scholarly journals Experimental investigations of winglet effects on blade geometry of small horizontal axis wind turbine rotors

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Research Work ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Experimental Investigations ◽  
Horizontal Axis Wind Turbine ◽  
Blade Geometry

In this research work, the investigation and optimization of small horizontal axis wind turbine blade at low wind speed is pursued. The experimental blades were developed using the 3D printing additive manufacturing technique. The airfoils E210, NACA2412, S1223, SG6043, E216, NACA4415, SD7080, SD7033, S1210 and MAF were tested at the wind speed of 2-6 m/s. The airfoils and optimum blade geometry were investigated with the aid of the Xfoil software at Reynolds number of 100,000. The initial investigation range included tip speed ratios from 3 to 10, solidity from 0.0431 – 0.1181 and angle of attacks from 2o to 20o. Later on these parameters were varied in MATLAB and Xfoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift to drag ratio. The cut-in wind speed of the rotors was 2 and 2.5 m/s with the winglet-equipped blades and without winglets. It was found that the E210, SG6043, E216 NACA4415 and MAF airfoil displayed better performance than the NACA 2412, S1223, SD7080, S1210 & SD7003 for the geometry optimized for the operating conditions and manufacturing method described.

Experimental investigations and aerodynamic shape optimization of small horizontal axis wind turbine blades

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
S Prakash
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Turbine Blades ◽  
Research Work ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Wind Turbine Blades ◽  
Horizontal Axis Wind Turbine ◽  
The Impact ◽  
Blade Geometry

This paper aims to optimize and investigate the small horizontal axis wind turbine blades at low wind speed. The objective of this research work is to explain the design method based on BEM theory for 0.2 m blade rotors with constant, variable and linear chord with twisted blade geometry. MATLAB and Xfoil programs were used for BEM principles and wind turbines with SG6043 airfoil. A numerical and experimental study was carried out to examine the impact of rotor solidity from 0.057 to 0.207 and the number of blades from 3 to 7 in this research work. The experimental blades were developed by using the 3D printing additive manufacturing technique. The investigation of the rotors has been done in an open wind tunnel, at wind speed from 2 to 8 m/s. The initial investigation range included tip speed ratios from 2 to 8, and angle of attacks from 2 to 20°. Later on these parameters were varied in Matlab and Xfoil software optimization and investigation of the power coefficient, blade geometry, number of blades and blade pitch angle. It was found that the rotor solidity 0.055 to 0.085 displayed better performances.

scholarly journals Investigation of an Innovative Rotor Modification for a Small-Scale Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2649 ◽  
Author(s):  
Artur Bugała ◽  
Olga Roszyk
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Airflow Distribution

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

scholarly journals PENGARUH KECEPATAN ANGIN DAN VARIASI JUMLAH SUDU TERHADAP UNJUK KERJA TURBIN ANGIN POROS HORIZONTAL

2013 ◽  
Vol 3 (1) ◽  
Author(s):  
Firman Aryanto ◽  
Made Mara ◽  
Made Nuarsa
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Mechanical Energy ◽  
Performance Testing ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Maximum Speed ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds

The wind turbine is a device that converts wind energy into mechanical energy and then converted into electrical energy through a generator. Horizontal axis wind turbines can increase the efficiency to get the maximum power coefficient. One was using the blade numerous. Maximum efisiensi system will increase the number of watts (power) generated so as to obtain a certain number of watts by simply using the number of windmills lessThe object of this research is the performance testing horizontal axis wind turbine with wind speed variation and variation in terms of the number of blade Efisiensi system (𝜂 )  and Tip Speed Ratio (TSR). Research conducted with the wind coming from the source to the Wind Tunnel fan to direct wind. Wind speed is used there are three variations of the 3 m/s, 3.5 m/s, and 4 m/s and varying the amount of blade that is 3, 4, 5 and 6 blade.The results showed that the best 𝜂  values obtained at a maximum wind speed of 4 m / s and the number of blade 5 with a value of 3.07% 𝜂, whereas 𝜂 smallest value obtained at wind speeds of 3 m/s and the number of blade 3 that the value of 0.05% 𝜂. For TSR maximum value at a maximum speed of 4 m/s occurred in the number of blade 5 is equal to λ = 2.11, while the lowest value at wind speeds of 3 m/s resulting in blade number 3 is equal to λ = 1.49.

scholarly journals Horizontal axis wind turbine modelling and data analysis by multilinear regression

2020 ◽  
Vol 11 (2) ◽  
pp. 447-464
Author(s):  
Paulaiyan Tittus ◽  
Paul Mary Diaz
Keyword(s):  
Regression Analysis ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Design Parameters ◽  
Multilinear Regression ◽  
Horizontal Axis Wind Turbine ◽  
Multilinear Regression Analysis ◽  
Turbine Performance

Abstract. The modelling of each horizontal axis wind turbine (HAWT) differs due to variation in operating conditions, dynamic parameters, and components. Thus, the choice of profiles also varies for specific applications. So for the better choice of profiles, the wind turbine performance is analysed for different parameters and working conditions. The efficiency of HAWTs mainly depends on the blade, which in turn is related to the profile of the blade, blade orientation, and tip size. Hence, the main aim of the present work is to evaluate the performance of HAWTs for three different blade tip sizes and six different blade twist angles for three major NACA (National Advisory Committee for Aeronautics) airfoils. A statistical analysis is also carried out to find the influence of different performance parameters such as drag, lift, vorticity, and normal force. The static design parameters are considered based on the available literature. A three-bladed offshore HAWT is adopted as the research object in the study. Data visualization using star glyphs and sunray plots is performed, along with multilinear regression analysis. From the multilinear regression analysis and reliable empirical correlations, it is known that drag coefficient and lift coefficient parameters have less significance in contrast to the other parameters which have more significance in the regression model. The different results obtained in terms of parametric coefficients provide an effective way to generate appropriate airfoil profiles for given HAWTs. Thus, the study helps to achieve better turbine performance, and it serves as a benchmark for future studies on HAWTs.

scholarly journals Canard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds

2020 ◽  
Vol 37 ◽  
pp. 63-71
Author(s):  
Yui-Chuin Shiah ◽  
Chia Hsiang Chang ◽  
Yu-Jen Chen ◽  
Ankam Vinod Kumar Reddy
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Optimum Parameters ◽  
Low Wind Speeds

ABSTRACT Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.

