STUDY ON FORMING FORCES OF PARTS PROCESSED BY SINGLE POINT INCREMENTAL FORMING WITH DUMMY SHEET

2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Vikas Sisodia ◽  
Shailendra Kumar
Keyword(s):  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Sheet Thickness ◽  
Single Point Incremental Forming ◽  
Forming Force ◽  
Step Size ◽  
Wall Angle ◽  
Influence Of Process Parameters

The present paper describes the experimental investigation on influence of process parameters on maximum forming force in Single Point Incremental Forming (SPIF) process using dummy sheet. Process parameters namely dummy sheet thickness, tool size, step size, wall angle and feed rate are selected. Taguchi L18 orthogonal array is used to design the experiments. From the analysis of variance (ANOVA) dummy sheet thickness, tool size, step size and wall angle are significant process parameters while feed rate is insignificant. It is found that as dummy sheet thickness, tool size, step size and wall angle increase magnitude of peak forming force increases while there is marginal decrease in forming force as feed rate increases. Predictive model is also developed for forming force. Validation tests are performed in order to check the accuracy of developed model. Optimum set of process parameters is also determined to minimize forming force. Experimental results are in good agreement with results predicted by the developed mathematical model.

scholarly journals Central Composite Design Optimisation in Single Point Incremental Forming of Truncated Cones from Commercially Pure Titanium Grade 2 Sheet Metals

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3634
Author(s):  
Marcin Szpunar ◽  
Robert Ostrowski ◽  
Tomasz Trzepieciński ◽  
Ľuboš Kaščák
Keyword(s):  
Surface Roughness ◽  
Central Composite Design ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Pure Titanium ◽  
Single Point Incremental Forming ◽  
Forming Force ◽  
Step Size ◽  
Central Composite

Single point incremental forming (SPIF) is an emerging process that is well-known to be suited for fabrication in small series production. The aim of this paper was to determine the optimal input parameters of the process in order to minimise the maximum of both the axial and the in-plane components of the forming force achieved during SPIF and the surface roughness of the internal surface of truncated-cone drawpieces. Grade 2 pure titanium sheets with a thickness of 0.4 mm were used as the test material. The central composite design and response surface method was used to determine the number of experiments required to study the responses through building a second-order quadratic model. Two directions of rotation of the forming tool were also considered. The input parameters were spindle speed, tool feed rate, and step size. The mathematical relations were defined using the response surfaces to predict the surface roughness of the drawpieces and the components of the forming force. It was found that feed rate has an insignificant role in both axial and in-plane forming forces, but step size is a major factor affecting axial and radial forming forces. However, step size directly affects the surface roughness on the inner surfaces of the drawpieces. Overall, the spindle speed −579 rpm (clockwise direction), tool feed 2000 mm/min, and step size 0.5 mm assure a minimisation of both force components and the surface roughness of drawpieces.

Improve the Micro-hardness of Single Point Incremental Forming Product Using Magnetic Abrasive Finishing

2020 ◽  
Vol 38 (8A) ◽  
pp. 1137-1142
Author(s):  
Baqer A. Ahmed ◽  
Saad K. Shather ◽  
Wisam K. Hamdan
Keyword(s):  
Vickers Hardness ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Step Size ◽  
Coil Current ◽  
Magnetic Abrasive Finishing ◽  
Finishing Process ◽  
Abrasive Finishing

In this paper the Magnetic Abrasive Finishing (MAF) was utilized after Single Point Incremental Forming (SPIF) process as a combined finishing process. Firstly, the Single Point Incremental forming was form the truncated cone made from low carbon steel (1008-AISI) based on Z-level tool path then the magnetic abrasive finishing process was applied on the surface of the formed product. Box-Behnken design of experiment in Minitab 17 software was used in this study. The influences of different parameters (feed rate, machining step size, coil current and spindle speed) on change in Micro-Vickers hardness were studied. The maximum and minimum change in Micro-Vickers hardness that achieved from all the experiments were (40.4 and 1.1) respectively. The contribution percent of (feed rate, machining step size, coil current and spindle speed) were (7.1, 18.068, 17.376 and 37.894) % respectively. After MAF process all the micro surface cracks that generated on the workpiece surface was completely removed from the surface.

