Optimisation of Machining Parameters in Electrical Discharge Machining of LM25-RHA Composites

2017 ◽  
pp. 1-18
Author(s):  
Srikant Tiwari ◽  
Mohan Kumar Pradhan
Keyword(s):  
Conventional Method ◽  
Rice Husk ◽  
Electrical Discharge ◽  
Rice Husk Ash ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Optimal Setting

Aluminium composites are tough to machine by using conventional method. In order to increase machinability of aluminium-based composite a non-conventional method of machining has been used. Electrical Discharge Machining (EDM) is one of the kind of machining process which has often uses for machining of aluminium composites. The objective of this chapter is to determine the ideal setting of the process parameters on the electrical discharge machining while machining Aluminium-Rice Husk Ash (LM25-RHA) composites in which three different variation (4%, 8%, 12%) of Rice Husk Ash has been used. The parameters considered are pulse current (Ip), gap voltage (V) and pulse-on-time (Ton); whereas its effect are analysed on Electrode Wear Rate (EWR), Material Removal Rate (MRR) and Surface Roughness (Ra). The optimal setting of the parameters are determined through experiments planned, conducted and analysed using the Taguchi method.

The effect of magnesium content on drilling of Al-Mg-Ti alloy by hole electrical discharge machining process

2020 ◽  
Vol 235 (1-2) ◽  
pp. 125-133
Author(s):  
Omer Eyercioglu ◽  
Kursad Gov
Keyword(s):  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Magnesium Content ◽  
Machining Process ◽  
Electrode Wear ◽  
Ti Alloy ◽  
Ti Alloys ◽  
Mg Content

This study presents an experimental investigation of small hole electrical discharge machining of Al-Mg-Ti alloys. A series of drilling operations were carried out for exploring the effect of magnesium content. Holes of 2 mm diameter and 15 mm depth were drilled using tubular single-hole rotary brass electrodes. The rates of material removal and electrode wear, surface roughness, overcut, average recast layer thickness, taper height and angle were studied for Al-Mg-Ti alloys contain 2%, 4%, 6%, 8%, 10%, 12%, and 14% Mg. The results show that the material removal rate is increasing with increasing Mg content while the rate of electrode wear is almost unchanged. Due to decreasing the melting temperature of the Al-Mg-Ti alloy with increasing Mg content, more metal melts and vaporizes during electrical discharge machining drilling. Therefore, more overcut and taper, thicker white layer, and rougher surfaces were measured for higher Mg content.

scholarly journals Multi-Performance Optimization in Electrical Discharge Machining of Al2O3 Ceramics Using Taguchi Base AHP Weighted TOPSIS Method

Processes ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 1647
Author(s):  
Yue-Peng Zeng ◽  
Chiang-Lung Lin ◽  
Hong-Mei Dai ◽  
Yan-Cherng Lin ◽  
Jung-Chou Hung
Keyword(s):  
Process Parameters ◽  
Performance Optimization ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Statistical Technique ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Relative Closeness ◽  
Machining Parameter

The main application of electrical discharge machining in ceramic processing is limited to conductive ceramics. However, the most commonly used non-conductive potteries in modern industry, such as aluminum oxide (Al2O3), also reveal the limitations of choosing a suitable process. In this study, Taguchi based TOPSIS coupled with AHP weight method to optimize the machining parameters of EDM on Al2O3 leads to better multi-performance. The results showed that the technique is suitable for tackling multi-performance machining parameter optimization. The adhesive foil had a significant impact on material removal rate, electrode wear rate, and surface roughness, according to the findings. In addition, the response graph of relative closeness is used to determine the optimal combination levels of machining parameters. A confirmation test revealed a good agreement between predicted and experimental preference values at an optimum combination of the input parameters. The suggested experimental and statistical technique is a simple, practical, and reliable methodology for optimizing EDM process parameters on Al2O3 ceramics. This approach might be utilized to optimize and improve additional process parameters in the future.

scholarly journals Comparative Study on EDM of Ti-6Al-4V Using Circular and Convex Shaped Electrodes

2018 ◽  
Vol 7 (3.34) ◽  
pp. 256
Author(s):  
S Rajamanickam ◽  
R Palani ◽  
V Sathyamoorthy ◽  
Muppala Jagadeesh Varma ◽  
Shaik Shaik Mahammad Althaf ◽  
...  
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Industrial Applications ◽  
Copper Electrode ◽  
Machining Process ◽  
Project Work ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

As on today, Electrical Discharge Machining (EDM) is world famous unconventional machining process for electrically conductive materials. In this project work, Ti-6Al-4V is performed in electrical discharge machining using differently shaped (circular and convex) copper electrode. The machining parameters considered are the pulse on- time, pulse off-time, voltage and current to investigate machining characteristics like material removal rate and tool wear rate. Taguchi method is applied to frame experimental design. Ti-6Al-4V finds wide usage in industrial applications such as marine, aerospace, bio-medical and so on. 