Small Horizontal Axis Wind Turbine: Analytical Blade Design and Comparison With RANS-Prediction and First Experimental Data

2013 ◽  
Author(s):  
Tom Gerhard ◽  
Michael Sturm ◽  
Thomas H. Carolus
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
Wind Turbine ◽  
Horizontal Axis ◽  
Analytical Models ◽  
Power Coefficient ◽  
Analysis Tool ◽  
Computational Domain ◽  
Horizontal Axis Wind Turbine ◽  
Data Set

State-of-the-art wind turbine performance prediction is mainly based on semi-analytical models, incorporating blade element momentum (BEM) analysis and empirical models. Full numerical simulation methods can yield the performance of a wind turbine without empirical assumptions. Inherent difficulties are the large computational domain required to capture all effects of the unbounded ambient flow field and the fact that the boundary layer on the blade may be transitional. A modified turbine design method in terms of the velocity triangles, Euler’s turbine equation and BEM is developed. Lift and drag coefficients are obtained from XFOIL, an open source 2D design and analysis tool for subcritical airfoils. A 3 m diameter horizontal axis wind turbine rotor was designed and manufactured. The flow field is predicted by means of a Reynolds-averaged Navier-Stokes simulation. Two turbulence models were utilized: (i) a standard k-ω-SST model, (ii) a laminar/turbulent transition model. The manufactured turbine is placed on the rooftop of the University of Siegen. Three wind anemometers and wind direction sensors are arranged around the turbine. The torque is derived from electric power and the rotational speed via a calibrated grid-connected generator. The agreement between the analytically and CFD-predicted kinematic quantities up- and downstream of the rotor disc is quite satisfactory. However, the blade section drag to lift ratio and hence the power coefficient vary with the turbulence model chosen. Moreover, the experimentally determined power coefficient is considerably lower as predicted by all methods. However, this conclusion is somewhat preliminary since the existing experimental data set needs to be extended.

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

scholarly journals Numerical investigation of stall characteristics for winglet blade of a horizontal axis wind turbine

2021 ◽  
Vol 321 ◽  
pp. 03004
Author(s):  
Shalini Verma ◽  
Akshoy Ranjan Paul ◽  
Anuj Jain ◽  
Firoz Alam
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Numerical Investigation ◽  
Turbulence Intensity ◽  
Geometric Modeling ◽  
Cfd Simulation ◽  
Lift Coefficient ◽  
Horizontal Axis ◽  
Renewable Energy Resources ◽  
Horizontal Axis Wind Turbine

Wind energy is one of the renewable energy resources which is clean and sustainable energy and the wind turbine is used for harnessing energy from the wind. The blades are the key components of a wind turbine to convert wind energy into rotational energy. Recently, wingtip devices are used in the blades of horizontal axis wind turbine (HAWT), which decreases the vortex and drag, while increases the lift and thereby improve the performance of the turbine. In the present study, a winglet is used at the tip of an NREL phase VI wind turbine blade. Solidworks, Pointwise, and Ansys-Fluent are used for geometric modeling, computational grid generation, and CFD simulation, respectively. The computational result obtained using SST k-ω turbulence modeling is well validated with the experimental data of NREL at 5 and 7 m/s of wind speeds. Numerical investigation of stall characteristics is carried out for wingleted blade at higher turbulence intensity (21% and 25%) and angle of attack (00 to 300 at 50 intervals) at 7 m/s wind speed. The result found that wingletd blade delay stall to 150 for both the cases of turbulence intensity. Increasing the turbulence intensity increases the lift coefficient at stall angle but drag coefficient also increases and thus a lower aerodynamic performance (CL/CD ratio = 13) is obtained. Wingleted blade improves the performance as the intensity of vortices is smaller compared to baseline blade

scholarly journals Efficient contribution of partially tip cascaded horizontal-axis wind turbine

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401989211
Author(s):  
Deyaa Nabil Elshebiny ◽  
Ali AbdelFattah Hashem ◽  
Farouk Mohammed Owis
Keyword(s):  
Wind Turbine ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
National Renewable Energy Laboratory ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Knowing That ◽  
Turbine Performance ◽  
Blade Tip

This article introduces novel blade tip geometric modification to improve the aerodynamic performance of horizontal-axis wind turbine by adding auxiliary cascading blades toward the tip region. This study focuses on the new turbine shape and how it enhances the turbine performance in comparison with the classical turbine. This study is performed numerically for National Renewable Energy Laboratory Phase II (non-optimized wind turbine) taking into consideration the effect of adding different cascade configurations on the turbine performance using ANSYS FLUENT program. The analysis of single-auxiliary and double-auxiliary cascade blades has shown an impact on increasing the turbine power of 28% and 76%, respectively, at 72 r/min and 12.85 m/s of wind speed. Knowing that the performance of cascaded wind turbine depends on the geometry, solidity and operating conditions of the original blade; therefore, these results are not authorized for other cases.

Sign in / Sign up

Export Citation Format

Share Document