The Influence of Loads Superposition, Deterioration Due to Cracks and Residual Stresses on the Strength of Tubular Junction

2017 ◽  
Vol 68 (6) ◽  
pp. 1267-1273
Author(s):  
Valeriu V. Jinescu ◽  
Angela Chelu ◽  
Gheorghe Zecheru ◽  
Alexandru Pupazescu ◽  
Teodor Sima ◽  
...  
Keyword(s):  
Stress Concentration ◽  
Residual Stresses ◽  
Bending Moment ◽  
Combined Loading ◽  
Torsional Moment ◽  
Calculation Methods ◽  
State Of Stress ◽  
Cracked Structures ◽  
Total Participation ◽  
Theoretical Results

In the paper the interaction of several loads like pressure, axial force, bending moment and torsional moment are analyzed, taking into account the deterioration due to cracks and the influence of residual stresses. A nonlinear, power law, of structure material is considered. General relationships for total participation of specific energies introduced in the structure by the loads, as well as for the critical participation have been proposed. On these bases: - a new strength calculation methods was developed; � strength of tubular cracked structures and of cracked tubular junction subjected to combined loading and strength were analyzed. Relationships for critical state have been proposed, based on dimensionless variables. These theoretical results fit with experimental date reported in literature. On the other side stress concentration coefficients were defined. Our one experiments onto a model of a pipe with two opposite nozzles have been achieved. Near one of the nozzles is a crack on the run pipe. Trough the experiments the state of stress have been obtained near the tubular junction, near the tip of the crack and far from the stress concentration points. On this basis the stress concentration coefficients were calculated.

Effect of Torsion on Collapse Bending Moment for 24-Inch Diameter Schedule 80 Pipes With Wall Thinning

2012 ◽  
Author(s):  
Kunio Hasegawa ◽  
Yinsheng Li ◽  
Bostjan Bezensek ◽  
Phuong Hoang
Keyword(s):  
Power Plants ◽  
Bending Moment ◽  
Combined Loading ◽  
Bending Moments ◽  
Compressive Stresses ◽  
Wall Thinning ◽  
Nominal Thickness ◽  
Calculation Results ◽  
Loading Modes ◽  
Local Wall Thinning

Piping items in power plants may experience combined bending and torsion moments during operation. Currently, there is a lack of guidance in the ASME B&PV Code Section XI for combined loading modes including pressure, torsion and bending. Finite element analyses were conducted for 24-inch diameter Schedule 80 pipes with local wall thinning subjected to tensile and compressive stresses. Plastic collapse bending moments were calculated under constant torsion moments. From the calculation results, it can be seen that collapse bending moment for pipes with local thinning subjected to tensile stress is smaller than that subjected to compressive stress. In addition, equivalent moment is defined as the root the sum of the squares of the torsion and bending moments. It is found that the equivalent moments can be approximated with the pure bending moments, when the wall thinning length is equal or less than 7.73R·t for the wall thinning depth of 75% of the nominal thickness, where R is the mean radius and t is the wall thickness of the pipe.

Prediction Method for Plastic Collapse of Pipes Subjected to Combined Bending and Torsion Moments

2010 ◽  
Author(s):  
Yinsheng Li ◽  
Kunio Hasegawa ◽  
Phuong H. Hoang ◽  
Bostjan Bezensek
Keyword(s):  
Entire Range ◽  
Estimation Method ◽  
Prediction Method ◽  
Bending Moment ◽  
Combined Loading ◽  
Plastic Collapse ◽  
Finite Element Analyses ◽  
Pure Torsion ◽  
Stainless Steel Pipe ◽  
Service Inspection

When a crack is detected in a pipe during in-service inspection, the failure estimation method given in the codes such as ASME Boiler and Pressure Vessel Code Section XI non-mandatory Appendix C or JSME S NA-1-2008 Appendix E-8 can be applied to assess the integrity of the pipe. In the current editions of these codes, the failure estimation method is provided for bending moment and pressure. Torsion load is assumed to be relatively small and is not considered in the method. In this paper, finite element analyses are conducted for 24-inch stainless steel pipe with a circumferential surface crack subjected to the combined bending and torsion moments, focusing on large and pure torsion moments. Based on the analysis results, a prediction method for plastic collapse under the combined loading conditions of bending and torsion is proposed for the entire range of torsion moments.

