scholarly journals Production, Quantitative Analysis of Fatty Acids, Engine Performance and Emission Characteristics of Biodiesel Fuel Derived from Virgin Coconut Oil

Author(s):  
Alex Y ◽  
Roji George Roy

Biodiesel has become more attractive recently, because of its environmental benefits and the fact that it is made from renewable resources. Over the past few decades, most of the countries depending on diesel engines for transportation. Some of its valuable advantages like highest thermal efficiency made it very popular. At the same time, the cost of diesel fuel is increasing, due to the depletion of fossil fuels. In this current scenario, we need an alternative fuel instead of diesel fuel. Many of the researchers have successfully placed several works on generating energy from different types of alternative sources including solar and some kind of conversion processes including renewable agricultural products into liquid fuel. One of the biggest challenges for developing countries in relation to energy consumption is to develop and implement technologies that help to improve efficiency of automobile engines, also to reduce the emissions of harmful gases and particulate matters. In order to avoid environmental impacts, emissions are reduced or eliminated by introducing renewable energy resources. The present research chronicles the production and testing of renewable biodiesel fuel derived from virgin coconut oil on a diesel engine, to analyses the engine performance and emission characteristics. In the first phase of work, production of biodiesel fuel from virgin coconut oil using transeterification process with two types of catalysts (homogenous and heterogeneous). The preliminary results shows that, with the addition of homogenous catalyst called Potassium Hydroxide (KOH) with methanol shows much higher activity than that of heterogeneous catalysts, and it shows more similar properties with diesel fuel. The results obtained from the chemical test and physicochemical properties of transesterified biodiesel fuel clearly proves the above-mentioned statement. The chemical tests such as GCMS and FT-IR clearly shows that the biodiesel fuel has sufficient amount of volatile components and functional groups. Then, physicochemical properties include, Fire point, Flashpoint, density, and viscosity were analyzed. Finally, Engine performance and Emission characteristics were analysed to confirm, whether this biodiesel fuel is suitable for diesel engines, without any engine modifications. It was found to be, the transesterified virgin coconut oil biodiesel has similar properties to that of the diesel fuel. From the physiochemical properties and engine performance clearly shows that, coconut oil biodiesel is suitable for diesel engine on blending, at a blending percentage level of 20% with conventional diesel fuel. Since the obtained transesterified biofuel can be used as an alternative fuel for diesel engines. The several journal reports and find outs from experimental investigation clearly depicts that the efficiency of the transesterified biofuel mainly depends upon the amount of catalyst adding and type of catalysts present in the biofuel, whether it is homogenous or heterogeneous catalyst is suitable with methanol. Finally, from the analysis made from biodiesel fuel. Coconut Oil Biodiesel fuel has less emission characteristics than that of the diesel fuels.

Author(s):  
Fatima Mohammed Ghanim ◽  
Ali Mohammed Hamdan Adam ◽  
Hazir Farouk

Abstract: There is growing interest to study the effect of blending various oxygenated additives with diesel or biodiesel fuel on engine performance and emission characteristics. This study aims to analyze the performance and exhaust emission of a four-stroke, four-cylinder diesel engine fueled with biodiesel-ethanol-diesel. Biodiesel was first produced from crude Jatropha oil, and then it was blended with ethanol and fossil diesel in different blend ratios (B10E10D80, B12.5E12.5D75, B15E15D70, B20E20D60 and B25E25D50). The engine performance and emission characteristics were studied at engine speeds ranging from 1200 to 2000 rpm. The results show that the brake specific fuel consumption increases while the brake power decreases as the percentage of biodiesel and ethanol increases in the blend. The exhaust emission analysis shows a reduction in CO2 emission and increase in NOx emission when the biodiesel -to- ethanol ratio increases in the blends, when compared with diesel as a reference fuel.


2014 ◽  
Vol 607 ◽  
pp. 588-593 ◽  
Author(s):  
Amir Aziz ◽  
Ahmad Fitri Yusof ◽  
Rizalman Mamat ◽  
W.N. Azeem

An emulsion of biodiesel and water is one of the possible approaches that have been used to overcome diesel engine pollution. In this work, the performance and emission characteristics of a 4-cylinder diesel engine using pure diesel, biodiesel B20 and emulsified biodiesel were investigated. Emulsified biodiesel containing 5 % and 10 % water were utilize for the engine tests. During the experimental work, the engine was set-up at 2500 rpm and 20 % to 60 % loads. The result shows the reduction in NOx formation when the water content in emulsified biodiesel increased from 5 % to 10%. For the performance, there were no significant differences between the engine break powers measured for emulsified biodiesel containing 5% water and diesel fuel.


Author(s):  
A. K. Babu ◽  
G. Devaradjane

The intent of this paper is to summarize the state of knowledge on use of vegetable oils as diesel fuels. Fuel related properties are reviewed and compared with conventional diesel fuel. The use of neat vegetable oil (edible and/or nonedible), biodiesel and its blends in a diesel engine has been discussed. Performance and emission characteristics are highlighted. Suitability of different combustion chambers for diesel engine operation with vegetable oils is outlined. Techniques to decrease viscosities are discussed. An overview on current developments on the use of vegetable oils directly and indirectly in diesel engines is presented.


2001 ◽  
Vol 20 (1) ◽  
pp. 63-69 ◽  
Author(s):  
Herchel T.C. Machacon ◽  
Seiichi Shiga ◽  
Takao Karasawa ◽  
Hisao Nakamura

2014 ◽  
Vol 1016 ◽  
pp. 582-586 ◽  
Author(s):  
Tayfun Ozgur ◽  
Erdi Tosun ◽  
Ceyla Ozgur ◽  
Gökhan Tuccar ◽  
Kadir Aydın

In this study the performance, exhaust emission characteristics and combustion process of the engine fueled with hydrogen-diesel blends were compared to diesel fuel. Hydrogen was blended with diesel fuel at the volumetric ratios of 5%, 10% and 20%. AVL BOOST software was dedicated to simulate the performance and emission values for various blends of hydrogen with diesel fuel. The simulation results showed that hydrogen addition to diesel fuel improve both engine performance and exhaust emmisions.


Author(s):  
Ahmed I. EL-Seesy ◽  
Ali K. Abdel-Rahman ◽  
Hamdy Hassan ◽  
Shinichi Ookawara ◽  
Meshack Hawi

The current work presents the results of an experimental study that is conducted to investigate the effect of nanoparticles added to biodiesel-diesel fuel mixture. Nano-biodiesel-diesel mixture fuels were prepared by adding of multi-walled carbon nanotubes (MWCNTs). These nanoparticles were blended with biodiesel-diesel fuel in varying mass fractions using an ultrasonic stabilization. A diesel engine test rig was used to examine the effect of nanoparticles on engine performance and emission characteristics with a constant speed of 2500 rpm and different engine loads. The engine test results indicated that the biodiesel-diesel fuel blend slightly decreased the engine performance and increased its emission characteristics at all tested engine operating conditions. The use of nanoparticles was found to improve all engine performance parameters. Specifically, the maximum emission reduction was obtained at a dose level of 20 mg/l, where considerable emission reduction was observed; NOx by 14 %, CO by 30 %, and UHC by 34 %. Also, the best of both engine combustion characteristics and performance were reached at a dose level of 40–50 mg/l. Where the reduction in the brake specific fuel consumption was by 16 %, the increase in both the cylinder peak pressure Pmax, and maximum gross heat release rate dQg/dθmax. were 4 % and 1%, respectively. Finally, the recommended dose level to achieve a significant enhancement in all engine performance is 40 mg/l.


Sign in / Sign up

Export Citation Format

Share Document