Evaluation of Electrical Discharge Machining Performance on Al (6351)–SiC–B4C Composite

2019 ◽  
pp. 109-124
Author(s):  
Uthayakumar M. ◽  
Suresh Kumar S. ◽  
Thirumalai Kumaran S. ◽  
Parameswaran P.
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Research Work ◽  
Machining Process ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Machining Performance ◽  
Machined Surface ◽  
Output Performance ◽  
B4c Particles

Electrical discharge machining (EDM) process is a non-conventional machining process used for the material which are difficult to machine. In this research work, an attempt has been made to determine the influence of Boron Carbide (B4C) particles on the machinablity of the Al (6351) alloy reinforced with 5 wt. % Silicon Carbide (SiC) Metal Matrix Composite (MMC) through EDM. Influence of machining parameters such as pulse current (I), pulse on time (Ton), duty factor (τ), and gap voltage (V) on affecting the output performance characteristics namely Electrode Wear Ratio (EWR), Surface Roughness (SR) and Power Consumption (PC) which are studied. The result shows that the addition of B4C particles significantly affects the machinablity of the composite, with a contribution of 1.6% on EWR, 3.5% on SR and 19.8% on PC. The crater, recast layer formation, and Heat Affected Zone (HAZ) in the machined surface of the composite are also reported in detail.

Reducing Electrode Wear Using Cryogenic Cooling during Electrical Discharge Machining

2009 ◽  
Vol 83-86 ◽  
pp. 672-679 ◽  
Author(s):  
Suleiman Abdulkareem ◽  
Ahsan Ali Khan ◽  
Mohamed Konneh
Keyword(s):  
Electrode Material ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Cryogenic Cooling ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Electrode Tool ◽  
Pulse On Time

In electrical discharge machining (EDM), material is removed by a series of electrical discharge between the electrode (tool) and the workpiece that develops a temperature of about 8,0000C to 12,0000C. Due to high temperature of the sparks, work material is melted and vapourized, at the same time the electrode material is also eroded by melting and vapourization. Electrodes wear (EW) process is quite similar to the material removal mechanism as the electrode and the workpiece are considered as a set of electrode in EDM. In the present study effort has been made to reduce EW by cooling, using liquid nitrogen during the EDM of titanium alloy. Investigation on the effect of cooling on electrode wear (EW), material removal rate (MRR) and surface roughness (Ra) of the workpiece was carried out. Current (I), pulse on-time (ton), pause off-time (toff) and voltage (v) were considered as the machining parameters. Design of experiment (DOE) was used to design the experimental works. Cooling of electrode by this technique reduced the melting and vapourization of electrode material and enhances electrode life. It was possible to reduce EW up to 27% by applying this technique while MRR and Ra were improved by 18% and 8% respectively.

The Effect of EDM Die-Sinking Parameters on Material Characteristic for Aluminum Composite

2014 ◽  
Vol 699 ◽  
pp. 26-31 ◽  
Author(s):  
Mohd Amran Ali ◽  
Laily Suraya ◽  
Nor Atiqah Jaffar Sidek ◽  
Nur Izan Syahriah Hussein ◽  
Mohd Razali Muhamad ◽  
...  
Keyword(s):  
Taguchi Method ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Aluminum Composite ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

The machining ability of Electrical Discharge Machining (EDM) die-sinking on material characteristics of LM6 (Al-Sil2) is studied. This is due to the machining process on sharp edge, pocket, deep slot and micro hole cannot be performed by milling and turning machine. The objective of this paper is to determine the relationship between the machining parameters such as pulse on time, pulse off time, peak current and voltage on material removal rate (MRR) that are electrode wear rate (EWR) and surface roughness (Ra). Graphite tool of diameter 15mm was chosen as an electrode. Taguchi method is used as analysis technique to develop experimental matrix that is used to optimize the MRR, EWR and Ra. The analysis was done by using the Minitab software version 16. It is found that the current and pulse off time are significantly effected the MRR, EWR and Ra while pulse on time and voltage are less significant factors that affected the responses. From the Taguchi method, the best setting of optimum value was obtained. Thus, it shows that Taguchi method is the best quality tools that can be applied for production.

scholarly journals Effects of Side Flushing and Multi-Aperture Inner Flushing on Characteristics of Electrical Discharge Machining Macro Deep Holes

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 148
Author(s):  
Suppawat Chuvaree ◽  
Kannachai Kanlayasiri
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Machining Performance ◽  
Electrode Rotation ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