Elasto-Plastic Stress Distribution in Triplate Joint Assembly under Bending Moment

2007 ◽  
Vol 345-346 ◽  
pp. 1437-1440
Author(s):  
Tae Hyun Baek ◽  
Seung Kee Koh ◽  
Jie Cheng
Keyword(s):  
Finite Element Method ◽  
Residual Stresses ◽  
Pure Aluminum ◽  
Main Tool ◽  
Bending Moment ◽  
The Finite Element Method ◽  
Shipbuilding Industry ◽  
Structural Parts ◽  
Von Mises

Pre-produced triplate transition joint assemblies are widely used in shipbuilding industry to make welds between aluminum and steel for a number of years now. The straight-shaped transition joint assemblies are bent during shipbuilding. So it is necessary to study the residual stresses created by punch forming, which would have heavy effects on the quality of structural parts. ABAQUS is a suite of powerful engineering simulation programs, based on the finite element method. In this paper, ABAQUS was used as the main tool to simulate the residual stresses in a triplate transition joint after unloading. Punch-pressing was carried to simulate bending moment in ABAQUS. The triplate is consisted of baselayer (steel: Lloyd’s Shipplate Gr. A), interlayer (pure aluminum: Al99.5) and superlayer (Al-Mg alloy: AlMg4.5Mn). Results from the ABAQUS analysis showed that increasing the radius of punch significantly reduced the von Mises residual stresses in steel. Changes of von Mises residual stresses in interlayer (Al99.5) and superlayer (AlMg4.5Mn) were negligible.

Analysis of Stress Concentrations in Thick Cylinders With Sideholes and Crossholes

1972 ◽  
Vol 94 (3) ◽  
pp. 815-824 ◽  
Author(s):  
J. C. Gerdeen
Keyword(s):  
Stress Concentration ◽  
Stress Concentrations ◽  
Concentration Factors ◽  
Stress Concentration Factors ◽  
Experimental Values ◽  
Pressure Stress ◽  
Shrink Fit ◽  
Outside Diameter ◽  
Theoretical Results

An approximate theoretical analysis is presented for the determination of stress concentration factors in thick walled cylinders with sideholes and crossholes. The cylinders are subjected to both internal pressure and external shrink-fit pressure. Stress concentration factors are plotted as functions of the geometrical ratios of outside diameter-to-bore diameter, and bore diameter-to-sidehole diameter. Theoretical results are compared to experimental values available in the literature and results of experiments described in a separate paper.

Elastic-plastic bending of the pipeline under combined loading

2021 ◽  
pp. 372-377
Author(s):  
Виктор Миронович Варшицкий ◽  
Евгений Павлович Студёнов ◽  
Олег Александрович Козырев ◽  
Эльдар Намикович Фигаров
Keyword(s):  
Internal Pressure ◽  
Limit State ◽  
Bending Moment ◽  
Axial Direction ◽  
Longitudinal Force ◽  
Combined Loading ◽  
Dimensional Problem ◽  
Elastic Plastic ◽  
Pipeline Section ◽  
Thin Walled Pipe

