Oil Palm Bio-Fiber Reinforced Thermoplastic Composites-Effects of Matrix Modification on Mechanical and Thermal Properties

2010 ◽  
Vol 10 (24) ◽  
pp. 3271-3276 ◽  
Author(s):  
S.S. Suradi ◽  
R.M. Yunus ◽  
M.D.H. Beg ◽  
M. Rivai ◽  
Z.A.M. Yusof
Keyword(s):  
Thermal Properties ◽  
Oil Palm ◽  
Thermoplastic Composites ◽  
Mechanical And Thermal Properties ◽  
Fiber Reinforced ◽  
Matrix Modification

scholarly journals Enhanced Mechanical and Thermal Properties of Modified Oil Palm Fiber-Reinforced Polypropylene Composite via Multi-Objective Optimization of In Situ Silica Sol-Gel Synthesis

Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3338
Author(s):  
Nasrullah Mat Rozi ◽  
Hamidah Abdul Hamid ◽  
Md. Sohrab Hossain ◽  
Nor Afifah Khalil ◽  
Ahmad Naim Ahmad Yahaya ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Oil Palm ◽  
Sol Gel ◽  
Silica Sol ◽  
Mechanical And Thermal Properties ◽  
Fiber Reinforced ◽  
Palm Fiber ◽  
In Situ Silica ◽  
Sol Gel Process

A multi-objective optimization of in situ sol-gel process was conducted in preparing oil palm fiber-reinforced polypropylene (OPF-PP) composite for an enhancement of mechanical and thermal properties. Tetraethyl orthosilicate (TEOS) and butylamine were used as precursors and catalysts for the sol-gel process. The face-centered central composite design (FCCD) experiments coupled with response surface methodology (RSM) has been utilized to optimize in situ silica sol-gel process. The optimization process showed that the drying time after the in-situ silica sol-gel process was the most influential factor on silica content, while the molar ratio of TEOS to water gave the most significant effect on silica residue. The maximum silica content of 34.1% and the silica residue of 35.9% were achieved under optimum conditions of 21.3 h soaking time, 50 min drying time, pH value of 9.26, and 1:4 molar ratio of TEOS to water. The untreated oil palm fiber (OPF) and silica sol-gel modified OPF (SiO2-OPF) were used as the reinforcing fibers, with PP as a matrix and maleic anhydride grafted polypropylene (MAgPP) as a compatibilizer for the fiber-reinforced PP matrix (SiO2-OPF-PP-MAgPP) composites preparation. The mechanical and thermal properties of OPF-PP, SiO2-OPF-PP, SiO2-OPF-PP-MAgPP composites, and pure PP were determined. It was found that the OPF-S-PP-MAgPP composite had the highest toughness and stiffness with values of tensile strength, Young’s modulus, and elongation at break of 30.9 MPa, 881.8 MPa, and 15.1%, respectively. The thermal properties analyses revealed that the OPF-S-PP-MAgPP exhibited the highest thermally stable inflection point at 477 °C as compared to pure PP and other composites formulations. The finding of the present study showed that the SiO2-OPF had the potential to use as a reinforcing agent to enhance the thermal-mechanical properties of the composites.

scholarly journals Effect of Organo-Modified Montmorillonite Nanoclay on Mechanical, Thermo-Mechanical, and Thermal Properties of Carbon Fiber-Reinforced Phenolic Composites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 754
Author(s):  
Jantrawan Pumchusak ◽  
Nonthawat Thajina ◽  
Watcharakorn Keawsujai ◽  
Pattarakamon Chaiwan
Keyword(s):  
Thermal Properties ◽  
Carbon Fiber ◽  
Bending Strength ◽  
Mechanical And Thermal Properties ◽  
Fiber Reinforced ◽  
Heat Resistant ◽  
Degradation Temperature ◽  
Modified Montmorillonite ◽  
Carbon Fiber Reinforced ◽  
Montmorillonite Nanoclay

This work aims to explore the effect of organo-modified montmorillonite nanoclay (O-MMT) on the mechanical, thermo-mechanical, and thermal properties of carbon fiber-reinforced phenolic composites (CFRP). CFRP at variable O-MMT contents (from 0 to 2.5 wt%) were prepared. The addition of 1.5 wt% O-MMT was found to give the heat resistant polymer composite optimum properties. Compared to the CFRP, the CFRP with 1.5 wt% O-MMT provided a higher tensile strength of 64 MPa (+20%), higher impact strength of 49 kJ/m2 (+51%), but a little lower bending strength of 162 MPa (−1%). The composite showed a 64% higher storage modulus at 30 °C of 6.4 GPa. It also could reserve its high modulus up to 145 °C. Moreover, it had a higher heat deflection temperature of 152 °C (+1%) and a higher thermal degradation temperature of 630 °C. This composite could maintain its mechanical properties at high temperature and was a good candidate for heat resistant material.

scholarly journals Thermal Shock Behavior of Twill Woven Carbon Fiber Reinforced Polymer Composites

2021 ◽  
Vol 5 (1) ◽  
pp. 33
Author(s):  
Farzin Azimpour-Shishevan ◽  
Hamit Akbulut ◽  
M.A. Mohtadi-Bonab
Keyword(s):  
Thermal Properties ◽  
Carbon Fiber ◽  
Thermal Cycling ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Mechanical And Thermal Properties ◽  
Fiber Reinforced ◽  
Cycling Process ◽  
Reinforced Polymer ◽  
Thermal Cycling Process

In the current research, the effect of cyclic temperature variation on the mechanical and thermal properties of woven carbon-fiber-reinforced polymer (CFRP) composites was investigated. To this, carbon fiber textiles in twill 2/2 pattern were used as reinforced phase in epoxy, and CFRPs were fabricated by vacuum-assisted resin-infusion molding (VARIM) method. Thermal cycling process was carried out between −40 and +120 °C for 20, 40, 60 and 80 cycles, in order to evaluate the effect of thermal cycling on mechanical and thermal properties of CFRP specimens. In this regard, tensile, bending and short beam shear (SBS) experiments were carried out, to obtain modulus of elasticity, tensile strength, flexural modulus, flexural strength and inter-laminar shear strength (ILSS) at room temperature (RT), and then thermal treated composites were compared. A dynamic mechanical analysis (DMA) test was carried out to obtain thermal properties, and viscoelastic properties, such as storage modulus (E’), loss modulus (E”) and loss factors (tan δ), were evaluated. It was observed that the characteristics of composites were affected by thermal cycling due to post-curing at a high temperature. This process worked to crosslink and improve the composite behavior or degrade it due to the different coefficients of thermal expansion (CTEs) of composite components. The response of composites to the thermal cycling process was determined by the interaction of these phenomena. Based on SEM observations, the delamination, fiber pull-out and bundle breakage were the dominant fracture modes in tensile-tested specimens.

Sign in / Sign up

Export Citation Format

Share Document