scholarly journals Influence of sintering conditions on translucency, biaxial flexural strength, microstructure, and low-temperature degradation of highly translucent dental zirconia

2021 ◽  
Author(s):  
Thaw Di CHO TOO ◽  
Masanao INOKOSHI ◽  
Kosuke NOZAKI ◽  
Makoto SHIMIZUBATA ◽  
Hiroto NAKAI ◽  
...  
Keyword(s):  
Low Temperature ◽  
Flexural Strength ◽  
Biaxial Flexural Strength ◽  
Sintering Conditions

scholarly journals Effect of Different Surface Treatments on Biaxial Flexural Strength of Yttria-stabilized Tetragonal Zirconia Polycrystal

2018 ◽  
Vol 19 (3) ◽  
pp. 318-323
Author(s):  
Teerthesh Jain ◽  
Amit Porwal ◽  
Sumanth Babu ◽  
Zahid A Khan ◽  
Chandeep Kaur ◽  
...  
Keyword(s):  
Low Temperature ◽  
Flexural Strength ◽  
Tetragonal Zirconia ◽  
Surface Treatments ◽  
Control Group ◽  
Significant Difference ◽  
Biaxial Flexural Strength ◽  
Computer Aided ◽  
The Impact ◽  
Tetragonal Zirconia Polycrystal

ABSTRACT Introduction Ceramics are widely applied in dentistry owing to their excellent mechanical and physical attributes. The most popular ceramics are Lava™, KaVo Everest, and Cercon. However, it is unclear whether or not a different surface treatment along with low-temperature aging and mechanical loading (ML) affects the physical properties of computer-aided design (CAD)/computer-aided manufacturing (CAM)-machined yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic. Aim The objective of this research was to assess the impact of various surface treatments as air-particle abrasion, ML, low-temperature degradation (LTD), and their cumulative effects on biaxial flexural properties of Y-TZP. Materials and methods Totally, 50 specimens were fabricated by CAD–CAM machining from Cercon® and divided into five groups following different surface treatments as control (C), air-particle abrasion (Si), ML, LTD, and cumulative treatment (CT) group. Results were investigated by two-way analysis of variance (ANOVA) and Tukey honest significant difference (HSD) test. Results The highest biaxial flexural strength was observed in the Si group (950.2 ± 126.7 MPa), followed by the LTD group (861.3 ± 166.8 MPa), CT group (851.2 ± 126.5 MPa), and the least with ML (820 ± 110 MPa). A significant difference was observed in the two-way ANOVA test. X-ray diffraction (XRD) analysis showed that the control group consists of 100% tetragonal zirconia and the maximum amount of monoclinic phase was obtained after LTD. Conclusion No negative effect on biaxial flexural strength was observed; indeed, it increases the biaxial strength. Hence, these surface treatments can be done in routine clinical practice to improve the performance of ceramic restoration. How to cite this article Jain T, Porwal A, Babu S, Khan ZA, Kaur C, Jain RB. Effect of Different Surface Treatments on Biaxial Flexural Strength of Yttria-stabilized Tetragonal Zirconia Polycrystal. J Contemp Dent Pract 2018;19(3):318-323.

Impact of Silane-containing Universal Adhesive on the Biaxial Flexural Strength of a Resin Cement/Glass-ceramic System

2019 ◽  
Vol 44 (2) ◽  
pp. 200-209 ◽  
Author(s):  
F Murillo-Gómez ◽  
RB Wanderley ◽  
MF De Goes
Keyword(s):  
Flexural Strength ◽  
Glass Ceramic ◽  
Resin Cement ◽  
Weibull Analysis ◽  
Ceramic System ◽  
Universal Adhesive ◽  
Bonded Interface ◽  
Biaxial Flexural Strength ◽  
Digital Caliper ◽  
One Way Anova

