Experimental Design Methodology in Ball End Milling of C45 Material by Using Tool Tilt Angle - Analysis and Estimation of Surface Roughness Variation

2013 ◽  
Vol 371 ◽  
pp. 48-53 ◽  
Author(s):  
Ioan Pasca ◽  
Mircea Lobonțiu ◽  
Róbert Čep ◽  
Mihai Banica
Keyword(s):  
Surface Roughness ◽  
Tilt Angle ◽  
End Milling ◽  
Milling Process ◽  
Experimental Methodology ◽  
Ball End Mill ◽  
Ball End Milling ◽  
Qualitative And Quantitative ◽  
Tool Tilt Angle ◽  
Experimental Design Methodology

Due to the expansion of milling process with ball end mill in various branches of industry it became necessary for this process to be optimized. For this purpose it is necessary to identify the parameters that influence the process and establish their value for witch the results obtained to be the maximum in terms of qualitative and quantitative. Roughness of the surface machined can be considered as an important element that reflects the degree of successful optimization of this process. In order to solve the problems relating to the analysis and estimation of the surface roughness variation in ball end milling of C45 material with tool tilt angle, in this paper it was designed an experimental methodology followed by analysis of experimental data and estimation of surface roughness variation. The experimental research methodology presented in this paper can be extrapolated and used in a large number of processes.

Evaluation of Surface Roughness in Five-Axis Ball-End Milling

2020 ◽  
pp. 21-31
Author(s):  
B.B. Ponomarev ◽  
S.H. Nguyen
Keyword(s):  
Surface Roughness ◽  
Tilt Angle ◽  
End Milling ◽  
Free Form ◽  
Tool Orientation ◽  
Ball End Milling ◽  
Lead Angle ◽  
Tool Tilt Angle ◽  
Five Axis ◽  
Free Form Surfaces

Unlike three-axis machining, five-axis machining allows the end tool or workpiece to be oriented at any angle relative to the machine axis OZ. It can be achieved by changing the values of the tool tilt angle and lead angle relative to the surface normal in the contact zone of the tool surface and the workpiece, taking into account the direction of the table feed. The article presents experimental results of analyzing the influences of tool orientation on transverse roughness during ball end milling using 2-flute and 4-flute 8 mm diameter mills. The analysis the arithmetic mean deviation of the assessed profile at various values of tool tilt angle and lead angle showed that the position of the tool point with a zero cutting speed significantly affects the surface quality. The results of the evaluation of the tool orientation influence on the surface roughness enable the selection of optimal tool orientation angles when developing control programs for end milling of free-form surfaces on five-axis CNC milling machines.

Intelligent Monitoring and Prediction of Surface Roughness in Ball-End Milling Process

2011 ◽  
Vol 121-126 ◽  
pp. 2059-2063 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Angsumalin Senjuntichai
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Prediction Accuracy ◽  
End Milling ◽  
Milling Process ◽  
Ball End Milling ◽  
Roughness Model ◽  
Force Ratio ◽  
Tool Diameter ◽  
End Milling Process

In order to realize the intelligent machines, the practical model is proposed to predict the in-process surface roughness during the ball-end milling process by utilizing the cutting force ratio. The ratio of cutting force is proposed to be generalized and non-scaled to estimate the surface roughness regardless of the cutting conditions. The proposed in-process surface roughness model is developed based on the experimentally obtained data by employing the exponential function with five factors of the spindle speed, the feed rate, the tool diameter, the depth of cut, and the cutting force ratio. The prediction accuracy and the prediction interval of the in-process surface roughness model at 95% confident level are calculated and proposed to predict the distribution of individually predicted points in which the in-process predicted surface roughness will fall. All those parameters have their own characteristics to the arithmetic surface roughness and the surface roughness. It is proved by the cutting tests that the proposed and developed in-process surface roughness model can be used to predict the in-process surface roughness by utilizing the cutting force ratio with the highly acceptable prediction accuracy.

