scholarly journals Charts for Sizing Surge Anticipating Valve in Rising Mains

2020 ◽  
Vol 9 (7) ◽  
pp. 316-322
Keyword(s):  
Transient Analysis ◽  
Cost Effective ◽  
Water Hammer ◽  
Design Guidelines ◽  
Protection Device ◽  
Analysis Software ◽  
Protection Devices ◽  
Surge Protection ◽  
Selection Of

Transient analysis for large rising mains is performed to protect them from worst effects of water hammer. It requires costly surge analysis software for analysing system for surge & sizing surge protection devices. If software is not available, engineers requires, selection charts or formulae pertaining to quick sizing of surge protection device for given pumping main. If size of surge protection device is known suitable cost shall be considered in budgetary estimates. Surge anticipating valve is a cost effective, compact & reliable surge protection device used in pumping mains. It is installed on delivery manifold of the pump. There are no design guidelines or selection charts available by valve manufacturers for selection of surge anticipating valves. Hence in this paper, charts are prepared to estimate amount of surge & size of surge anticipating valve using KYPIPE TranSurge software after numerous analysis of pumping mains for various combinations of flows, diameters, elevations and lengths. In the end, software results are validated by comparing it with results obtained by experiment.

scholarly journals Matching calculation of accidental movement protection device for elevator Car

2021 ◽  
Vol 2083 (4) ◽  
pp. 042088
Author(s):  
Zhihui Zhao
Keyword(s):  
Theoretical Calculation ◽  
Basic Principle ◽  
Parameter Selection ◽  
Protection System ◽  
Protection Device ◽  
Whole Process ◽  
Protection Devices ◽  
Feasible Solutions ◽  
Selection Of

Abstract The cage accidental movement protection system is an important protection system of elevator. The basic principle and structure of the cage accidental movement protection device are described. Combined with the whole process from accidental movement of the cage to the operation of the protection device, the theoretical calculation and judgment principle of the accidental movement of the cage protection device are introduced. Aiming at the requirement of the matching calculation of the accidental movement protection of elevator car, the selection of several key parameters which affect the matching calculation of the accidental movement protection of elevator car was proposed. The influence of several key parameters on the matching calculation is analyzed, and the parameter selection is discussed based on relevant standards, and feasible solutions are proposed. These schemes provide a reference for the selection and matching calculation of accidental movement protection devices.

Medical Literature Searches -How Many Bibliographic Databases are Needed for Sufficient Retrieval in Medical Topics?

1985 ◽  
Vol 24 (03) ◽  
pp. 163-165 ◽  
Author(s):  
K. John
Keyword(s):  
Medical Literature ◽  
Cost Effective ◽  
Medical Faculty ◽  
Bibliographic Databases ◽  
Literature Searches ◽  
Selection Of

SummaryAs many bibliographic services in medicine are offered, literature searches in eight databases at DIMDI were performed to find out which database is most important in medicine. The distribution of publications from members of the medical faculty of Frankfurt University was examined. No save prediction is possible as to which database will yield most articles. Overlapping from different databases is often rather low. The selection of an appropriate database mix for sufficient recall and in a cost-effective manner.is a task for an experienced searcher.

Teknologi Esktrasi dan Cara Pemisahannya untuk Mendapatkan Kembali Karotenoid dari Minyak Sawit : Suatu Tinjauan

2016 ◽  
Vol 9 (1) ◽  
pp. 80-95
Author(s):  
Agus Sudibyo ◽  
Sardjono Sardjono
Keyword(s):  
Vitamin A ◽  
Palm Oil ◽  
Beta Carotene ◽  
Cost Effective ◽  
Raw Material ◽  
Extraction And Separation ◽  
Molecular Product ◽  
Industrial Use ◽  
Palm Oil Mill ◽  
Selection Of

