Optimization of Process Parameters for Electro-Chemical Machining of EN19

2019 ◽  
pp. 127-142 ◽  
Author(s):  
Divya Zindani ◽  
Nadeem Faisal ◽  
Kaushik Kumar
Keyword(s):  
Process Parameters ◽  
Removal Rate ◽  
Input Parameter ◽  
Electrochemical Machining ◽  
Pso Algorithm ◽  
Machining Process ◽  
Matrix Composites ◽  
Machining Performance ◽  
Electrode Gap ◽  
Optimization Of Process Parameters

Electrochemical machining (ECM) is a non-conventional machining process that is used for machining of hard-to-machine materials. The ECM process is widely used for the machining of metal matrix composites. However, it is very essential to select optimum values of input process parameters to maximize the machining performance. However, the optimization of the output process parameters and hence the machining performance is a difficult task. In this chapter an attempt has been made to carry out single and multiple optimization of the material removal rate (MRR) and the surface roughness (SR) for the ECM process of EN19 using the particle swarm optimization (PSO) technique. The input parameter considered for the optimization are electrolyte concentration (%), voltage (V), feed rate (mm/min), and inter-electrode gap (mm). The optimum value of MRR and SR as found using the PSO algorithm are 0.1847 cm3/min and 25.0612, respectively.

scholarly journals Optimization of Process Parameters During Electrochemical Machining

2019 ◽  
Vol 8 (12) ◽  
pp. 2683-2687
Keyword(s):  
Process Parameters ◽  
Removal Rate ◽  
Research Work ◽  
Electrochemical Machining ◽  
Machining Processes ◽  
Electrode Gap ◽  
Optimization Of Process Parameters ◽  
Finishing Process ◽  
Nimonic 80A ◽  
The Right

Electrochemical machining is one of the most efficient machining processes due to its ability to produce completely stress-free machined components without any need of further finishing process. However, the right understanding of the effects of key factors during machining of various materials is very important to carry out the machining. It is one of the most efficient way of cutting present in modern era. This present paper deals with the electrochemical machining of Nimonic 80A. Design of the experiments are done by using response surface methodology to study the material removal rate and surface roughness. Process parameters such as voltage, tool feed rate, inter-electrode gap and electrolyte concentration has been optimized by using the ANOVA. The regression models are developed to be used as predictive tools. The confirmation test was conducted to validate the results achieved by GRA approach. This research work helps the industrialist for selecting parameters to attain desired outputs.

scholarly journals A review on optimization of machining performances and recent developments in electro discharge machining

2019 ◽  
Vol 6 ◽  
pp. 2 ◽  
Author(s):  
Binayaka Nahak ◽  
Ankur Gupta
Keyword(s):  
Process Parameters ◽  
Removal Rate ◽  
Relevant Literature ◽  
Machining Process ◽  
Machining Performance ◽  
Electro Discharge Machining ◽  
Optimization Of Process Parameters ◽  
Current Voltage ◽  
Recent Developments ◽  
Edm Process

Electro discharge machining (EDM) is a popular unconventional machining process widely employed in die-making industries. Careful selection of process parameters such as pulse current, voltage, on and off time, etc. is essential for machining of hard and conductive materials using EDM. Previous researchers working in the area of EDM have extensively analyzed the machining performance through experimental study, modeling, and simulation and also by theoretical analysis. This article discusses the significant summary of the work performed by earlier researchers through a detailed literature survey. Relevant literature on EDM and impact of process parameters on performance measures such as surface quality, tool wear rate and material removal rate are reviewed. The challenge and limitation of EDM process are also highlighted in this article. It is observed that optimization of process parameters is essentially required for effective and economical machining. So, this article addresses the various issues related to EDM and also provides brief insight into some of the current generation applications of EDM process explored in various industries.

Optimization of electrochemical machining process parameters: Combining response surface methodology and differential evolution algorithm

2016 ◽  
Vol 231 (6) ◽  
pp. 1114-1126 ◽  
Author(s):  
Ali Mehrvar ◽  
Ali Basti ◽  
Ali Jamali
Keyword(s):  
Differential Evolution ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Differential Evolution Algorithm ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Machining Performance ◽  
Evolution Algorithm

Electrochemical machining is a unique prevalent nonconventional manufacturing process used in different industries involving various process parameters, which greatly influence machining performance. Therefore, selection of proper and optimal parameters setting is a challenging issue. In this paper, differential evolution algorithm is applied to look for the optimum solution to this problem. Four parameters, i.e. voltage, tool feed rate, electrolyte flow rate, and electrolyte concentration; and two machining criteria, i.e. material removal rate and surface roughness (Ra) are considered as input variables and responses, respectively. The main purpose is to maximize material removal rate and minimize Ra to achieve better machining performance. In this way, comprehensive mathematical models have first been developed using response surface methodology through experimentation based on central composite design plan. Then, differential evolution algorithm has been utilized for optimizing the process parameters; both single- and multiobjective optimizations are considered, and optimal Pareto front is determined. Finally, optimization result of a trade-off design point in the Pareto front of Ra and material removal rate was also verified experimentally. This machined surface was examined with field-emission scanning electron microscope images. The results showed that the proposed approach is an effective and suitable strategy for optimization of the electrochemical machining process.

