scholarly journals Strength and liquefaction assessment of tailings

Author(s):  
Mark Dillon ◽  
H Wardlaw
2020 ◽  
Vol 156 ◽  
pp. 02010
Author(s):  
Yusa Muhamad ◽  
Bowman Elisabeth T. ◽  
Nugroho S.A

National Disaster Management Agency (BNPB) statistics show that the majority of earthquake affected buildings are residential houses, whereas in practice, soil investigation is rarely conducted for residential houses in Indonesia. This study is preliminary work on the prospective of Swedish Weight Sounding (SWST) for liquefaction assessment for residential houses. Material used is poorly graded sand. The number of half turns from SWST (NSW) per meter for very loose and loose clean fine sand ranges from 4 to 168 (equivalent to SPT 0-30). Liquefaction potential was assessed using an indirect method by converting NSW into equivalent NSPT and direct method. In general, the factor of safety obtained from the direct method is more conservative (thus giving lower liquefaction potential index) than the indirect method. Torque measured for material in this study ranged from 6-54 Nm, equivalent to a specific energy range from 7-70 N/mm2. Liquefaction assessment using SWST data with torque measurement also indicated the soil is liquefiable. SWST also may be able to detect sand ageing. In summary SWS has a good prospect as a highly portable and low cost investigation tool for liquefaction assessment of residential houses in Indonesia.


2017 ◽  
Vol 17 (5) ◽  
pp. 781-800 ◽  
Author(s):  
Indranil Kongar ◽  
Tiziana Rossetto ◽  
Sonia Giovinazzi

Abstract. Currently, some catastrophe models used by the insurance industry account for liquefaction by applying a simple factor to shaking-induced losses. The factor is based only on local liquefaction susceptibility and this highlights the need for a more sophisticated approach to incorporating the effects of liquefaction in loss models. This study compares 11 unique models, each based on one of three principal simplified liquefaction assessment methods: liquefaction potential index (LPI) calculated from shear-wave velocity, the HAZUS software method and a method created specifically to make use of USGS remote sensing data. Data from the September 2010 Darfield and February 2011 Christchurch earthquakes in New Zealand are used to compare observed liquefaction occurrences to forecasts from these models using binary classification performance measures. The analysis shows that the best-performing model is the LPI calculated using known shear-wave velocity profiles, which correctly forecasts 78 % of sites where liquefaction occurred and 80 % of sites where liquefaction did not occur, when the threshold is set at 7. However, these data may not always be available to insurers. The next best model is also based on LPI but uses shear-wave velocity profiles simulated from the combination of USGS VS30 data and empirical functions that relate VS30 to average shear-wave velocities at shallower depths. This model correctly forecasts 58 % of sites where liquefaction occurred and 84 % of sites where liquefaction did not occur, when the threshold is set at 4. These scores increase to 78 and 86 %, respectively, when forecasts are based on liquefaction probabilities that are empirically related to the same values of LPI. This model is potentially more useful for insurance since the input data are publicly available. HAZUS models, which are commonly used in studies where no local model is available, perform poorly and incorrectly forecast 87 % of sites where liquefaction occurred, even at optimal thresholds. This paper also considers two models (HAZUS and EPOLLS) for estimation of the scale of liquefaction in terms of permanent ground deformation but finds that both models perform poorly, with correlations between observations and forecasts lower than 0.4 in all cases. Therefore these models potentially provide negligible additional value to loss estimation analysis outside of the regions for which they have been developed.


1994 ◽  
Vol 31 (6) ◽  
pp. 918-918
Author(s):  
Alan S. Imrie

This overview introduces a series of six papers describing the approach taken in a recent dam safety study to evaluate the liquefaction potential and deformation behaviour for the current seismic setting of Duncan Dam. The dam was originally designed and built in the mid-1960s and is an embankment structure founded on a thick sequence of glacial sediments. The papers were initially presented by a team of B.C. Hydro and their consultants at a specialty session held at the 46th Annual Canadian Conference in Saskatoon in September 1993. The papers provide an excellent summary of the current state of practice in evaluating liquefaction and post-liquefaction behaviour. Key words : embankment, liquefaction, seismic, specialty session.


2014 ◽  
Vol 30 (1) ◽  
pp. 111-129 ◽  
Author(s):  
Liam M. Wotherspoon ◽  
Rolando P. Orense ◽  
Mike Jacka ◽  
Russell A. Green ◽  
Brady R. Cox ◽  
...  

The city of Christchurch and the surrounding region on the South Island of New Zealand are underlain by large areas of recent alluvial sediments and fills that are highly susceptible to liquefaction and seismic ground failure. Thus, the widespread liquefaction that occurred following the successive large-scale earth-quakes, with moment magnitudes (MW) ranging from 6.0 to 7.1 that struck the Canterbury region in 2010–2011 was expected. Prior to the series of earthquakes, soil improvement had been used at several sites to mitigate the anticipated damage. This paper reviews the performance of improved sites during the Canterbury earthquake sequence. The existing soil conditions at each site and the design of the ground improvement are discussed, together with descriptions of the post-earthquake damage observed. Moreover, liquefaction assessment within and surrounding a selection of the ground improvement zones is presented.


Sign in / Sign up

Export Citation Format

Share Document