scholarly journals Numerical Analysis of Innovative Wind Booster Configurations for Vertical Axis Wind Turbines

2020 ◽  
Vol 9 (1) ◽  
pp. 744-746
Keyword(s):  
Numerical Analysis ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Two Stage ◽  
Vertical Axis Wind Turbines ◽  
Magnitude Range ◽  
Velocity Pressure ◽  
Domestic Level ◽  
Pressure Magnitude

Vertical Axis Wind Turbines has been looked upon by researchers as a potential avenue for power generation at domestic level. The Coefficient of Power of Vertical Axis wind Turbine has its limitations mentioned by Betz theory. In this paper three configurations viz one stage, two stage and three stage Wind booster has been designed, modelled and numerically analyzed. A Multistage concept of flaps has been used in wind booster so that wind velocity may increase during each stage. The performance of turbine is assessed by wind booster for Flow velocity, Pressure. For Numerical analysis SST K-epsilon turbulence model has been used. From the analysis it is found that, the two stage wind booster velocity and pressure magnitude range is superior as compared to other two configurations.

Vertical axis wind turbine operation in icing conditions: A review study

2021 ◽  
pp. 0309524X2110618
Author(s):  
Syed Abdur Rahman Tahir ◽  
Muhammad Shakeel Virk
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Electricity Production ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Horizontal Axis Wind Turbines ◽  
Promising Solution ◽  
Review Study ◽  
Accretion Physics

Vertical Axis Wind Turbine (VAWT) can be a promising solution for electricity production in remote ice prone territories of high north, where good wind resources are available, but icing is a challenge that can affect its optimum operation. A lot of research has been made to study the icing effects on the conventional horizontal axis wind turbines, but the literature about vertical axis wind turbines operating in icing conditions is still scarce, despite the importance of this topic. This paper presents a review study about existing knowledge of VAWT operation in icing condition. Focus has been made in better understanding of ice accretion physics along VAWT blades and methods to detect and mitigate icing effects.

scholarly journals Aerodynamic improvement of Darrieus wind turbine

2021 ◽  
Vol 897 (1) ◽  
pp. 012001
Author(s):  
Oleg Goman ◽  
Andrii Dreus ◽  
Anton Rozhkevych ◽  
Krystyna Heti
Keyword(s):  
Reynolds Number ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Reliability ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Integral Approach ◽  
Vertical Axis Wind Turbine ◽  
Calculation Algorithm ◽  
Vertical Axis Wind Turbines

Abstract Until recently, vertical-axis wind turbines are less extensively developed in wind energetics. At the same time, there are a number of advantages in turbines of such type like their independence from the change of wind direction, lower levels of aerodynamic and infrasound noises, higher structural reliability (compared to horizontal engines), etc. With these advantages, vertical-axis wind turbines demonstrate promising capacities. Inter alia, the productiveness of such turbines can be refined through the aerodynamic improvement of the structure and comprehensive optimization of the rotor geometry. The main purpose of the presented paper is to aerodynamically improve vertical wind turbine in order to increase the efficiency of wind energy conversion into electricity. Within the framework of the classical theory of impulses, this article presents a study of the effect of variation in Reynolds number on the general energy characteristics of a vertical-axis wind turbine with two blades. The integral approach makes it possible to use a single-disk impulse model to determine the main specific indicators of the system. The power factor was calculated based on the obtained value of the shaft torque factor, which in turn was determined by numerically integrating the total torque generated by the wind turbine. To calculate the test problem, we used the classic NACA airfoils: 0012, 0015, 0018 and 0021. The proposed calculation algorithm makes it possible not to indicate the Reynolds number and corresponding aerodynamic coefficients at the beginning of the calculation, but to recalculate it depending on the relative speed, position of the airfoil and the linear speed of the airfoil around the circumference. Proposed modern design techniques can be helpful for optimization of vertical wind turbines.

