scholarly journals Effect of Aluminium Oxide Nano Additive on Diesel along with Gasoline Fumigation in Single Cylinder Diesel Engine

2021 ◽  
Author(s):  
Tamilvanan A ◽  
◽  
Bharathiraja M ◽  
Balamurugan K ◽  
Sasikumar C ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Dosage Level ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Nano Additives ◽  
Hc Emissions ◽  
Gasoline Fumigation ◽  
Working Parameters

The present investigation mainly focuses on overcoming the limitations of gasoline fumigation (GF) in diesel engines by adding up nano fuel additives. Experiments are conducted to ascertain the engine working characteristics in a single-cylinder, four-stroke diesel engine using aluminum oxide (Al2O3) nano additives blended diesel as the main injection fuel along with GF as an inducted fuel. GF was achieved by controlling the electronic injector fitted at the intake manifold using open ECU software. Fuel map for GF was determined based on experiments with three divergent fumigation rates of 10%, 20%, and 30% based on energy consumption and optimized using the design of experiments. The optimization results showed 10% fumigation resulted in better performance and emission characteristics and it is selected for this present investigation. Fumigation results showed a decrease in brake thermal efficiency (BTE) at low and medium loads; increase at high loads.The two different mass fractions of 25 ppm and 50 ppm Al2O3 nano liquid are blended with diesel. Compared to GF with diesel, GF along with 25 and 50ppm Al2O3 nano additives blended diesel showed an increased BTE, maximum in-cylinder pressure, cumulative heat release rate; and reduced smoke opacity, CO, and unburned HC emissions at overall operating conditions. As the dosage level of Al2O3 increases from 25 to 50 ppm results in further enhancement of all working parameters except NOx emission. Finally, the addition of an Al2O3 nano additive is a suitable solution to overcome the limitations of GF in the CI engine.

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

Performance and emission study of a single cylinder diesel engine fuelled with n-octanol/WPO with some modifications

2018 ◽  
pp. 1-10 ◽  
Author(s):  
D. Damodharan ◽  
K. Gopal ◽  
A. P. Sathiyagnanam ◽  
B. Rajesh Kumar ◽  
Melvin Victor Depoures ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Emission Study

Simulation of a Single Cylinder Diesel Engine Under Cold Start Conditions Using Simulink

2000 ◽  
Vol 123 (1) ◽  
pp. 117-124 ◽  
Author(s):  
H.-Q. Liu ◽  
N. G. Chalhoub ◽  
N. Henein
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Cold Start ◽  
Operating Conditions ◽  
Combustion Model ◽  
Nonlinear Dynamic Model ◽  
Single Cylinder ◽  
Engine Model ◽  
Simulink Model ◽  
Engine Components

A nonlinear dynamic model is developed in this study to simulate the overall performance of a naturally aspirated, single cylinder, four-stroke, direct injection diesel engine under cold start and fully warmed-up conditions. The model considers the filling and emptying processes of the cylinder, blowby, intake, and exhaust manifolds. A single zone combustion model is implemented and the heat transfer in the cylinder, intake, and exhaust manifolds are accounted for. Moreover, the derivations include the dynamics of the crank-slider mechanism and employ an empirical model to estimate the instantaneous frictional losses in different engine components. The formulation is coded in modular form whereby each module, which represents a single process in the engine, is introduced as a single block in an overall Simulink engine model. The numerical accuracy of the Simulink model is verified by comparing its results to those generated by integrating the engine formulation using IMSL stiff integration routines. The engine model is validated by the close match between the predicted and measured cylinder gas pressure and engine instantaneous speed under motoring, steady-state, and transient cold start operating conditions.