Crude palm oil (CPO)is the richest natural plant source of carotenoids in terms of retinol (pro-vitamin A) equivalent, whereas palm oil mill effluent (POME) is generated from palm oil industry that contains oil and carotenes that used to be treated before discharge. Carotenoids are importance in animals and humans for the purpose of the enhancement of immune response, conversion of vitamin A and scavenging of oxygen radicals. This component has different nutritional  functions and benefits to humaan health. The growing interest in the other natural sources of beta-carotene and growing awareness to prevent pollution has stimulated the industrial use of CPO and POME as a raw material for carotenoids extraction. Various technologies of extraction and separation have been developed in order to recover of carotenoids.This article reports on various technologies that have been developed in order to recover of carotenoids from being destroyed in commercial refining of palm oil and effects of some various treatments on the extraction end separation for carotenoid from palm oil and carotenoids concentration. Principally, there are different technologies, and there is one some future which is the use of solvent. Solvent plays important role  in the most technologiest, however the problem of solvents which are used is that they posses potentiaal fire health and environmental hazards. Hence selection of the  most safe, environmentally friendly and cost effective solvent is important to design of alternative extraction methods.Chemical molecular product design is one of the methods that are becoming more popular nowadays for finding solvent with the desired properties prior to experimental testing.ABSTRAKMinyak sawit kasar merupakan sumber karotenoid terkaya yang berasal dari tanaman sawit sebagai senyawa yang sama dengan retinol atau pro-vitamin A; sedangkan limbah pengolahan minyak sawit dihasilkan dari industri pengolahan minyak sawit yang berisi minyak dan karotene yang perlu diberi perlakuan terlebih dahulu sebelum dibuang. Karotenoid merupakan bahan penting yang diperlukan pada hewan dan manusia guna memperkuat tanggapan terhadap kekebalan, konversi ke vitamin A dan penangkapan gugus oksigen radikal. Dengan berkembangnya ketertarikan dalam mencari beta-karotene yang bersumber dari alam lain dan meningkatnya kesadaran untuk mencegah adanya pencemaran lingkungan, maka mendorong suatu industri untuk menggunakan CPO dan POME sebagai bahan baku untuk diekstrak karotenoidnya. Berbagai macam teknologi guna mengekstrak dan memisahkan karotenoid telah dikembangkan untuk mendapatkan kembali karotenoidnya. Makalah ini melaporkan dan membahas berbagai jenis teknologi yang telah dikembangkan guna mendapatkan kembali senyawa karotenoid dari kerusakan di dalam proses pemurnian minyak sawit secara komersial dan pengaruh beberapa perlakuan terhadap ekstrasi dan pemisahan karotenoid dari minyak sawit dan konsentrasi karotenoidnya. Pada prinsipnya, berbagai teknologi yang digunakan untuk mengekstrak dan memisahkan karotenoid terdapat perbedaan, dan terdapat salah satu teknologi yang digunakan untuk esktrasi dan pemisahan karotenoid adalah menggunakan bahan pelarut. Pelarut yang digunakan mempunyai peranan yang penting dalam teknologi ekstrasi; namun pelarut yang digunakan untuk mengekstrak tersebut mempunyai persoalan karena berpotensi mengganggu kesehatan dan membahayakan cemaran lingkungan. Oleh karena itu, pemilihan jenis teknologi yang aman, ramah terhadap lingkungan dan biaya yang efektif untuk penggunaan pelarut merupakan hal penting sebelum dilakukan desain metode/teknologi alternatif untuk esktrasi karotenoid. Pola produk molekuler kimia merupakan salah satu metode yang saat ini menjadi lebih populer untuk mencari pelarut dengan sifat-sifat yang dikehendaki sebelum diujicobakan. Kata kunci :    karotenoid, ekstrasi, pemisahan, teknologi, minyak sawit kasar, limbah industri pengolahan sawit.

Fracture-Tolerant and Shear-Resistant Interlayers for Mitigation of Reflective Cracking

2019 ◽  
Vol 2673 (10) ◽  
pp. 35-46
Author(s):  
Cristian Cocconcelli ◽  
Bongsuk Park ◽  
Jian Zou ◽  
George Lopp ◽  
Reynaldo Roque
Keyword(s):  
Asphalt Pavement ◽  
Aggregate Size ◽  
Cost Effective ◽  
Design Guidelines ◽  
Reflective Cracking ◽  
Rubber Membrane ◽  
Near Surface ◽  
Field Evidence ◽  
Cracking Performance ◽  
Interface Cracking

Reflective cracking is frequently reported as the most common distress affecting resurfaced pavements. An asphalt rubber membrane interlayer (ARMI) approach has been traditionally used in Florida to mitigate reflective cracking. However, recent field evidence has raised doubts about the effectiveness of the ARMI when placed near the surface, indicating questionable benefits to reflective cracking and increased instability rutting potential. The main purpose of this research was to develop guidelines for an effective alternative to the ARMI for mitigation of near-surface reflective cracking in overlays on asphalt pavement. Fourteen interlayer mixtures, covering three aggregate types widely used in Florida, and two nominal maximum aggregate sizes (NMAS) were designed according to key characteristics identified for mitigation of reflective cracking, that is, sufficient gradation coarseness and high asphalt content. The dominant aggregate size range—interstitial component (DASR-IC) model was used for the design of all mixture gradations. A composite specimen interface cracking (CSIC) test was employed to evaluate reflective cracking performance of interlayer systems. In addition, asphalt pavement analyzer (APA) tests were performed to determine whether the interlayer mixtures had sufficient rutting resistance. The results indicated that interlayer mixtures designed with lower compaction effort, reduced design air voids, and coarser gradation led to more cost-effective fracture-tolerant and shear-resistant (FTSR) interlayers. Therefore, preliminary design guidelines including minimum effective film thickness and maximum DASR porosity requirements were proposed for 9.5-mm NMAS (35 µm and 50%) and 4.75-mm NMAS FTSR mixtures (20 µm and 60%) to mitigate near-surface reflective cracking.

