scholarly journals Electron Beam Measurements Employing Electron Montecarlo Algorithm on TrueBeam STx® and Clinac iX® Linear Accelerators

2021 ◽  
Vol 9 (B) ◽  
pp. 1730-1738
Author(s):  
Kamal Saidi ◽  
Othmane Kaanouch ◽  
Hanae El Gouach ◽  
Mohamed Reda Mesradi ◽  
Mounir Mkimel ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beams ◽  
Measured Data ◽  
Field Size ◽  
Large Field ◽  
Linear Accelerators ◽  
Tolerance Intervals ◽  
Depth Dose ◽  
Large Water ◽  
Good Agreement

Electron beam measurement comparison between TrueBeam STx® and Clinac iX® established. Data evaluation of eMC-calculated and measured for TrueBeam STx® performed. Dosimetric parameters measured including depth dose curves for each applicator, percentage depth dose (PDDs) curves without applicator, the profile in-air for a large field size 40×40 cm2, and the Absolute Dose (cGy/MU) for each applicator using a large water phantom (PTW, Freiburg, Germany), employing Roos and Markus plane-parallel ionization chambers. The data were examined for five electron beams of Varian’s TrueBeam STx® and Clinac iX® machines. A comparison between measurement PDDs and calculated by the Eclipse electron Monte Carlo (eMC) algorithm was performed to validate Truebeam STx® commissioning. The measured data indicated that electron beam PDDs from the TrueBeam STx® machine are well matched to those from Clinac iX® machine. The quality index R50 for applicator 15×15 cm2 was in the tolerance intervals. However, Surface dose (Ds) increases with increasing energy for both accelerators. Comparisons between the measured and eMC-calculated values revealed that the R100, R90, R80, and R50 values mostly agree within 5 mm. Measured and calculated bremsstrahlung tail Rp correlates well statistically. Ds agrees mostly within 2%. Electron beams were successfully validated for TrueBeam STx®, a good agreement between modeled and measured data was observed.

scholarly journals Commissioning Measurements of Electron Beam Using Montecarlo Algorithm on Truebeam STx® and Compariaon with Clinac iX Linear Accelerator

2021 ◽  
Vol 229 ◽  
pp. 01041
Author(s):  
Kamal Saidi ◽  
Redouane El Baydaoui ◽  
Hanae El Gouach ◽  
Othmane Kaanouch ◽  
Mohamed Reda Mesradi
Keyword(s):  
Electron Beam ◽  
Electron Beams ◽  
Measured Data ◽  
University Hospital ◽  
Field Size ◽  
Large Field ◽  
Water Phantom ◽  
Depth Dose ◽  
International University ◽  
The Absolute

TrueBeam STx latest generation linear accelerators (linacs) installed at Sheikh Khalifa International University Hospital in Casablanca, Morocco. The aim of this is to present and compare the result of the Electron commissioning measurement on TrueBeam Stx and clinac iX installed at Sheikh Khalifa International University Hospital in Casablanca, Morocco. A compariaon of eMC calculations and measurements for TrueBeam Stx were evaluated. Dosimetric parameters are systematically measured using a large water phantom 3D scanning system MP3 Water Phantom (PTW, Freiburg, Germany). The data of the electron beams commissioning including depth dose curves for each applicator, depth dose curves without applicator and the profile in air for a large field size 40x 40cm2, and the Absolute Dose (cGy/MU) for each applicator. All the data were examined and compared for five electron beams (E6MeV, E9MeV, E12MeV, E16MeV and E20MeV) of Varian’s TrueBeam STx and Clinac iX machines. A comparison, between measurement PDDs and calculated by the Eclipse electron Monte Carlo (eMC) algorithm were performed to validate Truebeam Stx commissioning. All this measurements were performed with a Roos and Markus plane parallel chamber. Our measured data indicated that electron beam PDDs from the TrueBeam Stx machine are well matched to those from our Varian Clinac iX machine. Significant differences between TrueBeam and Clinac iX were found in in‐air profiles and open field output. Maximum depth dose for the TrueBeam Stx and Clinac iX for the following energies (6, 9, 12, 16, 20 MeV) are respectively (1.15; 1.89; 2.6; 3.1; and 2.35) and (1.24; 1.95; 2.70; 2.99 and 2.4cm). For the TrueBeam Stx and Clinac iX the quality index R50 for applicator 15x15 cm2 are in the tolerance intervals. Surface dose increases by increasing energy for both machines. The Absolute Dose (cGy/MU) calibrated for both machine in Dmax at 1cGy/MU for the reference field size cone 15x15 cm2. Bremsstrahlung tail Rp per energy levels as follows for the TrueBeam Stx : 6 MeV – 2.85 cm, 9 MeV – 4.28 cm, 12 MeV – 5.97 cm, 16 MeV – 7.88 cm and 20 MeV – 9.86 cm. and for the Clinac iX : 6 MeV – 2.86 cm, 9 MeV – 4.32 cm, 12 MeV – 5.96 cm, 16 MeV – 7.93 cm and 20 MeV – 10.08 cm. A good agreement between modeled and measured data is observed.

