scholarly journals Slope Stability Evaluation of Geosynthetic Reinforced Soil

2019 ◽  
Vol 8 (4) ◽  
pp. 7143-7147
Keyword(s):  
Slope Stability ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Friction Angle ◽  
Calculation Model ◽  
Reinforced Soil ◽  
Unit Weight ◽  
Soil Parameters

The slippery of natural slope is sometimes ruled by combination of soil parameters and earthquake characteristics. Geotextiles could be a reinforcing materials and an application in numerous areas still as in geotechnical application to supply additional lateral restraint and forestall the high rise hill from failure. The analysis was aimed to analyze slope stability analysis, strengthened the Finite slope with non-woven geotextiles. The modal of hill was created within the SLOPE/W software system of GeoStudio that is predicated on limit equilibrium of slope analysis. The results of issue of safety square measure compared while not and with use of geotextiles in several layers. The issue of safety of slope failure will increase from three.437M to 9.978M victimization 3 layers of geotextiles at optimum height. Thus, this study confirms that the non-woven geotextiles may be applied in slope so as to enhance the soundness of natural or mam-made slope. During this regard, special stress is given to the sensitivity of the Calculation model input parameters like friction angle, cohesion, Pore water pressure and unit weight of soil that ought to contribute to raising awareness regarding these problems, as a requirement to create the proper selections and optimum technical resolution during this space.

scholarly journals The Hydromechanical Interplay in the Simplified Three-Dimensional Limit Equilibrium Analyses of Unsaturated Slope Stability

Geosciences ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 73
Author(s):  
Panagiotis Sitarenios ◽  
Francesca Casini
Keyword(s):  
Analytical Solution ◽  
Slope Stability ◽  
Slope Failure ◽  
Failure Modes ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Three Dimensional ◽  
Stability Limit ◽  
Smooth Transition

This paper presents a three-dimensional slope stability limit equilibrium solution for translational planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr–Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment. The comparison suggests that, despite its relative simplicity, the analytical solution can capture the experimentally observed behaviour well and highlights the importance of considering lateral resistance together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

scholarly journals The Hydromechanical Interplay in the Three-dimensional Limit Equilibrium Analyses of Unsaturated Slope Stability

2021 ◽  
Author(s):  
Panagiotis Sitarenios ◽  
Francesca Casini
Keyword(s):  
Analytical Solution ◽  
Slope Stability ◽  
Slope Failure ◽  
Failure Modes ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Three Dimensional ◽  
Stability Limit ◽  
Smooth Transition

The paper presents a three-dimensional slope stability limit equilibrium solution for translational, planar failure modes. The proposed solution uses Bishop’s average skeleton stress combined with the Mohr – Coulomb failure criterion to describe soil strength evolution under unsaturated conditions while its formulation ensures a natural and smooth transition from the unsaturated to the saturated regime and vice versa. The proposed analytical solution is evaluated by comparing its predictions with the results of the Ruedlingen slope failure experiment [1]. The comparison suggests that despite its relative simplicity the analytical solution can capture well the experimentally observed behaviour and highlights the importance of lateral resistance consideration together with a realistic interplay between mechanical parameters (cohesion) and hydraulic (pore water pressure) conditions.

Analyses for the stability of potash tailings piles

1993 ◽  
Vol 30 (3) ◽  
pp. 491-505 ◽  
Author(s):  
Delwyn G. Fredlund ◽  
Zai Ming Zhang ◽  
Karen Macdonald
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Field Studies ◽  
Equilibrium Analysis ◽  
Limit Equilibrium Analysis ◽  
Dissipation Model ◽  
The Stability

The stability of potash tailings piles is investigated using a pore-water pressure generation and dissipation model together with a limit equilibrium analysis. It is found that a shallow toe failure mode is generally the most applicable and that the stability may be influenced by pore-water pressure migration below the pile. It is suggested that field studies would be useful in evaluating stability in the toe region of the pile. Key words : potash tailings, slope stability, pore pressure dissipation, solutioning.

Influence of cross correlation between soil parameters on probability of failure of simple cohesive and c-ϕ slopes

2016 ◽  
Vol 53 (5) ◽  
pp. 839-853 ◽  
Author(s):  
Sina Javankhoshdel ◽  
Richard J. Bathurst
Keyword(s):  
Slope Stability ◽  
Soil Properties ◽  
Cross Correlation ◽  
Friction Angle ◽  
Probability Of Failure ◽  
Unit Weight ◽  
Soil Parameters ◽  
Design Charts ◽  
Soil Slopes ◽  
Cross Correlations