Investigation of vertical axis wind turbine airfoil performance in rain

2017 ◽  
Vol 232 (2) ◽  
pp. 181-194 ◽  
Author(s):  
Zhenlong Wu ◽  
Yihua Cao
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Meteorological Condition ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Turbine Performance ◽  
Practical Design ◽  
Wind Turbine Airfoil ◽  
Naca 0015

Rainfall is a common meteorological condition that wind turbines may encounter and by which their performance may be affected. This paper comprehensively investigates the effects of rainfall on a NACA 0015 airfoil which is commonly used in vertical axis wind turbines. A CFD-based Eulerian–Lagrangian multiphase approach is proposed to study the static, rotating, and oscillating performances of the NACA 0015 airfoil in rainy conditions. It is found that for the different airfoil movements, the airfoil performance can seriously be deteriorated in the rain condition. Rain also causes premature boundary layer separations and more severe flow recirculations than in the dry condition. These findings seem to be the first open reports on rain effects on wind turbine performance and should be of some significance to practical design.

scholarly journals On mooring line tension and fatigue prediction for offshore vertical axis wind turbines: A comparison of lumped mass and quasi-static approaches

2018 ◽  
Vol 42 (2) ◽  
pp. 97-107 ◽  
Author(s):  
D Cevasco ◽  
M Collu ◽  
CM Rizzo ◽  
M Hall
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Line Tension ◽  
Vertical Axis ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Vertical Axis Wind Turbine ◽  
Lumped Mass ◽  
Vertical Axis Wind Turbines

Despite several potential advantages, relatively few studies and design support tools have been developed for floating vertical axis wind turbines. Due to the substantial aerodynamics differences, the analyses of vertical axis wind turbine on floating structures cannot be easily extended from what have been already done for horizontal axis wind turbines. Therefore, the main aim of the present work is to compare the dynamic response of the floating offshore wind turbine system adopting two different mooring dynamics approaches. Two versions of the in-house aero-hydro-mooring coupled model of dynamics for floating vertical axis wind turbine (FloVAWT) have been used, employing a mooring quasi-static model, which solves the equations using an energetic approach, and a modified version of floating vertical axis wind turbine, which instead couples with the lumped mass mooring line model MoorDyn. The results, in terms of mooring line tension, fatigue and response in frequency have been obtained and analysed, based on a 5 MW Darrieus type rotor supported by the OC4-DeepCwind semisubmersible.

scholarly journals An experimental study of the optimal design parameters of a wind power tower used to improve the performance of vertical axis wind turbines

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879954
Author(s):  
Soo-Yong Cho ◽  
Sang-Kyu Choi ◽  
Jin-Gyun Kim ◽  
Chong-Hyun Cho
Keyword(s):  
Experimental Study ◽  
Optimal Design ◽  
Wind Turbine ◽  
Wind Power ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

In order to augment the performance of vertical axis wind turbines, wind power towers have been used because they increase the frontal area. Typically, the wind power tower is installed as a circular column around a vertical axis wind turbine because the vertical axis wind turbine should be operated in an omnidirectional wind. As a result, the performance of the vertical axis wind turbine depends on the design parameters of the wind power tower. An experimental study was conducted in a wind tunnel to investigate the optimal design parameters of the wind power tower. Three different sizes of guide walls were applied to test with various wind power tower design parameters. The tested vertical axis wind turbine consisted of three blades of the NACA0018 profile and its solidity was 0.5. In order to simulate the operation in omnidirectional winds, the wind power tower was fabricated to be rotated. The performance of the vertical axis wind turbine was severely varied depending on the azimuthal location of the wind power tower. Comparison of the performance of the vertical axis wind turbine was performed based on the power coefficient obtained by averaging for the one periodic azimuth angle. The optimal design parameters were estimated using the results obtained under equal experimental conditions. When the non-dimensional inner gap was 0.3, the performance of the vertical axis wind turbine was better than any other gaps.

FloVAWT: Progress on the Development of a Coupled Model of Dynamics for Floating Offshore Vertical Axis Wind Turbines

2013 ◽  
Author(s):  
Maurizio Collu ◽  
Michael Borg ◽  
Andrew Shires ◽  
Feargal P. Brennan
Keyword(s):  
Experimental Data ◽  
Wind Turbines ◽  
Three Dimensional ◽  
Coupled Model ◽  
Vertical Axis ◽  
Potential Method ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Wind Profiles ◽  
Gyroscopic Effects

In the present article, progress on the development of an aero-hydro-servo-elastic coupled model of dynamics for floating Vertical Axis Wind Turbines (VAWTs) is presented, called FloVAWT (Floating Vertical Axis Wind Turbine). Aerodynamics is based on Paraschivoiu’s Double-Multiple Streamtube (DMST) model [1] [2], relying on blade element momentum (BEM) theory, but also taking into account three-dimensional effects, dynamic stall, and unsteady wind profiles and platform motions. Hydrodynamics is modelled with a time domain seakeeping model [3], based on hydrodynamic coefficients estimated with a frequency analysis potential method. In this first phase of the research program, the system is considered a rigid body. The mooring system is represented through a user defined force-displacement relationship. Due to the lack of experimental data on offshore floating VAWTs, the model has initially been validated by taking each module separately and comparing it against known experimental data, showing good agreement. The capabilities of the program are illustrated through a case study, giving an insight on the relative importance of aerodynamics loads and gyroscopic effects with respect to hydrodynamic load effects.