scholarly journals Dosimetric Characterization of Small Radiotherapy Electron Beams Collimated by Circular Applicators with the New Microsilicon Detector

2022 ◽  
Vol 12 (2) ◽  
pp. 600
Author(s):  
Serenella Russo ◽  
Silvia Bettarini ◽  
Barbara Grilli Leonulli ◽  
Marco Esposito ◽  
Paolo Alpi ◽  
...  
Keyword(s):  
Radiation Therapy ◽  
Electron Beams ◽  
High Energy ◽  
Field Size ◽  
The Novel ◽  
Linear Accelerators ◽  
Depth Dose ◽  
Dosimetric Data ◽  
Output Factors ◽  
Dose Measurements

High-energy small electron beams, generated by linear accelerators, are used for radiotherapy of localized superficial tumours. The aim of the present study is to assess the dosimetric performance under small radiation therapy electron beams of the novel PTW microSilicon detector compared to other available dosimeters. Relative dose measurements of circular fields with 20, 30, 40, and 50 mm aperture diameters were performed for electron beams generated by an Elekta Synergy linac, with energy between 4 and 12 MeV. Percentage depth dose, transverse profiles, and output factors, normalized to the 10 × 10 cm2 reference field, were measured. All dosimetric data were collected in a PTW MP3 motorized water phantom, at SSD of 100 cm, by using the novel PTW microSilicon detector. The PTW diode E and the PTW microDiamond were also used in all beam apertures for benchmarking. Data for the biggest field size were also measured by the PTW Advanced Markus ionization chamber. Measurements performed by the microSilicon are in good agreement with the reference values for all the tubular applicators and beam energies within the stated uncertainties. This confirms the reliability of the microSilicon detector for relative dosimetry of small radiation therapy electron beams collimated by circular applicators.

scholarly journals Improving Clinical dosimetric Accuracy of cancer treatment using a special quality of Electron and Photon Beam

2021 ◽  
Vol 5 (3) ◽  
Author(s):  
Ayesha Ikhlaq ◽  
Saeed Ahmad Buzdar ◽  
Muhammad Usman Mustafa ◽  
Sana Salahuddin ◽  
Mehr-Un-Nisa ◽  
...  
Keyword(s):  
Radiation Therapy ◽  
Electron Beam ◽  
Electron Beams ◽  
Photon Beam ◽  
Field Size ◽  
External Beam Radiation ◽  
Photon Beams ◽  
Depth Dose ◽  
Electron And Photon

In external beam radiation therapy, electron and photon beams have extraordinary characteristics in the treatment of cancer. The electron and photon beam characteristic are essential to study before calibration of machine. This study focused on the dosimetric characteristics of different energies of electron beams for different field size. The basic objective of this work is, to calculate dosimetric parameters and characteristics of electron beam, specially depth dose characteristics along central axis. In this work, 6 MeV, 9 MeV, 12 MeV, 15 MeV and 18 MeV of electron beam and 6 MV and 15 MV of photon beam with different field size is used. Characteristics of depth dose of electron and photon beam in water have analyzed to provide better quality of radiation therapy treatment planning. The different beam characteristics are due to different interactions that occurs between electron beams giving them a definite range whereas photon beams are attenuated leading to dose deposition and much larger range with no definite end. Depth dose characteristics of electron and photon beams do not show same characteristics as interaction of beam with matter depends on the quality of beam. Attenuation and penetration factors change with changing dosimetric parameters. Complete analysis of dosimetric characteristics of electron and photon beam help to choose more accurate beam for the treatment of cancer. This work will help to increase accuracy in treatment of cancer with radiotherapy.

scholarly journals Dosimetric Characterization of Small Radiation Therapy Electron Beams Collimated by Tubular Applicators With the New Micro-Silicon Detector

2021 ◽  
Author(s):  
Serenella Russo ◽  
Silvia Bettarini ◽  
Barbara Grilli Leonulli ◽  
Marco Esposito ◽  
Paolo Alpi ◽  
...  
Keyword(s):  
Radiation Therapy ◽  
Electron Beams ◽  
Silicon Detector ◽  
High Energy ◽  
Field Size ◽  
The Novel ◽  
Linear Accelerators ◽  
Depth Dose ◽  
Dosimetric Data ◽  
Output Factors