This paper focuses on the calculation of probability of failure of simple unreinforced slopes and the influence of the magnitude of cross correlation between soil parameters on numerical outcomes. A general closed-form solution for cohesive slopes with cross correlation between cohesion and unit weight was investigated and results compared with cases without cross correlation. Negative cross correlations between cohesion and friction angle and positive cross correlations between cohesion and unit weight, and friction angle and unit weight were considered in the current study. The factors of safety and probabilities of failure for the slopes with uncorrelated soil properties were obtained using probabilistic slope stability design charts previously reported by the writers. Results for cohesive soil slopes and positive cross correlation between cohesion and unit weight are shown to decrease probability of failure. Probability of failure also decreased for increasing negative cross correlation between cohesion and friction angle, and increasing positive correlation between cohesion and unit weight, and friction angle and unit weight. Probabilistic slope stability design charts presented by the writers in an earlier publication are extended to include cohesive-frictional (c-[Formula: see text]) soil slopes with and without cross correlation between soil input parameters. An important outcome of the work presented here is that cross correlation between random values of soil properties can reduce the probability of failure for simple slope cases. Hence, previous probabilistic design charts by the writers for simple soil slopes with uncorrelated soil properties are conservative (safe) for design. This study also provides one explanation why slope stability analyses using uncorrelated soil properties can predict unreasonably high probabilities of failure when conventional estimates of factor of safety suggest a stable slope.

scholarly journals Analysis of shallow failures triggered by the 14-16 November 2002 event in the Albaredo valley, Valtellina (Northern Italy)

2005 ◽  
Vol 2 ◽  
pp. 305-308 ◽  
Author(s):  
S. Dapporto ◽  
P. Aleotti ◽  
N. Casagli ◽  
G. Polloni
Keyword(s):  
Pore Water ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Coupled Analysis ◽  
Element Analysis ◽  
Seepage Analysis ◽  
The North ◽  
Pressure Distributions

Abstract. On 14-16 November 2002 the North Italy was affected by an intense rainfall event: in the Albaredo valley (Valtellina) more than 200 mm of rain fell triggering about 50 shallow landslides, mainly soil slips and soil slip-debris flows. Landslides occurred above the critical rainfall thresholds computed by Cancelli and Nova (1985) and Ceriani et al. (1994) for the Italian Central Alps: in fact the cumulative precipitation at the soil slips initiation time was 230 mm (in two days) with a peak intensity of 15 mm/h. A coupled analysis of seepage and instability mechanisms is performed in order to evaluate the potential for slope failure during the event. Changes in positive and negative pore water pressures during the event are modelled by a finite element analysis of water flow in transient conditions, using as boundary condition for the nodes along the slope surface the recorded rainfall rate. The slope stability analysis is conducted applying the limit equilibrium method, using pore water pressure distributions obtained in the different time steps by the seepage analysis as input data for the calculation of the factor of safety.

Slope stability study of the 2001 Taipei National University of the Arts landslide

2020 ◽  
Author(s):  
Chien Liu ◽  
Cheng-Han Lin ◽  
Ching Hung
Keyword(s):  
Slope Stability ◽  
Junior High School ◽  
Factor Of Safety ◽  
Slope Failure ◽  
Limit Equilibrium ◽  
Equilibrium Analysis ◽  
Soil Parameters ◽  
Element Analysis ◽  
The Arts ◽  
National University

<p>Situated within a subtropical and mountainous region where frequent typhoons hit, rainfall-induced landslides have been a critical issue in Taiwan. On September 29, 2001, due to the torrential rainfall brought by the Typhoon Nari and Lekima, a downslope in Taipei National University of the Arts failed. The sliding source hit and severely damaged the Tao-Yuan junior high school. Before the 2001 Taipei National University of the Arts landslide, several landslides had already occurred in this landslide-prone region. In this study, a two-dimensional (2D) slope stability analysis, based on the limit equilibrium analysis (LEA), is conducted to analyze the 2001 Taipei National University of the Arts landslide. LEA has been the most popular and widely used technique given that it can estimate the factor of safety of a slope with some preliminary site investigation information. By comparing the failure surface and factor of safety (FOS) suggested in the post-disaster report [1], reasonable soil parameters, which are in an agreement with the experimental results [1], can be obtained through the study. The obtained soil parameters can later be applied to coupled transient unsaturated seepage-stress finite element analysis (FEA) [2] that will help practical engineers to understand the onset of failure in the future study.</p><p> </p><p>REFERENCE</p><ol><li>Taiwan Professional Geotechnical Engineers Association. (2001). National Taipei University of the Arts tennis court down slope failure reason identification and long-term remediation plan suggestion work report.</li> <li>Hung, C., Liu, C. H., & Chang, C. M. (2018). Numerical investigation of rainfall-induced landslide in mudstone using coupled finite and discrete element analysis. Geofluids, 2018.</li> </ol>

The Effect of Rainfall Infiltration Time to the Unsaturated Soil Slope Stability

2011 ◽  
Vol 71-78 ◽  
pp. 4864-4867
Author(s):  
Guang Hua Cai ◽  
Hai Jun Lu ◽  
Wei He ◽  
Long Guan ◽  
Wei Qi Xu
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Rainfall Infiltration ◽  
Soil Slope ◽  
Soil Permeability ◽  
Rainfall Condition ◽  
Pressure Changes