SUMMARY The aim of this study was to determine whether using a silane-containing universal adhesive as a silane primer in glass-ceramic/resin cement systems affects biaxial flexural strength (BFS) and bonded interface integrity after loading. Glass-ceramic (IPS e.max CAD, Ivoclar/Vivadent, Schaan, Liechtenstein) disc-shaped specimens (6.5±0.1mm in diameter, 0.5±0.1mm thick) were etched with 5% hydrofluoric acid (HF) for 20 seconds and divided into four groups of 30 specimens, to be treated as follows: 1) One bottle silane primer (RCP); 2) Separate application of silane and adhesive (RCP+SB); 3) Silane-containing universal adhesive (SBU); 4) No treatment (C). After silanization, all specimens were resin cement– coated and polymerized for 40 seconds. Each specimen layer was measured, as well as each assembly's thickness, using a digital caliper and scanning electron microscope (SEM). Specimens were stored for 24 hours and submitted to a BFS test (1.27 mm/min). BFS values were calculated using the bilayer disc-specimen solution. Bonded interfaces were analyzed on fractured fragments using SEM. One-way ANOVA and Tukey tests (α=0.05) were applied, as well as the Weibull analysis. Factor “silane treatment” was statistically significant (p<0.0001). RCP+SB (372.2±29.4 MPa) and RCP (364.2±29.5 MPa) produced significantly higher BFS than did the C (320.7±36.3 MPa) or SBU (338.0±27.1 MPa) groups. No differences were found in the Weibull modulus (m: RCP: 10.1-17.3; RCP+SB: 10.1-17.0; SBU: 12.3-22.4; C: 7.4-12.9). Bonded interface analysis exhibited ceramic-cement separation (SBU, C) and voids within the resin cement layer (all groups). Neither the ceramic/cement system's BFS nor its bonded interface stability were improved by SBU after loading.

Ag diffusion inhibition and enhanced flexural strength in low temperature co-fired CaO-Al2O3-B2O3-SiO2 glasses

2019 ◽  
Vol 782 ◽  
pp. 1094-1102 ◽  
Author(s):  
Kuei-Chih Feng ◽  
Pin-Yi Chen ◽  
Chi-Shun Tu ◽  
Cheng-Sao Chen ◽  
R.R. Chien ◽  
...  
Keyword(s):  
Low Temperature ◽  
Flexural Strength

Effects of artificial aging on the biaxial flexural strength of Ce-TZP/Al2O3 and Y-TZP after various occlusal adjustments

2017 ◽  
Vol 43 (13) ◽  
pp. 9951-9959 ◽  
Author(s):  
Il-Gwang Sim ◽  
Yooseok Shin ◽  
June-Sung Shim ◽  
Jong-Eun Kim ◽  
Jee-Hwan Kim
Keyword(s):  
Flexural Strength ◽  
Artificial Aging ◽  
Biaxial Flexural Strength

scholarly journals Effect of light sources and curing mode techniques on sorption, solubility and biaxial flexural strength of a composite resin

2012 ◽  
Vol 20 (2) ◽  
pp. 246-252 ◽  
Author(s):  
Andreia Assis Carvalho ◽  
Francine do Couto Lima Moreira ◽  
Rodrigo Borges Fonseca ◽  
Carlos José Soares ◽  
Eduardo Batista Franco ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Composite Resin ◽  
Light Sources ◽  
Biaxial Flexural Strength ◽  
Effect Of Light

scholarly journals Biaxial flexural strength of different types of monolithic zirconia

2019 ◽  
Vol 22 (1) ◽  
pp. Process
Author(s):  
Shereen Ahmed Nossair ◽  
Tarek Salah ◽  
Kamal Khaled Ebeid
Keyword(s):  
Flexural Strength ◽  
Zirconia Ceramic ◽  
Group 4 ◽  
Dental Esthetics ◽  
Biaxial Flexural Strength ◽  
Different Types ◽  
Monolithic Zirconia ◽  
Group 5 ◽  
Group 2 ◽  
Post Hoc

Objective: This study was designed to evaluate the biaxial flexural strength (BFS) of different types of unshaded and shaded monolithic zirconia. Material and Methods: 120 monolithic zirconia ceramic discs were fabricated. They were divided into twelve groups (n=10), Group 1; Bruxzir unshaded, Group 2; Bruxzir shaded A2, Group 3; Bruxzir anterior white, Group 4; Bruxzir anterior shade A2, Group 5; Prettau unshaded, Group 6; Prettau shaded with A2 coloring liquid, Group 7; Prettau anterior white, Group 8; Prettau anterior shaded with A2 coloring liquid, Group 9; Katana HT white, Group 10; Katana HT shade A2, Group 11; Katana ST white, Group 12; Katana ST shade A2. All discs were milled using a dental milling machine, and had final dimensions after sintering of 15 mm diameter and 1 mm thickness. BFS was tested using piston on three ball technique. Results:  One-way ANOVA revealed significant differences among the 12 groups. Tukey post-hoc tests revealed no significant differences between the groups 3, 4, ,7 ,8 11, and 12. However, they all had BFS values that are significantly lower than all other groups. Group 2 showed statistically significant higher BFS values when compared to group 3,4, 7, 8, 11, and 12 while it showed statistically significant lower values when compared to groups 1, 5, 6, 9, and 10. Conclusion: Increase in the yttria content in zirconia led to a decrease in its BFS. Shading of zirconia did not have a significant effect on the final strength of zirconia. KeywordsDental ceramics; Dental esthetics; Flexural strength; Shaded zirconia. 

Sign in / Sign up

Export Citation Format

Share Document