Electro Chemical Machining of Aluminum-Boron Carbide-Nanographite Composites

2016 ◽  
Vol 852 ◽  
pp. 136-141 ◽  
Author(s):  
M. Sankar ◽  
A. Gnanavelbabu ◽  
K. Rajkumar ◽  
M. Mariyappan
Keyword(s):  
Boron Carbide ◽  
Process Parameters ◽  
Material Removal ◽  
Solid Lubricant ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Abrasive Particles ◽  
Optimization Of Process Parameters ◽  
Machining Optimization

Non-traditional machining process had made possible the machining of hard to cut materials. Among several non-traditional processes electrochemical machining has been given attention since there occurs no burrs or tool wear. Composites with nano reinforcements had outclassed their counterparts in terms of the properties shown by the nano composites. In the present work aluminium matrix has been reinforced with boron carbide and nano graphite which is added as a solid lubricant to improve tribological properties. The composite is subjected to electrochemical machining with a view of optimizing the process parameters. The process involves introducing abrasive particles while machining which aids in machining. Optimization of process parameters was based on the response surface methodology techniques with four independent input parameters such as voltage, current, electrolytic concentration and feed rate and ECM process performance in terms of material removal rate and overcut.

Study of Pulse Electrochemical Machining Performance of Deep-Small Hole on Nickel-Based Alloy

2011 ◽  
Vol 204-210 ◽  
pp. 1830-1834
Author(s):  
Zhao Long Li ◽  
Shi Chun Di
Keyword(s):  
Base Alloy ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Machining Accuracy ◽  
Machining Performance ◽  
Math Model ◽  
Technical Parameters ◽  
Pulse Electrochemical Machining ◽  
Small Holes

The method of machining deep hole on Ni-base alloy which can tolerant high temperature by pulse electrochemical machining has been proposed in this paper. Five technical parameters are discussed on the effect of mass removal rate of machining process. Establish a dynamic math model, and analyze the effect of process parameters on the mass material removal rate of deep small holes. Machining accuracy of deep small holes was analyzed.

Investigation on the Effect of Multi Wall Carbon Nano Tubes in Wire Electrical Discharge Machining of Hybrid Metal Matrix Composites

2014 ◽  
Vol 592-594 ◽  
pp. 456-460
Author(s):  
S. Ramesh ◽  
N. Natarajan ◽  
Vijayan Krishnaraj ◽  
K. Sathish Kumar
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Characteristics ◽  
Machining Process ◽  
Dielectric Fluid ◽  
Wire Electrical Discharge Machining ◽  
Matrix Composites ◽  
Machining Performance ◽  
Carbon Nano Tubes

Wire Electrical Discharge Machining (WEDM) is an very accurate non-traditional machining process for producing parts with accurate dimensions and complex shapes. The performance of WEDM is measured by evaluating the parameters like Material Removal Rate (MRR), Surface Roughness (Ra), cracks, voids, pores and recast layer. In this paper, an attempt is made to improve the machining performance by adding multi wall carbon nanotube (MWCNT) with dielectric fluid. The MRR, Ra and surface characteristics are compared with surface that is machined using dielectric fluid with and without MWCNT. The results show that addition of MWCNT improves the MRR and surface finish.

Electrochemical machining of 20MnCr5 alloy steel with magnetic flux assisted vibrating tool

2015 ◽  
Vol 231 (10) ◽  
pp. 1956-1965 ◽  
Author(s):  
S Ayyappan ◽  
K Sivakumar ◽  
M Kalaimathi
Keyword(s):  
Magnetic Flux ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Low Frequency ◽  
Full Potential ◽  
Hybrid Technique ◽  
Machining Performance ◽  
Electrode Gap ◽  
Contour Plots ◽  
Control Of Parameters

Utilization of full potential of electrochemical machining (ECM) is not yet achieved because of its lack of accuracy, difficulty in proper tool design and control of parameters. The enhancement of performance of ECM is still a subject of concern in this modern manufacturing world. In this work, low frequency vibrating tool assisted by a magnetic flux was used as an efficient hybrid technique in ECM for improving material removal rate (MRR) and surface roughness (Ra). This paper presents a development of mathematical model correlating MRR and Ra with machining conditions such as voltage, electrolyte concentration, and inter-electrode gap. The significance of ECM process parameters has been investigated using contour plots. The inter-electrode gap (IEG) is considered slightly higher than the maximum tool amplitude that otherwise leads to tool damage. Results indicate that magnetic flux-assisted vibrating tool increases the MRR from 10% to 96%. A magnetic flux-assisted vibrating tool in ECM facilitates and drives out the sludge in the IEG to improve the machining performance. MRR is enhanced due to the movement of ions triggered by magnetic flux, which assures an increase in anodic current. A slight increase in Ra was also noted in comparison to machining with aqueous NaCl electrolyte alone.