Rainfall infiltration is currently one of the important factors in studying the soil-slope stability. By using saturated-unsaturated seepage theory, the traditional limit equilibrium method and so on, analyze the water content and the pore-water pressure changes under the rainfall condition, then analyze the influence mechanism of the slope stability. Through the Seep/W and the Slope/W of the GEO-Slope software, do the numerical simulation of the slope stability under the rainfall condition, to seek the distribution of pore-water pressure on the rainfall situation and the influence of the seepage field from various parameters such as rainfall intensity and the soil permeability coefficient, thus to study the slope stability.

scholarly journals Unsaturated seepage and stability of double-layer slope under rainfall infiltration

2021 ◽  
Vol 248 ◽  
pp. 03024
Author(s):  
Yuan Zhang ◽  
Haifeng Lu
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Safety Factor ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Parameters ◽  
Lag Period ◽  
Rainfall Patterns ◽  
Continuous Rainfall ◽  
Slope Safety

Taking a homogeneous double-layer soil slope as an example, the SEEP/W module and SLOPE/W module in the finite element analysis software GeoStudio were used in this paper. Then, the changes of pore water pressure and stability under different rainfall patterns and soil parameters were studied. Finally, the variation curves of pore water pressure and slope safety factor with rainfall time were obtained. The results show that: Soil parameters a and m are directly proportional to the slope safety factor, while n is inversely proportional to the slope safety factor. Under the condition of continuous rainfall, the decreasing rate of slope safety factor is directly proportional to the rainfall intensity.Under different rainfall patterns, the continuous rainfall in the advanced and normal rainfall patterns will cause the slope stability to decline and then gradually recover, while delayed and averaged rainfall patterns rainfall will cause the slope stability to decline continuously.In addition, there is a lag period in the change of slope safety factor, and the whole lag period lasts about 6 hours. During the lag period, the pore water pressure inside the soil began to decrease, while the slope safety factor continued to decrease. The safety factor starts to recover after the lag period ends.

scholarly journals Behavior analysis by model slope experiment of artificial rainfall

2015 ◽  
Vol 3 (6) ◽  
pp. 4159-4187
Author(s):  
M. C. Park
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Pore Water ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Matric Suction ◽  
Slope Stability Analysis ◽  
Model Slope ◽  
Rainfall Seepage

Abstract. In this study, we performed a model slope experiment with rainfall seepage, and the results were compared and verified with the unsaturated slope stability analysis method. In the model slope experiment, we measured the changes in water content and matric suction due to rainfall seepage, and determined the time at which the slope failure occurred and the shape of the failure. In addition, we compared and verified the changes in the factor of safety and the shape of the failure surface, which was calculated from the unsaturated slope stability analysis with the model experiment. From the results of experiment and analysis, it is concluded that the unsaturated slope stability analysis can be used to accurately analyze and predict rainfall-induced slope failure. It is also concluded that in seepage analysis, setting the initial conditions and boundary conditions is very important. If engineers will use the measured pore water pressure or matric suction, the accuracy of analysis can be enhanced. The real-time monitoring system of pore water pressure or matric suction can be used as a warning of rainfall-induced slope failure.

scholarly journals Emulating computer experiments of transport infrastructure slope stability using Gaussian processes and Bayesian inference

2021 ◽  
Vol 2 ◽  
Author(s):  
Aleksandra Svalova ◽  
Peter Helm ◽  
Dennis Prangle ◽  
Mohamed Rouainia ◽  
Stephanie Glendinning ◽  
...  
Keyword(s):  
Bayesian Inference ◽  
Slope Stability ◽  
Pore Water ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Computer Experiments ◽  
Transport Infrastructure ◽  
High Plasticity ◽  
Increased Risk

Abstract We propose using fully Bayesian Gaussian process emulation (GPE) as a surrogate for expensive computer experiments of transport infrastructure cut slopes in high-plasticity clay soils that are associated with an increased risk of failure. Our deterioration experiments simulate the dissipation of excess pore water pressure and seasonal pore water pressure cycles to determine slope failure time. It is impractical to perform the number of computer simulations that would be sufficient to make slope stability predictions over a meaningful range of geometries and strength parameters. Therefore, a GPE is used as an interpolator over a set of optimally spaced simulator runs modeling the time to slope failure as a function of geometry, strength, and permeability. Bayesian inference and Markov chain Monte Carlo simulation are used to obtain posterior estimates of the GPE parameters. For the experiments that do not reach failure within model time of 184 years, the time to failure is stochastically imputed by the Bayesian model. The trained GPE has the potential to inform infrastructure slope design, management, and maintenance. The reduction in computational cost compared with the original simulator makes it a highly attractive tool which can be applied to the different spatio-temporal scales of transport networks.

Sign in / Sign up

Export Citation Format

Share Document