This research investigates the effect of machining parameters on material removal rate, electrode wear ratio, and gap clearance of macro deep holes with a depth-to-diameter ratio over four. The experiments were carried out using electrical discharge machining with side flushing and multi-aperture flushing to improve the machining performance and surface integrity. The machining parameters were pulse on-time, pulse off-time, current, and electrode rotation. Response surface methodology and the desirability function were used to optimize the electrical discharge machining parameters. The results showed that pulse on-time, current, and electrode rotation were positively correlated with the material removal rate. The electrode wear ratio was inversely correlated with pulse on-time and electrode rotation but positively correlated with current. Gap clearance was positively correlated with pulse on-time but inversely correlated with pulse off-time, current, and electrode rotation. The optimal machining condition of electrical discharge machining with side flushing was 100 µs pulse on-time, 20 µs pulse off-time, 15 A current, and 70 rpm electrode rotation; and that of electrical discharge machining with multi-aperture flushing was 130 µs, 2 µs, 15 A, and 70 rpm. The novelty of this research lies in the use of multi-aperture flushing to improve the machining performance, enable a more uniform GC profile, and minimize the incidence of recast layer.

scholarly journals A study on Electrical Discharge Machining of Titanium Grade2 with experimental and theoretical analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Emmanouil L. Papazoglou ◽  
Panagiotis Karmiris-Obratański ◽  
Beata Leszczyńska-Madej ◽  
Angelos P. Markopoulos
Keyword(s):  
Power Distribution ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Machining Process ◽  
Heat Transfer Analysis ◽  
Machining Parameters ◽  
Machining Performance ◽  
Plasma Flushing Efficiency

AbstractTitanium alloys, due to their unique properties, are utilized in numerous modern high-end applications. Electrical Discharge Machining (EDM) is a non-conventional machining process, commonly used in machining of hard-to-cut materials. The current paper, presents an experimental study regarding the machining of Titanium Grade2 with EDM, coupled with the development of a simulation model. The machining performance indexes of Material Removal Rate, Tool Wear Ratio, and Average White Layer Thickness were measured and calculated for different pulse-on currents and pulse-on times. Moreover, the developed model that integrates a heat transfer analysis with deformed geometry, allows to estimate the power distribution between the electrode and the workpiece, as well as the Plasma Flushing Efficiency, giving an insight view of the process. Finally, by employing the Response Surface Methodology, educed regression models that correlate the machining parameters with the corresponding results, while for all the aforementioned indexes, ANOVA was performed.

scholarly journals Using a Fuzzy Inference System to Obtain Technological Tables for Electrical Discharge Machining Processes

Mathematics ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 922 ◽  
Author(s):  
C. J. Luis Pérez
Keyword(s):  
Fuzzy Inference System ◽  
Electrical Discharge ◽  
Material Removal ◽  
Fuzzy Inference ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Operating Conditions ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Inference System

Technological tables are very important in electrical discharge machining to determine optimal operating conditions for process variables, such as material removal rate or electrode wear. Their determination is of great industrial importance and their experimental determination is very important because they allow the most appropriate operating conditions to be selected beforehand. These technological tables are usually employed for electrical discharge machining of steel, but their number is significantly less in the case of other materials. In this present research study, a methodology based on using a fuzzy inference system to obtain these technological tables is shown with the aim of being able to select the most appropriate manufacturing conditions in advance. In addition, a study of the results obtained using a fuzzy inference system for modeling the behavior of electrical discharge machining parameters is shown. These results are compared to those obtained from response surface methodology. Furthermore, it is demonstrated that the fuzzy system can provide a high degree of precision and, therefore, it can be used to determine the influence of these machining parameters on technological variables, such as roughness, electrode wear, or material removal rate, more efficiently than other techniques.

Analysis of Micro-Pin Manufacturing Using Inverse Slab Electrical Discharge Milling (ISEDM) Process

2011 ◽  
Vol 496 ◽  
pp. 247-252 ◽  
Author(s):  
Ruben Gil ◽  
J.A. Sánchez ◽  
N. Ortega ◽  
S. Plaza ◽  
B. Izquierdo ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Electrical Discharge ◽  
High Speed ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Speed Steel ◽  
Machining Process ◽  
Work Piece ◽  
Electrode Wear ◽  
Pulse Off Time

Abstract. This paper analyses the technological capabilities of a novel rotary (EDM) electrical discharge machining process for the manufacturing of high aspect ratio cylindrical micro-components. The process is called Inverse Electrical Discharge Grinding (ISEDM). An experimental analysis has been carried out on high speed steel (tool steel Vanadis 23), using a conventional EDM machine and graphite electrode. The effect of pulse off-time, work piece final diameter and machining length on material removal rate, electrode wear ratio, radial accuracy and surface roughness has been quantified. From the study, optimum strategies that involve the use of different EDM regimes for achieving the optimum requirements can be defined. Micro-pins of 0.3 mm diameter with aspect ratio as high as 100:1 have been successfully manufactured.

Sign in / Sign up

Export Citation Format

Share Document