High-energy small electron beams generated by linear accelerators are used for radiotherapy of localized superficial tumors. The aim of the present study is to assess the dosimetric performance under small radiation therapy electron beams of the novel PTW microSilicon detector by comparison with commercially available dosimeters. Relative dose measurements of circular fields with 20, 30, 40 and 50 mm aperture diameters were performed for 4 to 12 MeV energy range of electron beams generated by an Elekta Synergy linac. Percentage depth dose, transverse profiles and output factors normalized to the 10 × 10 cm2 reference field were measured. All dosimetric data were collected in a PTW MP3 motorized water phantom at SSD of 100cm by using the novel PTW microSilicon detector. The PTW diode E and the PTW microDiamond were also used in all beam aperture for benchmarking. Data for the biggest field size were also measured by the PTW Advanced Markus ionization chamber.Measurements performed by the microSilicon are in good agreement with the reference values for all the tubular applicators and beam energies, within the stated uncertainties. This confirms the reliability of the microSilicon detector for relative dosimetry of small radiation therapy electron beams collimated by tubular applicators.

scholarly journals Benchmarking of Siemens Linac in Electron Modes: 8-14 MeV Electron Beams

2018 ◽  
Vol 8 (2) ◽  
Author(s):  
H Dowlatabadi ◽  
A A Mowlavi ◽  
M Ghorbani ◽  
S Mohammadi ◽  
F Akbari
Keyword(s):  
Monte Carlo ◽  
Radiation Treatment ◽  
Electron Beams ◽  
Dose Profile ◽  
Depth Dose ◽  
Mcnpx Code ◽  
Gamma Index ◽  
Simulation Results ◽  
Mc Simulation ◽  
Good Agreement

Introduction: Radiation therapy using electron beams is a promising method due to its physical dose distribution. Monte Carlo (MC) code is the best and most accurate technique for forespeaking the distribution of dose in radiation treatment of patients.Materials and Methods: We report an MC simulation of a linac head and depth dose on central axis, along with profile calculations. The purpose of the present research is to carefully analyze the application of MC methods for the calculation of dosimetric parameters for electron beams with energies of 8–14 MeV at a Siemens Primus linac. The principal components of the linac head were simulated using MCNPX code for different applicators. Results: The consequences of measurements and simulations revealed a good agreement. Gamma index values were below 1 for most points, for all energy values and all applicators in percent depth dose and dose profile computations. A number of states exhibited rather large gamma indices; these points were located at the tail of the percent depth dose graph; these points were less used in in radiotherapy. In the dose profile graph, gamma indices of most parts were below 1. The discrepancies between the simulation results and measurements in terms of Zmax, R90, R80 and R50 were insignificant. The results of Monte Carlo simulations showed a good agreement with the measurements. Conclusion: The software can be used for simulating electron modes of a Siemens Primus linac when direct experimental measurements are not feasible.

Dosimetric evaluation of a novel electron–photon mixed beam, produced by a medical linear accelerator

2018 ◽  
Vol 17 (3) ◽  
pp. 319-331
Author(s):  
Navid Khaledi ◽  
Dariush Sardari ◽  
Mohammad Mohammadi ◽  
Ahmad Ameri ◽  
Nick Reynaert
Keyword(s):  
Electron Beams ◽  
High Energy ◽  
Primary Electron ◽  
Linear Accelerators ◽  
Ion Chamber ◽  
Depth Dose ◽  
Mixed Beam ◽  
Small Fields ◽  
Lead Layer ◽  
Electron Photon

AbstractAimThis study deals with the characteristics of simultaneous photon and electron beams in homogenous and inhomogeneous phantoms by experimental and Monte Carlo dosimetry, for therapeutic purposes. Materials and methods: Both 16 and 20 MeV high-energy electron beams were used as the original beam to strike perforated lead sheets to produce the mixed beam. The dosimetry results were achieved by measurement in an ion chamber in a water phantom and film dosimetry in a Perspex nasal phantom, and then compared with those calculated through a simulation approach. To evaluate two-dimensional dose distribution in the inhomogeneous medium, the dose–area histogram was obtained.ResultsThe highest percentage of photon contribution in mixed beam was found to be 36% for 2-mm thickness of lead layer with holes diameter of 0·2 cm for a 20 MeV primary electron energy. For small fields, the percentage depth dose parameters variations were found to be similar to pure electron beam within ±2%. The most feasible flatness in beam profile was 11% for pure electron and 7% for the mixed beam. Penumbra changes as function of depth was about ten times better than in pure electron field.ConclusionsThe results present some dosimetric advantages that can make this study a platform for the production of simultaneous mixed beams in future linear accelerators (LINACs), which through redesign of the LINAC head, which could lead to setup error reduction and a decrease of intra-fractional tumour cells repair.