Рассмотрена задача упругопластического деформирования тонкостенной трубы при комбинированном нагружении изгибающим моментом, осевой силой и внутренним давлением. Решение задачи осуществлено по разработанной методике с помощью математического пакета Matcad численным методом, основанным на деформационной теории пластичности и безмоментной теории оболочек. Для упрощения решения предложено сведение двумерной задачи к одномерной задаче о деформировании балки, материал которой имеет различные диаграммы деформирования при сжатии и растяжении в осевом направлении. Проведено сравнение с результатами численного решения двумерной задачи методом конечных элементов в упругопластической постановке. Результаты расчета по инженерной методике совпадают с точным решением с точностью, необходимой для практического применения. Полученные результаты упругопластического решения для изгибающего момента в сечении трубопровода при комбинированном нагружении позволяют уточнить известное критериальное соотношение прочности сечения трубопровода с кольцевым дефектом в сторону снижения перебраковки. Применение разработанной методики позволяет ранжировать участки трубопровода с непроектным изгибом по степени близости к предельному состоянию при комбинированном нагружении изгибающим моментом, продольным усилием и внутренним давлением. The problem of elastic plastic deformation of a thin-walled pipe under co-binned loading by bending moment, axial force and internal pressure is considered. The problem is solved by the developed method using the Matcad mathematical package by a numerical method based on the deformation theory of plasticity and the momentless theory of shells. To simplify the solution of the problem, it is proposed to reduce a twodimensional problem to a one-dimensional problem about beam deformation, the material of which has different deformation diagrams under compression and tension in the axial direction. Comparison with the results of numerical solution of the two-dimensional problem with the finite element method in the elastic plastic formulation is carried out. The obtained results of the elastic-plastic solution for the bending moment in the pipeline section under combined loading make it possible to clarify criterion ratio of the strength of the pipeline section with an annular defect in the direction of reducing the rejection. Application of the developed approach allows to rank pipeline sections with non-design bending in the steppe close to the limit state under combined loading of the pipeline with bending moment, longitudinal force and internal pressure.

Analysis on Deformation of Pre-Splitting Steel Reinforced Concrete Beams Strengthened by Prestressed CFRP

2011 ◽  
Vol 243-249 ◽  
pp. 929-933
Author(s):  
Na Ha ◽  
Lian Guang Wang ◽  
Shen Yuan Fu
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Concrete Beams ◽  
Bending Moment ◽  
Reinforced Concrete Beams ◽  
Steel Reinforced Concrete ◽  
Cfrp Sheets ◽  
Deformation Curves ◽  
Prestressed Cfrp Sheets ◽  
Theoretical Results

In order to improve the bearing capacity of SRC which is related with deformation and stiffiness, SRC beams should be strengthened by CFRP. Based on the experiment of six pre-splitting steel reinforced concrete beams strengthened with (Prestressed) CFRP sheets, the deformation of beams are discussed. Load-deformation curves are obtained by the experiment. Considering the influence of intial bending moment on SRC beams, the calculated deformation formulas of SRC beams strengthened by (Prestressed) CFRP are deduced. The results showed that the load-deformation curves of normal and strengthened beams respectively showed three and two linear characteristics. The theoretical results which calculated by the formulas of deformation are well agreement with the experimental results.

A Simple Approach for Including Weld Residual Stresses in the Calculation of Pipe Circumferential Through-Wall Crack Opening Displacements

2016 ◽  
Author(s):  
Richard Olson
Keyword(s):  
Residual Stresses ◽  
Axial Force ◽  
Analytic Solution ◽  
Crack Opening ◽  
Bending Moment ◽  
Generalized Solution ◽  
Finite Element Analyses ◽  
Opening Displacement ◽  
Crack Face ◽  
Basic Equations

Current methodologies for predicting the crack opening displacement (COD) of circumferentially through-wall cracked pipe do not include the effect of weld residual stresses (WRS). Even the most advanced COD prediction methodology only includes the effect of applied axial force, bending moment, and crack face pressure. For some years, it has been known that weld residual stresses do alter the COD, but there has been no convenient way to include them in a COD prediction without doing case-specific finite element analyses. This paper documents a generalized solution for including WRS effects on COD. The model uses a closed-form analytic solution to approximate the crack face rotations that the WRS would induce which, subsequently, can be added to the typical axial force-bending-crack face pressure COD solution. The methodology is described and the basic equations for the solution are presented. Following this, application to cases to evaluate the efficacy of the approach are presented which show a mixture of results ranging from amazingly good to “of questionable value” with respect to the FEA results.

Sign in / Sign up

Export Citation Format

Share Document