Investigation of Self-Starting Capability of Vertical Axis Wind Turbines Using a Computational Fluid Dynamics Approach

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Alexandrina Untaroiu ◽  
Houston G. Wood ◽  
Paul E. Allaire ◽  
Robert J. Ribando
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Mesh Deformation ◽  
Operating Speed ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Turbine Performance

Vertical axis wind turbines have always been a controversial technology; claims regarding their benefits and drawbacks have been debated since the initial patent in 1931. Despite this contention, very little systematic vertical axis wind turbine research has been accomplished. Experimental assessments remain prohibitively expensive, while analytical analyses are limited by the complexity of the system. Numerical methods can address both concerns, but inadequate computing power hampered this field. Instead, approximating models were developed which provided some basis for study; but all these exhibited high error margins when compared with actual turbine performance data and were only useful in some operating regimes. Modern computers are capable of more accurate computational fluid dynamics analysis, but most research has focused on horizontal axis configurations or modeling of single blades rather than full geometries. In order to address this research gap, a systematic review of vertical axis wind-power turbine (VAWT) was undertaken, starting with establishment of a methodology for vertical axis wind turbine simulation that is presented in this paper. Replicating the experimental prototype, both 2D and 3D models of a three-bladed vertical axis wind turbine were generated. Full transient computational fluid dynamics (CFD) simulations using mesh deformation capability available in ansys-CFX were run from turbine start-up to operating speed and compared with the experimental data in order to validate the technique. A circular inner domain, containing the blades and the rotor, was allowed to undergo mesh deformation with a rotational velocity that varied with torque generated by the incoming wind. Results have demonstrated that a transient CFD simulation using a two-dimensional computational model can accurately predict vertical axis wind turbine operating speed within 12% error, with the caveat that intermediate turbine performance is not accurately captured.

Numerical analysis of the one-stage and two-stage helical Savonius vertical axis wind turbine

2022 ◽  
Author(s):  
S. Seralathan ◽  
P. S. Dinesh Kumar ◽  
Subham Singh ◽  
Rabin Raj ◽  
S. Sathish
Keyword(s):  
Numerical Analysis ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Two Stage ◽  
One Stage ◽  
The One

1422 Numerical analysis of vertical axis wind turbines under various design conditions

2010 ◽  
Vol 2010 (0) ◽  
pp. 433-434
Author(s):  
Junsuke MURATA ◽  
Yasunari KAMADA ◽  
Takao MAEDA ◽  
Yuya HIROMORI ◽  
Tomofumi KAWAI ◽  
...  
Keyword(s):  
Numerical Analysis ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbines

Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel

2010 ◽  
Author(s):  
L. Battisti ◽  
L. Zanne ◽  
S. Dell’Anna ◽  
V. Dossena ◽  
B. Paradiso ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Optimization ◽  
Vertical Axis Wind Turbines

This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular attention, as interesting alternative for small and micro generation applications. However, the complex fluid dynamic mechanisms occurring in these machines make the aerodynamic optimization of the rotors still an open issue and detailed experimental analyses are now highly recommended to convert improved flow field comprehensions into novel design techniques. The experiments were performed in the large-scale wind tunnel of the Politecnico di Milano (Italy), where real-scale wind turbines for micro generation can be tested in full similarity conditions. Open and closed wind tunnel configurations are considered in such a way to quantify the influence of model blockage for several operational conditions. Integral torque and thrust measurements, as well as detailed aerodynamic measurements were applied to characterize the 3D flow field downstream of the turbine. The local unsteady flow field and the streamwise turbulent component, both resolved in phase with the rotor position, were derived by hot wire measurements. The paper critically analyses the models and the correlations usually applied to correct the wind tunnel blockage effects. Results evidence that the presently available theoretical correction models does not provide accurate estimates of the blockage effect in the case of vertical axis wind turbines. The tip aerodynamic phenomena, in particular, seem to play a key role for the prediction of the turbine performance; large-scale unsteadiness is observed in that region and a simple flow model is used to explain the different flow features with respect to horizontal axis wind turbines.

Sign in / Sign up

Export Citation Format

Share Document