Position Control Strategy and Experimental Research of A 2R Underactuated Planar Flexible Manipulator

2013 ◽  
Vol 49 (23) ◽  
pp. 80 ◽  
Author(s):  
Wei CHEN
2021 ◽  
Vol 10 (1) ◽  
pp. 43
Author(s):  
Fattah Hanafi Sheikhha ◽  
Ali Afzalaghaeinaeini ◽  
Jaho Seo

A hydraulic excavator consists of multiple electrohydraulic actuators (EHA). Due to uncertainties and nonlinearities in EHAs, it is challenging to devise a proper control strategy. To tackle this issue, a major goal of our study is to provide an efficient control strategy to minimize tracking errors of the bucket tip position for autonomous excavation. To accomplish the goal, the study offers a collaboration of PID and fuzzy controllers that are used to compensate for contour errors and achieve accurate actuator position control, respectively. Co-simulation models including control algorithms and hydraulic components were created using Matlab and Amesim to validate the performance of the designed controllers. Simulations indicate that the proposed method enables achieving accurate tracking control for autonomous excavation with small tracking errors despite the nonlinear characteristics of the hydraulic excavator system.


2020 ◽  
Vol 9 (2) ◽  
pp. 155-168
Author(s):  
Ziwang Lu ◽  
◽  
Guangyu Tian ◽  

Torque interruption and shift jerk are the two main issues that occur during the gear-shifting process of electric-driven mechanical transmission. Herein, a time-optimal coordination control strategy between the the drive motor and the shift motor is proposed to eliminate the impacts between the sleeve and the gear ring. To determine the optimal control law, first, a gear-shifting dynamic model is constructed to capture the drive motor and shift motor dynamics. Next, the time-optimal dual synchronization control for the drive motor and the time-optimal position control for the shift motor are designed. Moreover, a switched control for the shift motor between a bang-off-bang control and a receding horizon control (RHC) law is derived to match the time-optimal dual synchronization control strategy of the drive motor. Finally, two case studies are conducted to validate the bang-off-bang control and RHC. In addition, the method to obtain the appropriate parameters of the drive motor and shift motor is analyzed according to the coordination control method.


Author(s):  
Joseph Bowkett ◽  
Rudranarayan Mukherjee

While the majority of terrestrial multi-link manipulators can be considered in a purely kinematic sense due to their high stiffness, the launch mass restrictions of aerospace applications such as in-orbit assembly of large space structures result in low stiffness links being employed, meaning dynamics can no longer be ignored. This paper seeks to investigate the suitability of several different open and closed loop control techniques for application to the problem of end effector position control with minimal vibration for a low stiffness space based manipulator. Simulations of a representative planar problem with two flexible links are used to measure performance and sensitivity to parameter variation of: model predictive control, command shaping, and command shaping with linear quadratic regulator (LQR) feedback. An experimental testbed is then used to validate simulation results for the recommended command shaped controller.


1990 ◽  
Vol 112 (4) ◽  
pp. 734-739 ◽  
Author(s):  
Jiing-Yih Lai ◽  
Chia-Hsiang Menq ◽  
Rajendra Singh

We propose a new control strategy for on-off valve controlled pneumatic actuators and robots with focus on the position accuracy. A mathematical model incorporating pneumatic process nonlinearities and nonlinear mechanical friction has been developed to characterize the actuator dynamics; this model with a few simplifications is then used to design the controller. In our control scheme, one valve is held open and the other is operated under the pulse width modulation mode to simulate the proportional control. An inner loop utilizing proportional-plus-integral control is formed to control the actuator pressure, and an outer loop with displacement and velocity feedbacks is used to control the load displacement. Also, a two staged feedforward force is implemented to reduce the steady state error due to the nonlinear mechanical friction. Experimental results on a single-degree-of-freedom pneumatic robot indicate that the proposed control system is better than the conventional on-off control strategy as it is effective in achieving the desired position accuracy without using any mechanical stops in the actuator.


