Structure Synthesis of 3-RRS Type Spatial Compliant Parallel Manipulator

2010 ◽  
Vol 44-47 ◽  
pp. 1375-1379
Author(s):  
Da Chang Zhu ◽  
Li Meng ◽  
Tao Jiang
Keyword(s):  
Parallel Manipulator ◽  
Compliant Mechanisms ◽  
Screw Theory ◽  
Weight Ratio ◽  
Parallel Manipulators ◽  
Robot System ◽  
New Approach ◽  
Structure Synthesis ◽  
Rigid Joints ◽  
Type 3

Parallel manipulators has been extensively studied by virtues or its high force-to-weight ratio and widely spread applications such as vehicle or flight simulator, a machine tool and the end effector of robot system. However, as each limb includes several rigid joints, assembling error is demanded strictly, especially in precision measurement and micro-electronics. On the other hand, compliant mechanisms take advantage of recoverable deformation to transfer or transform motion, force, or energy and the benefits of compliant mechanisms mainly come from the elimination of traditional rigid joints, but the traditional displacement method reduce the stiffness of spatial compliant parallel manipulators. In this paper, a new approach of structure synthesis of 3-DoF rotational compliant parallel manipulators is proposed. Based on screw theory, the structures of RRS type 3-DoF rotational spatial compliant parallel manipulator are developed. Experiments via ANSYS are conducted to give some validation of the theoretical analysis.

Geometrical method to determine the reciprocal screws and applications to parallel manipulators

Robotica ◽  
2009 ◽  
Vol 27 (6) ◽  
pp. 929-940 ◽  
Author(s):  
Jianguo Zhao ◽  
Bing Li ◽  
Xiaojun Yang ◽  
Hongjian Yu
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Singularity Analysis ◽  
Algebraic Manipulation ◽  
Robot Kinematics ◽  
Geometrical Approach ◽  
New Approach ◽  
Geometrical Relation ◽  
Manipulator Design

SUMMARYScrew theory has demonstrated its wide applications in robot kinematics and statics. We aim to propose an intuitive geometrical approach to obtain the reciprocal screws for a given screw system. Compared with the traditional Plücker coordinate method, the new approach is free from algebraic manipulation and can be used to obtain the reciprocal screws just by inspecting the structure of manipulator. The approach is based on three observations that describe the geometrical relation for zero pitch screw and infinite pitch screw. Based on the observations, the reciprocal screw systems of several common kinematic elements are analyzed, including usual kinematic pairs and chains. We also demonstrate usefulness of the geometrical approach by a variety of applications in mobility analysis, Jacobian formulation, and singularity analysis for parallel manipulator. This new approach can facilitate the parallel manipulator design process and provide sufficient insights for existing manipulators.

Type Synthesis of Uncoupled 2T2R Parallel Manipulators

2012 ◽  
Author(s):  
Yanbin Zhang ◽  
Kwun-lon Ting
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Control Design ◽  
Parallel Manipulators ◽  
Velocity Space ◽  
Type Synthesis ◽  
Systematic Method ◽  
Structure Synthesis ◽  
Hybrid Manipulator ◽  
Actuated Joints

This paper presents a simple and systematic method for type synthesis of four-degree-of-freedom uncoupled parallel manipulators with two-translational and two-rotational (2T2R) motion components. Based on the concept of hybrid manipulator, one uncoupled 2T2R hybrid manipulator, which is composed of one full-isotropic planar 2T1R parallel manipulator and one revolute joint in serial assembly, is designed first. Then the structure synthesis of the fourth leg of 2T2R parallel manipulator is performed in terms of the reciprocal screw theory. Finally, the type synthesis of uncoupled 2T2R parallel manipulators is realized by combining the uncoupled 2T2R hybrid manipulator and one of the synthesized fourth legs. The Jacobian of the uncoupled 2T2R parallel manipulator is a 4×4 diagonal matrix. Therefore, there exists a one-to-one correspondence between the input velocity space of the actuated joints and the output velocity space of the moving platform. Moreover, both the control design and the path planning of these proposed manipulators are very simple.

A Spatial 3-DOF Translational Compliant Parallel Manipulator

2010 ◽  
Vol 34-35 ◽  
pp. 143-147 ◽  
Author(s):  
Da Chang Zhu ◽  
Yan Ping Feng
Keyword(s):  
Parallel Manipulator ◽  
Piezoelectric Actuators ◽  
Parallel Manipulators ◽  
Flexure Hinge ◽  
Cartesian Coordinate System ◽  
Optimal Method ◽  
New Approach ◽  
And Topology ◽  
Structure Synthesis ◽  
Cartesian Coordinate

A new approach of structure synthesis of 3-DoF compliant parallel manipulators with flexure hinge is proposed in this paper. Based on characteristics of flexure hinge and topology optimal method, the kinematics of the 3-DOF perpendicular compliant parallel manipulator with flexure hinge and its control system are developed. The parallel manipulator is driven by three piezoelectric actuators and the three actuators in this mechanism are arranged according to the Cartesian coordinate system. Experiments are conducted to give some validation of the theoretical analysis.