Engine Analysis of Single Cylinder DI Diesel Engine Fuelled With Sunflower Oil, Sunflower Oil Methyl Ester and Its Blends

2006 ◽  
Author(s):  
V. Anandram ◽  
S. Ramakrishnan ◽  
J. Karthick ◽  
S. Saravanan ◽  
G. LakshmiNarayanaRao
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Sunflower Oil ◽  
Direct Injection ◽  
Emission Characteristics ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Di Diesel Engine ◽  
Engine Emission ◽  
Oil Sunflower

In the present work, the combustion, performance and emission characteristics of sunflower oil, sunflower methyl ester and its blends were studied and compared with diesel by employing them as fuel in a single cylinder, direct injection, 4.4 KW, air cooled diesel engine. Emission measurements were carried out using five-gas exhaust gas analyzer and smoke meter. The performance characteristics of Sunflower oil, Sunflower methyl ester and its blends were comparable with those of diesel. The components of exhaust such as HC, CO, NOx and soot concentration of the fuels were measured and presented as a function of load and it was observed that the blends had similar performance and emission characteristics as those of diesel. NOx emissions of sunflower oil methyl ester were slightly higher than that of diesel but that of sunflower oil was slightly lower than that of diesel. With respect to the combustion characteristics it was found that the biofuels have lower ignition delay than diesel. The heat release rate was very high for diesel than for the biofuel.

scholarly journals Performance Assessment of DI-Diesel Engine using the Blend of Sunflower Oil and Rice Bran Oil

2019 ◽  
Vol 8 (4) ◽  
pp. 4048-4052
Keyword(s):  
Diesel Engine ◽  
Sunflower Oil ◽  
Fuel Injection ◽  
Rice Bran Oil ◽  
Engine Performance ◽  
Performance And Emission ◽  
Animal Fats ◽  
Di Diesel Engine ◽  
Hc Emissions ◽  
Direct Fuel Injection

Biodiesel, a derivative of vegetable oils and animal fats, is used nowadays as an alternative renewable and sustainable fossil fuel. In this work, the investigation of manufacture, characterization, and results of biodiesel blends are carried out using two important feedstock’s, sunflower oil and ricebran oil on engines. For the collective advantageous of sunflower oil and ricebran oil, the two biodiesels are combined together and the mixture is analysed to assess the engine performance and emission characteristics. NaOH catalyzed transesterification process is used for producing the Biodiesels A 4.4 kW, four-stroke, single-cylinder and direct fuel injection diesel engine is used for measuring physic-chemical with full load and varying speed conditions and using the specifications of ASTM D6751 standard, the properties are compared. It is observed that the Biodiesel mixtures produce a low brake torque and high brake-specific fuel consumption (BSFC) in addition to the reduction of CO and HC emissions. NOx, however, is reduced considerably with the improvement of brake thermal efficiency. The Performance analysis indicates that the mixture of sunflower oil and ricebran oil improves performance and emission characterizes over sunflower oil and ricebran oil biodiesel when they are unmixed..

scholarly journals Performance Evaluation of Single Cylinder Diesel Engine Using Tyre Pyrolysis Oil (TPO) Blends

2019 ◽  
Vol 7 (2) ◽  
pp. 46-51
Author(s):  
P M Bhatt
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Petroleum Products ◽  
Permissible Limit ◽  
Pyrolysis Oil ◽  
Single Cylinder ◽  
Performance And Emission ◽  
Partial Load ◽  
Alternate Fuels

Increasing industrialization and motorization led to a significant rise in demand of petroleum products. As these are the non-renewable resources, it will be troublesome to predict the availability of these resources in the future, resulting in uncertainty in its supply and price and is impacting growing economies like India importing 80% of the total demand of the petroleum products. Many attempts have been made by different researchers to find out alternate fuels for Internal Combustion engines. Many alternate fuels like Biodiesel, LPG (Liquefied Petroleum Gas), CNG (Compressed Natural Gas) and Alcohol are being used nowadays by different vehicles. In this context pyrolysis of scrap tyres can be used effectively to produce oil, thereby solving the problem of waste tyre disposal. In the present study, Experimental investigations were carried out to evaluate the performance and emission characteristics of a single cylinder diesel engine fueled by TPO10, TPO15, and TPO20 at a crank angle 280 before TDC (Top Dead Centre) and injection pressure of 180 bar keeping the blend quality by controlling the density and viscosity of tyre pyrolysis oil within permissible limit of euro IV diesel requirement. The performance and emission results were analyzed and compared with that of diesel fuel operation. The results of investigations indicate that the brake thermal efficiency of the TPO - DF blend decreases by 4 to 8%. CO emissions are slightly higher but within permissible limit of euro IV emission standards. HC emissions are higher by about 40 to 60% at partial load whereas smoke opacity is lower by about 14% to 22% as compared to diesel fuel.

Sign in / Sign up

Export Citation Format

Share Document