scholarly journals Fuel Injector Testing Through Development of a New Test Rig

2019 ◽  
Vol 8 (9) ◽  
pp. 2904-2909
Keyword(s):  
Fuel Injection ◽  
Cylinder Liner ◽  
Heating System ◽  
Injection Rate ◽  
Engine Fuel ◽  
Exhaust Manifold ◽  
Fuel Injector ◽  
Test Rig ◽  
Recirculation System ◽  
Fuel Injection Rate

A modified version of fuel injector with higher injection capacity has been developed. To achieve this, the injector plunger diameter is increased to 11mm from current 9.5mm. A new test rig is developed to understand the functioning of the injector due to the changes incorporated. The new test rig is designed to test injector operation without burning the fuel. Since internal combustion is not present an external arrangement is required to run the engine. This is achieved through a 3-phase induction motor, which is coupled with the crankshaft of the engine. The injected fuel is collected form the cylinders and it is then recirculated. A fuel cooling circuit is also incorporated along with the fuel recirculation system to maintain the temperature of fuel at inlet of fuel pump. An oil heating system is installed in the test rig to maintain the viscosity of the oil by heating it. The required systems for driving the engine, fuel cooling and oil heating are implemented as per the design. The test is conducted on a 19 L diesel engine. Parts which are not required for this test like piston, piston rings, intake and exhaust manifold etc are removed from the engine. And the cylinder liner is blocked from below using a plate to facilitate the collection of injected fuel. Engine is made to run using the motoring rig at the rated speed of 1500 rpm for a duration of 250 hours. Instrumented push tubes are used to measure the push tube load. Push tube load is observed to be in the range of 2700 to 3100 lbf, which is high as compared to the earlier model of the injector. Fuel injection rate is obtained from the fuel collected from the cylinders. And the average fuel injection rate is observed as 0.116 to 2.35 kg/min. Thus, the increase in plunger diameter has led to an increase in fuel injection rate

Fuel Injector Design Based on 2D Technology

2012 ◽  
Vol 482-484 ◽  
pp. 1943-1946
Author(s):  
Li Dan Chen ◽  
Huang Xiang Shan
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Injection Rate ◽  
Injection System ◽  
Fuel Injector ◽  
Electromagnetic Valve ◽  
Spool Valve ◽  
Fuel Injection Rate ◽  
Injector Design ◽  
The Ideal

Through the discussion of main shortages of the high-speed electromagnetic valve used in electronic fuel injection system, the author introduced a new design thought of fuel injector based on 2D technology. Axial displacement of controlling valve was used to control the volume of gushing oil, while radial revolution of spool valve was used to change the time of injection. Additionally, mathematic modeling and MATLAB simulating indicated that, the injector designed based on 2D technology acquired the advantages of quick response and also realized the ideal shape of fuel injection rate.

Rate Shaping Estimation and Control of a Piezoelectric Fuel Injector

2013 ◽  
Author(s):  
Dat Le ◽  
Bradley W. Pietrzak ◽  
Gregory M. Shaver
Keyword(s):  
Fuel Injection ◽  
Fuel Efficiency ◽  
Nonlinear Behavior ◽  
Fast Response ◽  
Injection Rate ◽  
Fuel Injector ◽  
Fuel Injectors ◽  
Rate Shaping ◽  
Estimation And Control ◽  
Fuel Injection Rate

Fuel injection rate shaping is one way to improve fuel efficiency and reduce harmful emissions in IC engines. Piezoelectrically actuated fuel injectors have a particularly fast response, which makes them capable of rate shaping operation. In this paper, a model-based closed-loop controller is designed to control the fuel injection rate passing through the nozzle of a piezoelectric fuel injector, by compensating for the injector’s nonlinear behavior. The performance of this controller is verified with simulation results.

scholarly journals A Study of Combustion Characteristics of Two Gasoline–Biodiesel Mixtures on RCEM Using Various Fuel Injection Pressures

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3265
Author(s):  
Ardhika Setiawan ◽  
Bambang Wahono ◽  
Ocktaeck Lim
Keyword(s):  
Heat Release ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Fuel Mixture ◽  
Injection Rate ◽  
Injection Duration ◽  
Late Start ◽  
Fuel Injection Rate ◽  
Injection Pressures

Experimental research was conducted on a rapid compression and expansion machine (RCEM) that has characteristics similar to a gasoline compression ignition (GCI) engine, using two gasoline–biodiesel (GB) blends—10% and 20% volume—with fuel injection pressures varying from 800 to 1400 bar. Biodiesel content lower than GB10 will result in misfires at fuel injection pressures of 800 bar and 1000 bar due to long ignition delays; this is why GB10 was the lowest biodiesel blend used in this experiment. The engine compression ratio was set at 16, with 1000 µs of injection duration and 12.5 degree before top dead center (BTDC). The results show that the GB20 had a shorter ignition delay than the GB10, and that increasing the injection pressure expedited the autoignition. The rate of heat release for both fuel mixes increased with increasing fuel injection pressure, although there was a degradation of heat release rate for the GB20 at the 1400-bar fuel injection rate due to retarded in-cylinder peak pressure at 0.24 degree BTDC. As the ignition delay decreased, the brake thermal efficiency (BTE) decreased and the fuel consumption increased due to the lack of air–fuel mixture homogeneity caused by the short ignition delay. At the fuel injection rate of 800 bar, the GB10 showed the worst efficiency due to the late start of combustion at 3.5 degree after top dead center (ATDC).

Suppression of Instabilities in Gaseous Fuel High-Pressure Combustor Using Non-Coherent Oscillatory Fuel Injection

2003 ◽  
Author(s):  
D. Shcherbik ◽  
E. Lubarsky ◽  
Y. Neumeier ◽  
B. T. Zinn ◽  
K. McManus ◽  
...  
Keyword(s):  
High Pressure ◽  
Active Control ◽  
Fuel Injection ◽  
Injection Rate ◽  
Open Loop ◽  
Combustion Instabilities ◽  
Open Loop Control ◽  
Pressure Oscillations ◽  
Loop Control ◽  
Fuel Injection Rate

This paper describes the application of active, open loop, control in effective damping of severe combustion instabilities in a high pressure (i.e., around 520 psi) gas turbine combustor simulator. Active control was applied by harmonic modulation of the fuel injection rate into the combustor. The open-loop active control system consisted of a pressure sensor and a fast response actuating valve. To determine the dependence of the performance of the active control system upon the frequency, the fuel injection modulation frequency was varied between 300 and 420 Hz while the frequency of instability was around 375 Hz. These tests showed that the amplitude of the combustor pressure oscillations strongly depended upon the frequency of the open loop control. In fact, the amplitude of the combustor pressure oscillations varied ten fold over the range of investigated frequencies, indicating that applying the investigated open loop control approach at the appropriate frequency could effectively damp detrimental combustion instabilities. This was confirmed in subsequent tests in which initiation of open loop modulation of the fuel injection rate at a non resonant frequency of 300Hz during unstable operation with peak to peak instability amplitude of 114 psi and a frequency of 375Hz suppressed the instability to a level of 12 psi within approximately 0.2 sec (i.e., 75 periods). Analysis of the time dependence of the spectra of the pressure oscillations during suppression of the instability strongly suggested that the open loop fuel injection rate modulation effectively damped the instability by “breaking up” (or preventing the establishment of) the feedback loop between the reaction rate and combustor oscillations that drove the instability.

Sign in / Sign up

Export Citation Format

Share Document