Type Synthesis of 3-DOF Spherical Parallel Manipulators Based on Screw Theory1

2004 ◽  
Vol 126 (1) ◽  
pp. 101-108 ◽  
Author(s):  
Xianwen Kong ◽  
Cle´ment M. Gosselin
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
General Procedure ◽  
Kinematic Chain ◽  
Parallel Manipulators ◽  
Type Synthesis ◽  
Validity Condition ◽  
First Time ◽  
Spherical Parallel Manipulator ◽  
Selection Of

A spherical parallel manipulator (SPM) refers to a 3-DOF (degree-of-freedom) parallel manipulator generating 3-DOF spherical motion. A method is proposed for the type synthesis of SPMs based on screw theory. The wrench systems of a spherical parallel kinematic chain (SPKC) and its legs are first analyzed. A general procedure is then proposed for the type synthesis of SPMs. The type synthesis of legs for SPKCs, the type synthesis of SPKCs, as well as the selection of inputs of SPMs are dealt with in sequence. An input validity condition of SPMs is proposed. SPKCs with and without inactive joints are synthesized. The number of overconstraints of each SPKC is also given. The phenomenon of dependent joint groups in an SPKC is revealed for the first time.

An efficient method for the dynamic modeling and analysis of Stewart parallel manipulator based on the screw theory

2019 ◽  
Vol 234 (3) ◽  
pp. 808-821
Author(s):  
Yulei Hou ◽  
Guoxing Zhang ◽  
Daxing Zeng
Keyword(s):  
Dynamic Model ◽  
Dynamic Modeling ◽  
Parallel Manipulator ◽  
Inverse Dynamics ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Force Balance ◽  
Constraint Matrix ◽  
Scheme Design ◽  
Control Scheme

Dynamic modeling serves as the fundamental basis for dynamic performance analysis and is an essential aspect of the control scheme design of parallel manipulators. This report presents a concise and efficient solution to the dynamics of Stewart parallel manipulators based on the screw theory. The initial pose of these manipulators is described. Then the pose matrix of each link of the Stewart parallel mechanism is obtained using an inverse kinematics solution and an exponential product formula. Considering the constraint relationship between joints, the constraint matrix of the Stewart parallel manipulator is deduced. In addition, the Jacobian matrix and the twist of each link are obtained. Moreover, by deriving the differential form of the constraint matrix, the spatial acceleration of each link is obtained. Based on the force balance relationship of each link, the inverse dynamics and the general form of the dynamic model of the Stewart parallel manipulator is established and the process of inverse dynamics is summarized. The dynamic model is then verified via dynamic simulation using the ADAMS software. A numerical example is considered to demonstrate the feasibility and effectiveness of this model. The proposed dynamic modeling approach serves as a fundamental basis for structural optimization and control scheme design of the Stewart parallel manipulators.

A 2(3-RRPS) parallel manipulator inspired by Gough–Stewart platform

Robotica ◽  
2012 ◽  
Vol 31 (3) ◽  
pp. 381-388 ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Mario A. García-Murillo ◽  
Eduardo Castillo-Castaneda
Keyword(s):  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Forward Kinematics ◽  
Triangular Prism ◽  
Input Output ◽  
Six Degrees Of Freedom ◽  
Moving Platform

SUMMARYThis study addresses the kinematics of a six-degrees-of-freedom parallel manipulator whose moving platform is a regular triangular prism. The moving and fixed platforms are connected to each other by means of two identical parallel manipulators. Simple forward kinematics and reduced singular regions are the main benefits offered by the proposed parallel manipulator. The Input–Output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. A case study, which is verified with the aid of commercially available software, is included with the purpose to exemplify the application of the method of kinematic analysis.