The Effected of Single Point Incremental Forming Process Parameters on the Formed Part Surface Roughness

2014 ◽  
Vol 979 ◽  
pp. 335-338
Author(s):  
Kittiphat Rattanachan ◽  
Chatchapol Chungchoo
Keyword(s):  
Surface Roughness ◽  
Sheet Metal ◽  
Process Parameters ◽  
Feed Rate ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Tool Rotational Speed ◽  
Forming Process ◽  
Inner Surface

The single point incremental forming process (SPIF) are suited for sheet metal prototyping, because it is a low cost production process that produces sheet metal part without any used of die, and easy to adjust the part’s geometry by change toolpath. But the quality of forming parts is still in doubt. In some applications, such as mould cavity for rapid mould and the medical parts, in this case the inside surface roughness plays an importance role. In this paper, the SPIF process parameters that affected to the inner surface roughness were experimental studied. The investigated parameters are composing of tool feed rate, side overlap, depth step and tool radius. The 2k-p factorial experimental design was used to analyze the interaction between each parameter. The results showed that increasing feed rate and depth step decreased inner surface roughness. Reducing tool rotational speed and feed rate reduced inner surface roughness. So increasing depth step with decreasing side overlap reduced inner surface roughness. The large tool radius and lower side overlap improved inner surface roughness. The large tool radius and higher depth step improved inner surface roughness. And last, reducing tool rotational speed with larger tool radius, the inner surface roughness is decreased.

Force Modeling in Single Point Incremental Forming of Variable Wall Angle Components

2011 ◽  
Vol 473 ◽  
pp. 833-840 ◽  
Author(s):  
Rogelio Pérez-Santiago ◽  
Isabel Bagudanch ◽  
Maria Luisa García-Romeu
Keyword(s):  
Incremental Forming ◽  
Single Point ◽  
Fem Simulation ◽  
Single Point Incremental Forming ◽  
Forming Force ◽  
Wall Angle ◽  
Important Indicator ◽  
Force Modeling ◽  
Variable Wall ◽  
Computational Intelligence Methods

Prediction of forming forces in Incremental Sheet Forming (ISF) is specially important in the case of using adapted machinery not designed for the process. Moreover, forming force is an important indicator that can be monitored on-line and utilized for real time process control. Besides experimentation, simulations based on the Finite Element Method (FEM) have been utilized as a reliable source of process force data. Nevertheless, the long solution times required to simulate ISF renders difficult its inclusion into a process optimization chain. In consequence, models that predict the forces required to manufacture simple parts have appeared. This work begins with a review of forming force models available for Single Point Incremental Forming (SPIF). Then, an equation recently proposed in the literature is compared with published experimental results of SPIF under different working conditions. The same data is employed to verify our own FEM simulations. Finally, the above-mentioned formula and FEM simulation were applied to predict the forming force of Variable Wall Angle (VWA) geometries where available force information is limited. Besides the applicability assessment of the equation, results will supplement a future experimental campaign focused in modeling geometries of intermediate complexity level by means of Computational Intelligence methods.

scholarly journals Study of the Effect of Process Parameters on Surface Profile Accuracy in Single-Point Incremental Sheet Forming of AA1050-H14 Aluminum Alloy

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Abdulmajeed Dabwan ◽  
Adham E. Ragab ◽  
Mohamed A. Saleh ◽  
Saqib Anwar ◽  
Atef M. Ghaleb ◽  
...  
Keyword(s):  
Surface Quality ◽  
Process Parameters ◽  
Incremental Forming ◽  
Single Point ◽  
Surface Profile ◽  
Sheet Thickness ◽  
Numerical Control ◽  
Single Point Incremental Forming ◽  
Tool Diameter ◽  
Profile Accuracy