2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Lizheng Pan ◽  
Aiguo Song ◽  
Suolin Duan ◽  
Zhuqing Yu

Safety is one of the crucial issues for robot-aided neurorehabilitation exercise. When it comes to the passive rehabilitation training for stroke patients, the existing control strategies are usually just based on position control to carry out the training, and the patient is out of the controller. However, to some extent, the patient should be taken as a “cooperator” of the training activity, and the movement speed and range of the training movement should be dynamically regulated according to the internal or external state of the subject, just as what the therapist does in clinical therapy. This research presents a novel motion control strategy for patient-centered robot-aided passive neurorehabilitation exercise from the point of the safety. The safety-motion decision-making mechanism is developed to online observe and assess the physical state of training impaired-limb and motion performances and regulate the training parameters (motion speed and training rage), ensuring the safety of the supplied rehabilitation exercise. Meanwhile, position-based impedance control is employed to realize the trajectory tracking motion with interactive compliance. Functional experiments and clinical experiments are investigated with a healthy adult and four recruited stroke patients, respectively. The two types of experimental results demonstrate that the suggested control strategy not only serves with safety-motion training but also presents rehabilitation efficacy.


2014 ◽  
Vol 5 (3) ◽  
pp. 25-48
Author(s):  
Girish Sriram ◽  
Alex Jensen ◽  
Steve C. Chiu

The human hand along with its fingers possess one of the highest numbers of nerve endings in the human body. It thus has the capacity for the richest tactile feedback for positioning capabilities. This article shares a new technique of controlling slippage. The sensing system used for the detection of slippage is a modified force sensing resistor (FSR®). The control system is a fuzzy logic control algorithm with multiple rules that is designed to be processed on a mobile handheld computing platform and integrated/working alongside a traditional Electromyography (EMG) or Electroencephalography (EEG) based control system used for determining position of the fingers. A 5 Degrees of Freedom (DOF) hand, was used to test the slippage control strategy in real time. First a reference EMG signal was used for getting the 5 DOF hand to grasp an object, using position control. Then a slip was introduced to see the slippage control strategy at work. The results based on the plain tactile sensory feedback and the modified sensory feedback are discussed.


2019 ◽  
Vol 103 (1) ◽  
pp. 003685041988646
Author(s):  
Weicun Zhang ◽  
Qing Li ◽  
Yuzhen Zhang ◽  
Ziyi Lu ◽  
Cheng Nian

In this article, a weighted multiple model adaptive boundary control scheme is proposed for a flexible manipulator with unknown large parameter uncertainties. First, the uncertainties are approximatively covered by a finite number of constant models. Second, based on Euler–Bernoulli beam theory and Hamilton principle, the distributed parameter model of the flexible manipulator is constructed in terms of partial differential equation for each local constant model. Correspondingly, local boundary controllers are designed to control the manipulator movement and suppress its vibration for each partial differential equation model, which are based on Lyapunov stability theory. Then, a novel weighted multiple model adaptive control strategy is developed based on an improved weighting algorithm. The stability of the overall closed-loop system is ensured by virtual equivalent system theory. Finally, numerical simulations are provided to illustrate the feasibility and effectiveness of the proposed control strategy.


2011 ◽  
Vol 317-319 ◽  
pp. 1490-1494 ◽  
Author(s):  
Bao Quan Jin ◽  
Yan Kun Wang ◽  
Ya Li Ma

The parameters uncertainty and external disturbance play a negative role to improve electro-hydraulic position servo system performance. The valve controlled cylinder system model is established, using the traditional PID control strategy and reaching law control strategy for simulating the system, respectively, the two methods have similar control effects in the ideal model, but considering the external disturbances, the index approaches sliding mode control law has better response speed and stability. Research shown that sliding mode control algorithm has an important role for improving the performance of hydraulic servo position control system.


Sign in / Sign up

Export Citation Format

Share Document