Kinematic analyses of novel translational parallel manipulators

2013 ◽  
Vol 228 (2) ◽  
pp. 330-341 ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Horacio Orozco-Mendoza ◽  
Alvaro Sánchez-Rodríguez ◽  
Gursel Alici
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Linear Equations ◽  
Parallel Manipulators ◽  
Output Displacement ◽  
Kinematic Analyses ◽  
Linear Actuators ◽  
The One ◽  
Forward Kinematic ◽  
Primary Contribution

This study reports on the kinematic analyses of four translational parallel manipulators (3RPC, SPS + 2RPC, RPPR + 2RPC and RPPR + 2PPP) articulated with linear actuators. They are based on serially connected chains which are connected with cylindrical (C), prismatic (P), revolute (R), spherical (S) and universal (U) joints. Of these manipulators, the one which is a fully decoupled, fully isotropic and singularity-free translational parallel manipulator (RPPR+2PPP) offers a one-to-one correspondence between its input and output displacement. This makes its forward and inverse position analyses simpler with a set of linear equations to be solved. Although the other manipulators have coupled kinematics, they still have simpler forward kinematic equations over other well-known translational parallel manipulators reported in the literature. We also employ screw theory to undertake the velocity and acceleration analyses. The primary contribution of this manuscript is to show how the 3-RPC translational parallel manipulator can be gradually modified in order to obtain a fully isotropic, fully decoupled and singularity-free translational parallel manipulator.

scholarly journals A Five-Bar Planar Parallel Manipulator with Two End-Effectors

2018 ◽  
Author(s):  
Jaime Gallardo-Alvarado ◽  
Ramon Rodriguez-Castro ◽  
Luciano Perez-Gonzalez ◽  
Carlos R. Aguilar-Najera ◽  
Alvaro Sanchez-Rodriguez
Keyword(s):  
Parallel Manipulator ◽  
Screw Theory ◽  
Parallel Manipulators ◽  
Intermediate Step ◽  
Euclidean Group ◽  
Planar Parallel Manipulator ◽  
Special Software ◽  
End Effectors ◽  
Klein Form

Parallel manipulators with multiple end-effectors bring us interesting advantages over conventional parallel manipulators such as improved manipulability, workspace and avoidance of singularities. In this work the kinematics of a five-bar planar parallel manipulator equipped with two end-effectors is approached by means of the theory of screws. As an intermediate step the displacement analysis of the robot is also investigated. The input-output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. In that regard the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) plays a central role. In order to exemplify the method of kinematic analysis, a case study is included. Furthermore, the numerical results obtained by means of the theory of screws are confirmed with the aid of special software like ADAMS.TM

Workspace Analysis and Going through Singularities of 5-Bar Symmetric Planar Parallel Manipulator by Automated Selective Actuation Mechanism

2012 ◽  
Vol 588-589 ◽  
pp. 1664-1668
Author(s):  
Syam Sundar ◽  
Vijay S. Rathore ◽  
Manoj K. Sahi ◽  
V. Upendran ◽  
Anjan Kumar Dash
Keyword(s):  
Closed Form ◽  
Parallel Manipulator ◽  
Parallel Manipulators ◽  
New Approach ◽  
Serial Manipulators ◽  
Actuation Mechanism ◽  
Geometric Conditions ◽  
Workspace Analysis ◽  
Planar Parallel Manipulator ◽  
Planar Parallel Manipulators

In this article‚ a new approach is presented to determine the various shapes of workspaces of 5 bar symmetric planar parallel manipulators. Here the shape of the workspace is determined by the number of ways the workspaces of the two serial manipulators intersect with each other. Geometric conditions are established in each case and area of each shape of workspace is determined in closed form. Singularity is another important consideration in the design of parallel manipulators. In this paper, an approach is presented to go through the singularity points using an automatic selective actuation mechanism. A prototype 5-bar planar manipulator is fabricated along with an automatic selective actuation mechanism demonstrating the manipulator going through the singularity points.

Differential kinematics of parallel manipulators using Assur virtual chains

2009 ◽  
Vol 223 (7) ◽  
pp. 1697-1711 ◽  
Author(s):  
A Campos ◽  
R Guenther ◽  
D Martins
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Screw Theory ◽  
Kinematic Chain ◽  
Parallel Manipulators ◽  
Kinematic Constraints ◽  
Passive Joint ◽  
Planar Parallel Manipulator ◽  
Stewart Gough Platform ◽  
Homogeneous Linear

This article introduces the concept of Assur virtual chains and its applications in differential kinematics of parallel manipulators. Using Assur virtual chains, the differential kinematics has a simple matricial formulation and the choice between direct and inverse kinematics is reduced to select primary variables in a homogeneous linear system. Assur virtual chains are also useful for obtaining information about the relative movements or to imposing particular kinematic constraints between two links of a kinematic chain. Additionally, a new systematic algorithm is established to analytically eliminate passive joint velocities and calculate the Jacobian matrices. This elimination approach is based on screw theory concepts such as twist, wrench, and reciprocity; also, graph theory is used for kinematic chain representation. At the end of the article, the method is applied to a 3RRR planar parallel manipulator and a general universal-prismatic-spheric Stewart—Gough platform.

Sign in / Sign up

Export Citation Format

Share Document