scholarly journals Performance and Emission Characteristics of a Diesel Engine Fueled by Biodiesel-Ethanol-Diesel Fuel Blends

Author(s):  
Fatima Mohammed Ghanim ◽  
Ali Mohammed Hamdan Adam ◽  
Hazir Farouk

Abstract: There is growing interest to study the effect of blending various oxygenated additives with diesel or biodiesel fuel on engine performance and emission characteristics. This study aims to analyze the performance and exhaust emission of a four-stroke, four-cylinder diesel engine fueled with biodiesel-ethanol-diesel. Biodiesel was first produced from crude Jatropha oil, and then it was blended with ethanol and fossil diesel in different blend ratios (B10E10D80, B12.5E12.5D75, B15E15D70, B20E20D60 and B25E25D50). The engine performance and emission characteristics were studied at engine speeds ranging from 1200 to 2000 rpm. The results show that the brake specific fuel consumption increases while the brake power decreases as the percentage of biodiesel and ethanol increases in the blend. The exhaust emission analysis shows a reduction in CO2 emission and increase in NOx emission when the biodiesel -to- ethanol ratio increases in the blends, when compared with diesel as a reference fuel.

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
S. Debbarma ◽  
R. D. Misra

The technology for use of biodiesels (up to 20%) as alternative fuel in diesel engines has already been established. In this regard, some suitable modification of biodiesel with appropriate additives may help in increasing the biodiesel component in the biodiesel fuel blends. In order to evaluate the effects of iron nanoparticles (INP) blended palm biodiesel (PB) on the performance and emission characteristics of diesel engine, an experimental investigation is carried out in a single cylinder diesel engine. Methodically, biodiesel prepared from palm oil and commercially available nanosized INP is used in this study. Iron nanoparticles are suspended in the biodiesel in proportions of 40 ppm to 120 ppm using an ultrasonicator. The intact study is conducted in the diesel engine using the four fuel samples, namely diesel, PB20, INP50PB30, and INP75PB30, consecutively. The addition of nano-additive has resulted in higher brake thermal efficiency (BTE) by 3% and break-specific energy consumption (BSEC) by 3.3%, compared to diesel fuel. The emission levels of carbon monoxide (∼56%) and NOx (∼4%) are appreciably reduced with the addition of INP. Increase of INP in the blend from 50 ppm to 75 ppm, BTE and BSEC tend to reduce, but CO and NOx emissions are reduced.


Author(s):  
Alex Y ◽  
Roji George Roy

Biodiesel has become more attractive recently, because of its environmental benefits and the fact that it is made from renewable resources. Over the past few decades, most of the countries depending on diesel engines for transportation. Some of its valuable advantages like highest thermal efficiency made it very popular. At the same time, the cost of diesel fuel is increasing, due to the depletion of fossil fuels. In this current scenario, we need an alternative fuel instead of diesel fuel. Many of the researchers have successfully placed several works on generating energy from different types of alternative sources including solar and some kind of conversion processes including renewable agricultural products into liquid fuel. One of the biggest challenges for developing countries in relation to energy consumption is to develop and implement technologies that help to improve efficiency of automobile engines, also to reduce the emissions of harmful gases and particulate matters. In order to avoid environmental impacts, emissions are reduced or eliminated by introducing renewable energy resources. The present research chronicles the production and testing of renewable biodiesel fuel derived from virgin coconut oil on a diesel engine, to analyses the engine performance and emission characteristics. In the first phase of work, production of biodiesel fuel from virgin coconut oil using transeterification process with two types of catalysts (homogenous and heterogeneous). The preliminary results shows that, with the addition of homogenous catalyst called Potassium Hydroxide (KOH) with methanol shows much higher activity than that of heterogeneous catalysts, and it shows more similar properties with diesel fuel. The results obtained from the chemical test and physicochemical properties of transesterified biodiesel fuel clearly proves the above-mentioned statement. The chemical tests such as GCMS and FT-IR clearly shows that the biodiesel fuel has sufficient amount of volatile components and functional groups. Then, physicochemical properties include, Fire point, Flashpoint, density, and viscosity were analyzed. Finally, Engine performance and Emission characteristics were analysed to confirm, whether this biodiesel fuel is suitable for diesel engines, without any engine modifications. It was found to be, the transesterified virgin coconut oil biodiesel has similar properties to that of the diesel fuel. From the physiochemical properties and engine performance clearly shows that, coconut oil biodiesel is suitable for diesel engine on blending, at a blending percentage level of 20% with conventional diesel fuel. Since the obtained transesterified biofuel can be used as an alternative fuel for diesel engines. The several journal reports and find outs from experimental investigation clearly depicts that the efficiency of the transesterified biofuel mainly depends upon the amount of catalyst adding and type of catalysts present in the biofuel, whether it is homogenous or heterogeneous catalyst is suitable with methanol. Finally, from the analysis made from biodiesel fuel. Coconut Oil Biodiesel fuel has less emission characteristics than that of the diesel fuels.


Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4578 ◽  
Author(s):  
Fayaz Hussain ◽  
Manzoore Elahi M. Soudagar ◽  
Asif Afzal ◽  
M.A. Mujtaba ◽  
I.M. Rizwanul Fattah ◽  
...  

This study considered the impacts of diesel–soybean biodiesel blends mixed with 3% cerium coated zinc oxide (Ce-ZnO) nanoparticles on the performance, emission, and combustion characteristics of a single cylinder diesel engine. The fuel blends were prepared using 25% soybean biodiesel in diesel (SBME25). Ce-ZnO nanoparticle additives were blended with SBME25 at 25, 50, and 75 ppm using the ultrasonication process with a surfactant (Span 80) at 2 vol.% to enhance the stability of the blend. A variable compression ratio engine operated at a 19.5:1 compression ratio (CR) using these blends resulted in an improvement in overall engine characteristics. With 50 ppm Ce-ZnO nanoparticle additive in SBME25 (SBME25Ce-ZnO50), the brake thermal efficiency (BTE) and heat release rate (HRR) increased by 20.66% and 18.1%, respectively; brake specific fuel consumption (BSFC) by 21.81%; and the CO, smoke, and hydrocarbon (HC) decreased by 30%, 18.7%, and 21.5%, respectively, compared to SBME25 fuel operation. However, the oxides of nitrogen slightly rose for all the nanoparticle added blends. As such, 50 ppm of Ce-ZnO nanoparticle in the blend is a potent choice for the enhancement of engine performance, combustion, and emission characteristics.


2018 ◽  
Vol 178 ◽  
pp. 146-177 ◽  
Author(s):  
Manzoore Elahi M. Soudagar ◽  
Nik-Nazri Nik-Ghazali ◽  
Md. Abul Kalam ◽  
I.A. Badruddin ◽  
N.R. Banapurmath ◽  
...  

2014 ◽  
Vol 1016 ◽  
pp. 582-586 ◽  
Author(s):  
Tayfun Ozgur ◽  
Erdi Tosun ◽  
Ceyla Ozgur ◽  
Gökhan Tuccar ◽  
Kadir Aydın

In this study the performance, exhaust emission characteristics and combustion process of the engine fueled with hydrogen-diesel blends were compared to diesel fuel. Hydrogen was blended with diesel fuel at the volumetric ratios of 5%, 10% and 20%. AVL BOOST software was dedicated to simulate the performance and emission values for various blends of hydrogen with diesel fuel. The simulation results showed that hydrogen addition to diesel fuel improve both engine performance and exhaust emmisions.


2013 ◽  
Vol 42 (1) ◽  
pp. 38-46 ◽  
Author(s):  
M. Loganathan ◽  
A. Anbarasu ◽  
A. Velmurugan

In this study, Biodiesel -Dimethyl Ether (BDE) and Biodiesel Ethanol (BE) were tested in a 4-cylinderdirect-injection diesel engine to investigate the performance and emission characteristics of the engine underfive engine loads at the maximum torque. The engine speed was maintained at 1500 rpm. Here the jatropha oilis used as a non edible oil to produce the biodiesel. The ethanol and dimethyl ether is used as an additive toenhance the engine combustion. The BDE 5 (biodiesel 95% and dimethyl ether 5%) , BDE 10 (biodiesel 90%and dimethyl ether 10%) BDE 15(biodiesel 85% and dimethyl ether 15%) BE5 (biodiesel 95% and ethanol 5%),BE10 (biodiesel 90% and ethanol 10%) and BE15 (biodiesel 85% and ethanol 15%) were tested in the engine.The results indicate that when compared with neat jatropha, the engine performance increased and emissionlevel decreased with adding the ethanol and diethyl ether with methyl ester of jatropha oil. In comparison withneat jatropha, the BDE5 and BE15 blends have higher brake thermal efficiency (BTE) of 12% and 13%respectively. The experimental results showed that the CO, HC emission is decreased and NOx emission isincreased for higher blends of additives. The brakes specific fuel consumption (BSFC) decreased for BDE5 andBE5 compared to other combination of fuel.DOI: http://dx.doi.org/10.3329/jme.v42i1.15941 


Sign in / Sign up

Export Citation Format

Share Document