Single-point incremental forming is an innovative flexible and inexpensive technique to form sheet products when prototypes or small batches are required. The process allows complex geometries to be produced using a computer numerical control machine, eliminating the need for a special die. This study reports on the effects of four important single-point incremental forming process parameters on produced surface profile accuracies. The profile accuracy was estimated by measuring the side angle errors and surface roughness and also waviness and circularity of the product inner surface. Full factorial design of experiments was used to plan the study, and the analysis of variance was used to analyze and interpret the results. The results indicate that the tool diameter (d), step depth (s), and sheet thickness (t) have significant effects on the produced profile accuracy, while the feed rate (f) is not significant. As a general rule, thin sheets with greater tool diameters yielded the best surface quality. The results also show that controlling all surface quality features is complex because of the contradicting effects of, and interactions between, a number of the process parameters.

scholarly journals Study of Friction and Wear Effects in Aluminum Parts Manufactured via Single Point Incremental Forming Process Using Petroleum and Vegetable Oil-Based Lubricants

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3973
Author(s):  
José M. Diabb Zavala ◽  
Oscar Martínez-Romero ◽  
Alex Elías-Zúñiga ◽  
Héctor Manuel Leija Gutiérrez ◽  
Alejandro Estrada-de la Vega ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Friction And Wear ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Forming Process ◽  
Step Size ◽  
Vertical Step ◽  
Stribeck Curves

This paper focuses on studying how mineral oil, sunflower, soybean, and corn lubricants influence friction and wear effects during the manufacturing of aluminum parts via the single point incremental forming (SPIF) process. To identify how friction, surface roughness, and wear change during the SPIF of aluminum parts, Stribeck curves were plotted as a function of the SPIF process parameters such as vertical step size, wall angle, and tool tip semi-spherical diameter. Furthermore, lubricant effects on the surface of the formed parts are examined by energy dispersive spectroscopy (EDS) and scanning electron microscope (SEM) images, the Alicona optical 3D measurement system, and Fourier-transform infrared spectroscopy (FTIR). Results show that during the SPIF process of the metallic specimens, soybean and corn oils attained the highest friction, along forces, roughness, and wear values. Based on the surface roughness measurements, it can be observed that soybean oil produces the worst surface roughness finish in the direction perpendicular to the tool passes (Ra =1.45 μm) considering a vertical step size of 0.25 mm with a 5 mm tool tip diameter. These findings are confirmed through plotting SPIFed Stribeck curves for the soybean and corn oils that show small hydrodynamic span regime changes for an increasing sample step-size forming process. This article elucidates the effects caused by mineral and vegetable oils on the surface of aluminum parts produced as a function of Single Point Incremental Sheet Forming process parameters.

scholarly journals Effect of hardening law and process parameters on finite element simulation of single point incremental forming (SPIF) of 7075 aluminum alloy sheet

2020 ◽  
Vol 21 (3) ◽  
pp. 302 ◽  
Author(s):  
Rasoul Esmaeilpour ◽  
Hyunki Kim ◽  
Taejoon Park ◽  
Farhang Pourboghrat ◽  
Akshat Agha ◽  
...  
Keyword(s):  
Process Parameters ◽  
Strain Distribution ◽  
Incremental Forming ◽  
Single Point ◽  
Single Point Incremental Forming ◽  
Effective Plastic Strain ◽  
Step Size ◽  
Hardening Law ◽  
Element Simulation ◽  
Tool Force

In the last two decades, the advances of using computers in sheet metal forming processes have introduced a novel adjustable process known as incremental sheet forming (ISF) as an optimal method for fast prototyping and low numbers of production. Formability and deformation behavior of ISF process are highly affected by the selected process parameters, such as the toolpath, step size, tool diameter, feed rate, and lubrication. The purpose of this work was to study the effect of these process parameters as well as hardening law on single point incremental forming (SPIF) process. For this work, a truncated-cone geometry was considered as a target shape with 7075-O aluminum alloy sheets. The simulations were conducted with different process parameters, i.e., toolpath type, step size, tool size, feed rate, friction coefficient, and wall angle with respect to the tool force and moment, effective plastic strain distribution and thickness of the part. In addition, three types of hardening laws i.e., isotropic extended Voce type hardening law, combined isotropic-kinematic Chaboche type hardening laws with single and double back-stress terms were applied in the finite element simulation of SPIF process. A detailed comparison of these hardening laws' predictions was made with respect to the tool force and moment, effective plastic strain distribution and thickness of the part.

Sign in / Sign up

Export Citation Format

Share Document