Preparation of Porous Ceramic Support with Inorganic Filtration Membrane

Author(s):  
Long Liang ◽  
Jian Bao Li ◽  
Xiao Zhan Yang ◽  
Hong Lin ◽  
Ming Sheng He ◽  
...  
2007 ◽  
Vol 336-338 ◽  
pp. 1099-1101
Author(s):  
Long Liang ◽  
Jian Bao Li ◽  
Xiao Zhan Yang ◽  
Hong Lin ◽  
Ming Sheng He ◽  
...  

2018 ◽  
Vol 156 ◽  
pp. 08015 ◽  
Author(s):  
Muh Amin ◽  
Muhammad Subri

In this study, fabrication and characterization of ceramic membranes preparation was carried out. Porous ceramic membranes were fabricated by extrusion process from different percentage composition of CuZn on (80 wt% Clay, 10 wt% TiO2, 5 wt% Carbon and 5 wt% PVA). The fabricated membranes were sintered at 900°C for 1 hour in an electrical box furnace with heating rate 1oC/min and holding time for 1 hour. Apparent density and porosity were determined by standar methods for ceramic materials. Phase composition of the ceramic support was established by X-Ray Diffraction analysis. SEM studies of the membranes added at different CuZn were carried out.


2008 ◽  
Vol 74 (24) ◽  
pp. 7750-7758 ◽  
Author(s):  
Colin J. Ingham ◽  
Marke Beerthuyzen ◽  
Johan van Hylckama Vlieg

ABSTRACT Within an isogenic microbial population in a homogenous environment, individual bacteria can still exhibit differences in phenotype. Phenotypic heterogeneity can facilitate the survival of subpopulations under stress. As the gram-positive bacterium Lactobacillus plantarum grows, it acidifies the growth medium to a low pH. We have examined the growth of L. plantarum microcolonies after rapid pH downshift (pH 2 to 4), which prevents growth in liquid culture. This acidification was achieved by transferring cells from liquid broth onto a porous ceramic support, placed on a base of low-pH MRS medium solidified using Gelrite. We found a subpopulation of cells that displayed phenotypic heterogeneity and continued to grow at pH 3, which resulted in microcolonies dominated by viable but elongated (filamentous) cells lacking septation, as determined by scanning electron microscopy and staining cell membranes with the lipophilic dye FM4-64. Recovery of pH-stressed cells from these colonies was studied by inoculation onto MRS-Gelrite-covered slides at pH 6.5, and outgrowth was monitored by microscopy. The heterogeneity of the population, calculated from the microcolony areas, decreased with recovery from pH 3 over a period of a few hours. Filamentous cells did not have an advantage in outgrowth during recovery. Specific regions within single filamentous cells were more able to form rapidly dividing cells, i.e., there was heterogeneity even within single recovering cells.


Author(s):  
H.H. Weetall ◽  
W.P. Vann ◽  
W.H. Pitcher ◽  
D.D. Lee ◽  
Y.Y. Lee ◽  
...  

2014 ◽  
Vol 955-959 ◽  
pp. 601-604
Author(s):  
De Xiang Liao ◽  
An Chao Geng ◽  
Peng Hao Su ◽  
Dao Lun Feng ◽  
Lin Lin Wang

The porous ceramic support was realized at various temperature range from 1200°C~1300°C using α-Al2O3 as main material, carbon powder as pore-former, kaolin clay and titanium dioxide as sintering aids and polyvinyl alcohol (PVA) as adhesives. The microstructures of sintered body were significantly affected by the amount of pore-former and sintering temperature. The results indicated that the porosity dramatically increased and the pore radius increased from 2.9 μm to 3.2 μm as carbon powder addition increased from 3 wt.% to 12 wt.%. Correspondingly, their pure water flux depending on the pore structure parameters of the support increased from 1.37 to 4.53 m3.m-2.h-1.bar-1. To prepare porous alumina support with 40% open porosity, carbon powder up to 10 wt.% is appropriate. Sintering experiments showed that the optimum sintering conditions are the sintering temperature of 1300 °C and 2 h holding time at this temperature.


Coatings ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 459 ◽  
Author(s):  
Maksymilian Włodarski ◽  
Matti Putkonen ◽  
Małgorzata Norek

Infrared (IR) spectroscopy is a powerful technique to characterize the chemical structure and dynamics of various types of samples. However, the signal-to-noise-ratio drops rapidly when the sample thickness gets much smaller than penetration depth, which is proportional to wavelength. This poses serious problems in analysis of thin films. In this work, an approach is demonstrated to overcome these problems. It is shown that a standard IR spectroscopy can be successfully employed to study the structure and composition of films as thin as 20 nm, when the layers were grown on porous substrates with a well-developed surface area. In contrast to IR spectra of the films deposited on flat Si substrates, the IR spectra of the same films but deposited on porous ceramic support show distinct bands that enabled reliable chemical analysis. The analysis of Zn-S ultrathin films synthesized by atomic layer deposition (ALD) from diethylzinc (DEZ) and 1,5-pentanedithiol (PDT) as precursors of Zn and S, respectively, served as proof of concept. However, the approach presented in this study can be applied to analysis of any ultrathin film deposited on target substrate and simultaneously on porous support, where the latter sample would be a reference sample dedicated for IR analysis of this film.


Sign in / Sign up

Export Citation Format

Share Document