scholarly journals Grid Monte Carlo Simulation of a Medical Linear Accelerator

2018 ◽  
Vol 3 (12) ◽  
pp. 40-43 ◽  
Author(s):  
Didi Samir ◽  
Mustapha Zerfaoui ◽  
Abdelilah Moussa ◽  
Yassine Benkhouya ◽  
Mehdi El Ouartiti
Keyword(s):  
Monte Carlo ◽  
Linear Accelerator ◽  
Field Size ◽  
Dose Profile ◽  
Depth Dose ◽  
Grid Simulation ◽  
Medical Linear Accelerator ◽  
Measured Dose ◽  
Better Than ◽  
Good Agreement

A full grid simulation of the head of an Elekta Synergy Platform medical linear accelerator is performed using the Geant4 Monte Carlo platform. The simulation includes all components of the accelerator head and a homogeneous water phantom. Results in terms of depth doses and lateral dose profiles are presented for 6 MV photon beam with the 10x10 cm2 reference field size at 100 cm distance from the source. Overall, a good agreement with the measured dose data is achieved with a precision better than 0.93% and 2.63% for the depth dose profile and lateral dose profiles respectively.

scholarly journals Evaluation of some dosimetric properties of a dedicated plane parallel ionization chamber for radiotherapy electron beams

2018 ◽  
Vol 6 (3) ◽  
Author(s):  
Jonas Oliveira da Silva ◽  
Fernanda Beatrice Conceição Nonato ◽  
Francisco Glaildo Almeida Sampaio ◽  
Linda V. Ehlin Caldas
Keyword(s):  
Electron Beam ◽  
Ionization Chamber ◽  
Electron Beams ◽  
International Standards ◽  
Field Size ◽  
Guard Ring ◽  
Sensitive Volume ◽  
Plane Parallel ◽  
Nail Polish ◽  
Beam Dosimetry

Ionization chambers are the reference detectors for electron beam dosimetry. In this paper a dedicated radiotherapy plane parallel ionization chamber manufactured with low cost materials is presented for dosimetry in electron beams. The ionization chamber tested has a sensitive volume of 0.4 cm³, and the collecting electrode and the guard ring were painted with a homogeneous mixture of nail polish and graphite. The dedicated ionization chamber presented linearity of the response with the absorbed dose in the range of 0.5 Gy to 8.0 Gy, an increase of the response with the field size increasing, an angular dependence within ±5°, as recommended by international standards, and a polarity effect of 0.78% with the field size. From the results obtained, it is possible to conclude that the plane parallel ionization chamber tested in this work presents potential use for electron beam dosimetry in clinical routine.

scholarly journals Feasibility studies of using thin entrance window photodiodes for clinical electron beam dosimetry

2019 ◽  
Vol 7 (2A) ◽  
Author(s):  
Cristina R. Nascimento ◽  
Viviane K. Asfora ◽  
Vinicius R. M. Barros ◽  
Josemary A. C. Gonçalves ◽  
Luiza F. R. Andrade ◽  
...  
Keyword(s):  
Electron Beam ◽  
Ionization Chamber ◽  
Electron Beams ◽  
Beam Quality ◽  
Absorbed Dose ◽  
Feasibility Studies ◽  
Entrance Window ◽  
Sensitive Volume ◽  
Depth Dose ◽  
Beam Dosimetry

The response of the commercial XRA-24 PIN photodiode (5.76 mm2 active area) for clinical electron beam dosimetry covering the range of 8-12 MeV was investigated. Within this energy range, the charge generated in the diode’s sensitive volume is linearly dependent on the absorbed dose up to 320 cGy.  However, charge sensitivity coefficients evidenced that the dose response of the diode is slightly dependent on the electron beam energy. Indeed, the diode’s energy dependence was within 8.5% for 8-12MeV electron beams. On the other hand, it was also observed an excellent repeatability of these results with a variation coefficient (VC) lower than 0.4%, which is within the 1% tolerance limit recommended by the AAPM TG-62. Furthermore, the agreement between the percentage depth dose profiles (PDD) gathered with the diode and the ionization chamber allowed achieving the electron beam quality within 1% of that obtained with the ionization chamber. Based on these results, the photodiode XRA-24 can be a reliable and inexpensive alternative for electron beams dosimetry.

Sign in / Sign up

Export Citation Format

Share Document