Design, fabrication, and testing of an active camber rotor blade tip

This paper presents a morphing blade design for wind turbine application with flexibility in chord-wise bending while providing sufficient stiffness to carry the aerodynamic loads. The NACA64 profile is selected for the camber morphing blade demonstrator. A corrugation concept is chosen because it is relatively easy to manufacture and provides sufficient stiffness to resist deformation due to the aerodynamic loads (through the provision of effective stringers) while providing the required flexibility for chord-wise bending. A mechanical actuation mechanism is employed to achieve the desired morphing angle and increase the stiffness of the morphing airfoil section to resist aerodynamic loading. The design of a morphing blade demonstrator is presented together with the manufacturing process. Finally, an experimental study is conducted where the morphing angle is measured for increasing actuation load and compared with FE analysis showing good agreement between the experimental results and results from the finite element analysis in addition to achieving the desired morphing angle.

A review of wear resistance materials used in power-screw mechanism for aerospace applications

In today’s industrial requirement, good wear resistant materials with the same or better mechanical properties are the need of the hour. In the present paper, an actuator that is used to lift the load is under study. It uses a linear actuation mechanism involving a screw-like motion to lift the loads. It employs a stainless steel of high quality. Since there are various types of wearing involved in the system, choice of the materials becomes the prime factor for determining the maintenance cost and the cycle life of the actuator. There are many research advances made in this field which provides us with the best type of material for its particular type of job. The present paper discusses the materials that could be substituted in place of the existing material choice i.e., in place of AMS5659 and aluminium-bronze. The two materials stated above are known for its superior wear handling and excellent mechanical properties.

Kinematic Analysis of a Parallel Manipulator Driven by Perpendicular Linear Actuators

In this paper, a goniometer-type specimen stage with a linear actuation mechanism mounted on a rotation mechanism is introduced. The linear actuation mechanism was modeled as a spatial parallel manipulator consisting of a moving body, three linear actuators, and an anti-rotation mechanism. The three linear actuators were arranged perpendicular to each other. In the specimen stage, the linear actuators were in ball contact with the surface of a holder designed to hold a specimen. For the parallel manipulator, the ball contact was replaced with two prismatic joints and a spherical joint. The mobility of the manipulator without the anti-rotation mechanism was one degree of freedom greater than the number of actuators. Therefore, the redundant one degree-of-freedom motion was restrained using an anti-rotation mechanism with three rotation joints and two prismatic joints. The inverse and direct kinematics of the goniometer mechanism were derived and verified. In addition, the inverse Jacobian was derived, and local and global performance indices were analyzed by the terms of manipulability and isotropy. Finally, the goniometer-type specimen stage was designed by the global performance indices.

Design and Implementation of Morphed Multi-Rotor Vehicles with Real-Time Obstacle Detection and Sensing System

Multirotor unmanned aerial vehicles (MUAVs) are becoming more prominent for diverse real-world applications due to their inherent hovering ability, swift manoeuvring and vertical take-off landing capabilities. Nonetheless, to be entirely applicable for various obstacle prone environments, the conventional MUAVs may not be able to change their configuration depending on the available space and perform designated missions. It necessitates the morphing phenomenon of MUAVS, wherein it can alter their geometric structure autonomously. This article presents the development of a morphed MUAV based on a simple rotary actuation mechanism capable of driving each arm’s smoothly and satisfying the necessary reduction in workspace volume to navigate in the obstacle prone regions. The mathematical modelling for the folding mechanism was formulated, and corresponding kinematic analysis was performed to understand the synchronous motion characteristics of the arms during the folding of arms. Experiments were conducted by precisely actuating the servo motors based on the proximity ultrasonic sensor data to avoid the obstacle for achieving effective morphing of MUAV. The flight tests were conducted to estimate the endurance and attain a change in morphology of MUAV from “X-Configuration” to “H-Configuration” with the four arms actuated synchronously without time delay.

Yoshimura-origami Based Earthworm-like Robot With 3-dimensional Locomotion Capability

Earthworm-like robots have received great attention due to their prominent locomotion abilities in various environments. In this research, by exploiting the extraordinary three-dimensional (3D) deformability of the Yoshimura-origami structure, the state of the art of earthworm-like robots is significantly advanced by enhancing the locomotion capability from 2D to 3D. Specifically, by introducing into the virtual creases, kinematics of the non-rigid-foldable Yoshimura-ori structure is systematically analyzed. In addition to exhibiting large axial deformation, the Yoshimura-ori structure could also bend toward different directions, which, therefore, significantly expands the reachable workspace and makes it possible for the robot to perform turning and rising motions. Based on prototypes made of PETE film, mechanical properties of the Yoshimura-ori structure are also evaluated experimentally, which provides useful guidelines for robot design. With the Yoshimura-ori structure as the skeleton of the robot, a hybrid actuation mechanism consisting of SMA springs, pneumatic balloons, and electromagnets is then proposed and embedded into the robot: the SMA springs are used to bend the origami segments for turning and rising motion, the pneumatic balloons are employed for extending and contracting the origami segments, and the electromagnets serve as anchoring devices. Learning from the earthworm’s locomotion mechanism--retrograde peristalsis wave, locomotion gaits are designed for controlling the robot. Experimental tests indicate that the robot could achieve effective rectilinear, turning, and rising locomotion, thus demonstrating the unique 3D locomotion capability.

A Novel Power-Amplified Jumping Behavior in Larval Beetles (Coleoptera: Laemophloeidae)

Larval insects use many methods for locomotion. Here we describe a previously unknown jumping behavior in a group of beetle larvae (Coleoptera: Laemophloeidae). We analyze and describe this behavior in Laemophloeus biguttatus and provide information on similar observations for another laemophloeid species, Placonotus testaceus. Laemophloeus biguttatus larvae prelude jumps by arching their body while gripping the substrate with their legs over a period of 0.22 ± 0.17s. This is followed by a rapid ventral curling of the body after the larvae releases its grip that launches them into the air. Larvae reached takeoff velocities of 0.47 ± 0.15 m s-1 and traveled 11.2 ± 2.8 mm (1.98 ± 0.8 body lengths) horizontally and 7.9 ± 4.3 mm (1.5 ± 0.9 body lengths) vertically during their jumps. Conservative estimates of power output revealed that not all jumps can be explained by direct muscle power alone, suggesting Laemophloeus biguttatus uses a latch-mediated spring actuation mechanism (LaMSA) in which interaction between the larvae’s legs and the substrate serves as the latch. MicroCT scans and SEM imaging of larvae did not reveal any notable modifications that would aid in jumping. Although more in-depth experiments could not be performed to test hypotheses on the function of these jumps, we posit that this behavior is used for rapid locomotion which is energetically more efficient than crawling the same distance to disperse from their ephemeral habitat. We also summarize and discuss jumping behaviors among insect larvae for additional context of this behavior in laemophloeid beetles.