Surface Roughness Prediction in Ball-End Milling Process for Aluminum by Using Air Blow Cutting

2011 ◽  
Vol 418-420 ◽  
pp. 1428-1434 ◽  
Author(s):  
Keerati Karunasawat ◽  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
End Milling ◽  
Cutting Speed ◽  
Milling Process ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Ball End Milling ◽  
Tool Diameter ◽  
End Milling Process

The objective of this research is to develop the surface roughness and cutting force models by using the air blow cutting of the aluminum in the ball-end milling process. The air blow cutting proposed in order to reduce the use of the cutting fluid. The surface roughness and cuttting force models are proposed in the exponential forms which consist of the cutting speed, the feed rate, the depth of cut, the tool diameter, and the air blow pressure. The coefficients of the surface roughness and cutting force models are calculated by utilizing the multiple regression with the least squared method at 95% significant level. The effects of cutting parameters on the cutting force are investigated and measured to analyze the relation between the surface roughness and the cutting conditions. The experimentally obtained results showed that the cutting force has the same trend with the surface roughness. The surface plots are constructed to determine the optimum cutting condition referring to the minimum surface roughness.

Effect of Tool Tilting Angle on Tool Wear and Surface Roughness in Micro Ball End Milling

2011 ◽  
Vol 325 ◽  
pp. 606-611 ◽  
Author(s):  
Kazuya Hamaguchi ◽  
Yuji Kagata ◽  
Hiroo Shizuka ◽  
Koichi Okuda
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Flank Wear ◽  
End Milling ◽  
Depth Of Cut ◽  
End Mill ◽  
Ball End Mill ◽  
Ball End Milling ◽  
Tilting Angle ◽  
Radial Depth

This paper describes the effect of the tool tilting angle on the tool wear and the surface roughness in micro ball end milling. The cutting tests of hardened stainless steel were carried out by using of the micro ball end mill with radius of 100mm under the conditions of tilting angle from 0° to 45°. The spindle speed was fixed in a constant of 120,000 min-1. The feed per tooth, axial depth of cut and radial depth of cut were also fixed. The flank wear, the surface roughness and the cutting force were investigated. As a result, the maximum width of flank wear of the micro ball end mill tended to decrease with an increase in the tilting angle of spindle. The surface roughness became almost constant not depending on the tilting angle of the spindle.

Investigation of Dry Cutting and Applications of Cutting Fluid in Ball-End Milling Process

2011 ◽  
Vol 291-294 ◽  
pp. 3013-3023 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Channarong Rungruang
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
End Milling ◽  
Cutting Parameters ◽  
Milling Process ◽  
Cutting Fluid ◽  
Cutting Condition ◽  
Dry Cutting ◽  
Ball End Milling ◽  
End Milling Process

In order to realize the environmental hazard, this paper presents the investigation of the machinability of ball-end milling process with the dry cutting, the wet cutting, and the mist cutting for aluminum. The relations of the surface roughness, the cutting force, and the cutting parameters are examined based on the experimental results by using the Response Surface Analysis with the Box-Behnken design. The in-process cutting force is monitored to analyze the relations of the surface roughness and the cutting parameters. The proper cutting condition can be determined easily referring to the minimum use of cutting fluid, and the minimum surface roughness and cutting force of the surface plot. The effectiveness of the obtained surface roughness and cutting force models have been proved by utilizing the analysis of variance at 95% confident level.

A wavelet approach to predict surface roughness in ball-end milling

2015 ◽  
Vol 231 (14) ◽  
pp. 2468-2478 ◽  
Author(s):  
Somkiat Tangjitsitcharoen ◽  
Prae Thesniyom ◽  
Suthas Ratanakuakangwan
Keyword(s):  
Surface Roughness ◽  
Wavelet Transform ◽  
Cutting Force ◽  
Cutting Forces ◽  
End Milling ◽  
Detection System ◽  
Milling Process ◽  
Cutting Conditions ◽  
Ball End Milling ◽  
Dynamic Cutting Force

This research proposed an advance in the prediction of the in-process surface roughness during the ball-end milling process by utilizing the wavelet transform to monitor and decompose the dynamic cutting forces. The chatter detection system has been adopted from the previous research of the author to avoid the chatter first, and hence, the dynamic cutting force ratio is introduced to predict the in-process surface roughness during the normal cutting by taking the ratio of the decomposed dynamic cutting force in X axis to that in Z axis. The Daubechies wavelet transform is employed in this research to analyze the in-process surface roughness. The experimentally obtained results showed that the surface roughness frequency occurred at the same level of the decomposed dynamic cutting forces although the cutting conditions are changed. It is understood that the in-process surface roughness can be predicted effectively under various cutting conditions referring to the proposed monitoring system.

Sign in / Sign up

Export Citation Format

Share Document