Investigations on Machining of Monel 400 Alloys Using Electrochemical Machining with Sodium Nitrate as Electrolyte

2014 ◽  
Vol 592-594 ◽  
pp. 467-472 ◽  
Author(s):  
M. Kalaimathi ◽  
G. Venkatachalam ◽  
Neil Pradeep Makhijani ◽  
Ankit Agrawal ◽  
M. Sivakumar
Keyword(s):  
Process Parameters ◽  
Sodium Nitrate ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Research Field ◽  
Electrode Gap ◽  
Conventional Machine ◽  
Monel 400 ◽  
Physical And Chemical ◽  
The Impact

Monel 400 is a cuprous nickel alloy which is very well-known for its resistivity towards physical and chemical strength. It is probably one of the hardest and most non-corrosive materials known in industrial as well as research field. These properties have enhanced its applications in various fields such as aerospace industries, marine industries, automotive industries etc. Monel 400 alloys are too hard to machine using conventional machine tools and methods as it work hardens rapidly on its surface. Authors concluded that electrochemical machining is the choice of machining of these materials. The present work is carried out to analyze the impact of ECM process parameters such as applied voltage (V), inter-electrode gap (IEG) and electrolyte concentration (EC) on material removal rate (MRR) and surface roughness (Ra). An aqueous sodium nitrate (NaNO3) is used as basic electrolyte in the electrochemical machining of Monel 400 alloys. Response surface methodology (RSM) based central composite design (CCD) is used as experimental strategy. Effects of process parameters as well as their interactions are analysed and the process parameters are optimized.

Process Simulation of Electrochemical Machining of Convexity Structure on Revolving Workpiece

2015 ◽  
Author(s):  
Zengwei Zhu ◽  
Dengyong Wang ◽  
Jun Bao ◽  
Di Zhu
Keyword(s):  
Mathematical Model ◽  
Process Simulation ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Relative Rotation ◽  
Electrode Gap ◽  
Simulation Results

A special electrochemical machining (ECM) process using a revolving cathode tool with hollow windows is presented. Unlike conventional sinking ECM, this presented ECM process fabricates the convexity structures on a revolving part by the relative rotation of anode workpiece and cathode tool. In this paper, a mathematical model is established to describe the evolution of the machining process, the finite element simulations of the new forming fashion are focused for the workpiece’s revolving surface and the convexity’s side profile. The simulation results show that both the cathode feed rate and the applied voltage have significant influence on the equilibrium inter-electrode gap and the material removal rate. The side profile of the convexity is related to radius of the cathode tool. It is expected that the equilibrium gap and steady removal rate could be achieved by optimizing the cathode feed rate and the voltage, the required side profile taper of the convexity could be obtained by selecting the proper tool radius.

scholarly journals Effect on Material Removal Rate and Surface Finish in ECM Process When Machining Stainless Steel-316 with Cu Electrode

2019 ◽  
Vol 8 (4) ◽  
pp. 2933-2941
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Process Parameters ◽  
Surface Finish ◽  
Feed Rate ◽  
Electrolyte Concentration ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Machining Processes

Electrochemical Machining process is one of the popular non-traditional machining processes which is used to machine materials such as super alloys, Ti-alloys, stainless steel etc. Its working principle is based upon Faraday law of electrolysis. The aim of the present work is to optimize the ECM process parameters with the combination of SS 316 (job material) and Copper electrode (tool material). To explore the effect of ECM process parameters such as electrolyte concentration, voltage and current, feed rate on MRR and surface finish (Ra) of the job, total 27 experiments were conducted as per experimental scheme. The results of these experiments revealed that increase in electrolyte concentration decrease the mrr and surface roughness initially increases then decreases. Further, increase in current increases mrr initially and then decreases, surface roughness also increases. It is also noticed that increase in Feed rate mrr decreases and then increases, also surface roughness decreases then increases. Through RSM analysis it is found that the optimum conditions for maximum MRR, and minimum Surface roughness (Ra) is electrolyte concentration 150gm/lit, Voltage 13.5 V & feed 0.8 mm/min. The findings are discussed in the light of previous researches and subsequently conclusions are drawn.

Sign in / Sign up

Export Citation Format

Share Document