scholarly journals Design Considerations and Selection of Cost-Effective Switched Reluctance Drive for Radiator Cooling Fans

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 917
Author(s):  
Ickjin Son ◽  
Grace Firsta Lukman ◽  
Mazahir Hussain Shah ◽  
Kwang-Il Jeong ◽  
Jin-Woo Ahn
Keyword(s):  
Low Cost ◽  
Cost Effective ◽  
Magnetic Characteristics ◽  
Switched Reluctance Motors ◽  
Switched Reluctance ◽  
Design Considerations ◽  
Cooling Fan ◽  
Cooling Fans ◽  
Power Switches ◽  
Selection Of

Switched reluctance motors (SRMs) are simple in structure, easy to manufacture, magnet-less, brushless, and highly robust compared to other AC motors which makes them a good option for applications that operate in harsh environment. However, the motor has non-linear magnetic characteristics, and it comes with various pole-phase combinations and circuit topologies that causes many difficulties in deciding on which type to choose. In this paper, the viability of SRM as a low-cost, rugged machine for vehicle radiator cooling fan is considered. First, necessary design considerations are presented, then three commonly use types of SRM are analyzed: A 3-phase 6/4, 3-phase 12/8, and a 4-phase 8/6 to find their static and dynamic characteristics so the most suitable type can be selected. Simulation results show that the 8/6 SRM produces the highest efficiency with less phase current which reduces the converter burden. However, with asymmetric half bridge converter, eight power switches are required for 8/6 SRM and thus put a burden on the overall drive cost. As a solution, the Miller converter with only six switches for four phase SRM. To verify the proposed idea, the 8/6 SRM was manufactured and tested. The results show that Miller converter can be used for the proposed SRM with slightly reduced efficiency at 80.4%.

Selecting Sanitation Solutions for Peri-urban Areas: A Case Study of Can Tho, Vietnam

2010 ◽  
Vol 5 (4) ◽  
Author(s):  
Naomi Carrard ◽  
Juliet Willetts ◽  
Cynthia Mitchell ◽  
Mick Paddon ◽  
Monique Retamal
Keyword(s):  
Urban Areas ◽  
Cost Effective ◽  
Asset Replacement ◽  
Fit For Purpose ◽  
Infrastructure Investments ◽  
Sanitation Systems ◽  
Can Tho City ◽  
Sustainable Futures ◽  
Sanitation Infrastructure ◽  
Selection Of

In peri-urban areas where infrastructure investments have not yet been made, there is a need to determine the most context-appropriate, fit for purpose and sustainable sanitation solutions. Decision makers must identify the optimal system scale (on the spectrum from centralized to community to cluster scale) and assess the long-term costs and socio-economic/environmental impacts associated with different options. Addressing both cost-effectiveness and sustainability are essential to ensure that institutions and communities are able to continue to bear the costs and management burden of infrastructure operation, maintenance and asset replacement. This paper describes an approach to sanitation planning currently being undertaken as a research study in Can Tho City in southern Vietnam, by the Institute for Sustainable Futures and Can Tho University in collaboration with Can Tho Water Supply and Sewerage Company. The aim of the study is to facilitate selection of the most context-appropriate, fit for purpose, cost effective and sustainable sanitation infrastructure solution. As such, the study compares a range of sanitation alternatives including centralized, decentralized (at household or cluster scale) and resource recovery options. This paper provides an overview of the study and considers aspects of the Can Tho and Vietnamese regulatory, development and institutional context that present drivers and challenges for comparison of options and selection of fit for purpose sanitation systems.

Optimum Selection of Hydraulic Devices for Water Hammer Control in the Pipeline Systems Using Genetic Algorithm

2003 ◽  
Author(s):  
Bong Seong Jung ◽  
Bryan W. Karney
Keyword(s):  
Genetic Algorithm ◽  
Steady State ◽  
Optimization Problems ◽  
System Optimization ◽  
Water Hammer ◽  
Pipeline System ◽  
Optimal Size ◽  
Protection Strategy ◽  
Hydraulic Devices ◽  
Selection Of

Genetic algorithms have been used to solve many water distribution system optimization problems, but have generally been limited to steady state or quasi-steady state optimization. However, transient events within pipe system are inevitable and the effect of water hammer should not be overlooked. The purpose of this paper is to optimize the selection, sizing and placement of hydraulic devices in a pipeline system considering its transient response. A global optimal solution using genetic algorithm suggests optimal size, location and number of hydraulic devices to cope with water hammer. This study shows that the integration of a genetic algorithm code with a transient simulator can improve both the design and the response of a pipe network. This study also shows that the selection of optimum protection strategy is an integrated problem, involving consideration of loading condition, device and system characteristics, and protection strategy. Simpler transient control systems are often found to outperform more complex ones.

Sign in / Sign up

Export Citation Format

Share Document