliding distance (SD), load (L) and sliding velocity (SV). According to ANOVA results, the optimal condition of WR for all the tested materials is L1SD3SV1. Further, the optimal condition of CF is L1SD1SV3 for Al-LSP and Al-Si-Mg metal, while L2SD3SV2 is for Al-Al2O3 composite. The regression equation predicts the measured experimental values within error band of ± 8 percentage. Originality/value A comparison of two composite materials (Al-LSP and Al-Al2O3) with same weight fractions (12%) shows almost same trend in both the mechanical and tribological testing process. However, the developed Al-LSP composite exhibited better properties than the Al-Al2O3 and Al-base. Therefore, Al-LSP can be suggested for automotive applications (i.e., connecting rod, cylinder liners, camshaft) and structural applications (such as frames, over hanging supports), without compromising in desirable original with properties of constituents in the new material, which is achievable for looking to the end uses.

scholarly journals Microstructure evaluation, thermal and mechanical characterization of hybrid metal matrix composite

2018 ◽  
Vol 25 (6) ◽  
pp. 1187-1196 ◽  
Author(s):  
Shyam Lal ◽  
Sudhir Kumar ◽  
Zahid A. Khan
Keyword(s):  
Metal Matrix Composite ◽  
Matrix Composite ◽  
Metal Matrix ◽  
Casting Process ◽  
Xrd Analysis ◽  
Stir Casting ◽  
Al 7075 ◽  
Dta Analysis ◽  
Hybrid Metal Matrix Composite ◽  
7075 Alloy

AbstractIn this paper, an inert gas assisted electromagnetic stir casting process is adapted for manufacturing a cast hybrid metal matrix composite (MMC) using Al2O3 and SiC particulates as a hard phase reinforcement in Al 7075 alloy metal matrix. Four different samples containing 5, 10, 15 and 20 wt% of Al2O3 and SiC with Al 7075 alloy composites were fabricated. The characterizations for all the samples were carried out through optical microstructure, scanning electron microscopy (SEM) fractograph, X-ray diffraction (XRD) analysis, differential thermal analysis (DTA) analysis and mechanical properties. The results revealed that the particles are uniformly distributed in the matrix. No peaks of Al4C3 were found. There is negligible loss of material in the composite. The tensile strength and microhardness of the hybrid composite are higher by 65.7% and 13.5%, respectively, when compared to its cast metal matrix Al 7075 alloy.

Study on Mechanical Properties of Al 7075 Hybrid Metal Matrix Composites

2015 ◽  
Vol 813-814 ◽  
pp. 230-234 ◽  
Author(s):  
T.S.A. Suryakumari ◽  
S. Ranganathan ◽  
P. Shankar
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Stir Casting ◽  
Impact Loads ◽  
Matrix Composites ◽  
Casting Method ◽  
Weight Percentage ◽  
Hybrid Metal Matrix Composites ◽  
Al 7075

The present investigation involves studying the mechanical properties of the fabricated aluminium 7075 hybrid metal matrix composites reinforced with various weight % of SiC and Al2 O3 particulates by stir casting method. The Al 7075 hybrid metal matrix composites specimen were fabricated using L9 orthogonal array. The mechanical properties like Brinell Harness (BHN), Rockwell Hardness (HRC) and impact loads were experimented. The mechanical properties like hardness and impact loads have improved with the increase in weight percentage of SiC and Al2O3 particulates in the hybrid aluminium matrix.

Sign in / Sign up

Export Citation Format

Share Document