scholarly journals Effect of Micro-EDM Parameters on Material Removal Rate of Nonconductive ZrO2 Ceramic

2013 ◽  
Vol 465-466 ◽  
pp. 1329-1333 ◽  
Author(s):  
Abdus Sabur ◽  
Abdul Moudood ◽  
Mohammad Yeakub Ali ◽  
Mohammad Abdul Maleque
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Carbon Layer ◽  
Machining Process ◽  
Machining Parameters ◽  
Micro Edm ◽  
Machined Surface ◽  
Electro Discharge Machining

Micro-electro discharge machining (micro-EDM) technique, an advanced noncontact machining process, is used for structuring of nonconductive ZrO2 ceramic. In this study copper foil as a conductive layer is adhered on the workpiece surface to initiate the sparks and kerosene is used as dielectric for creation of continuous conductive pyrolytic carbon layer on the machined surface. Voltage (V) and capacitance (C) are considered as the parameters to investigate the process capability of machining parameters in continuous micro-EDM of ZrO2. Different voltage pulses are studied to examine the causes of lower material removal rate (MRR) in micro-EDM of nonconductive ceramics. The results showed that in micro-EDM of ZrO2 MRR increases with the increase of voltage and capacitance initially, but decreases at higher values and no significant materials are removed at capacitances higher than 1nF.

Modelling of Material Removal Rate in EDM of Nonconductive ZrO2 Ceramic by Taguchi Method

2013 ◽  
Vol 393 ◽  
pp. 246-252 ◽  
Author(s):  
A. Sabur ◽  
Mohammad Yeakub Ali ◽  
M.A. Maleque
Keyword(s):  
Taguchi Method ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Pyrolytic Carbon ◽  
Carbon Layer ◽  
Machining Process ◽  
Machined Surface ◽  
Pulse On Time ◽  
Pulse Off Time

Electro discharge machining (EDM) technique, a noncontact machining process, is applied for structuring nonconductive ZrO2 ceramic. A conductive layer of adhesive copper is applied on the workpiece surface to initiate the sparks. Kerosene is used as dielectric for creation of continuous conductive pyrolytic carbon layer on the machined surface. Experiments are conducted by varying the peak current (Ip), pulse-on time (Ton), pulse-off time (Toff) and gap voltage (Vg). Correlating these variables a mathematical model for material removal rate (MRR) is developed using Taguchi method. The optimized parametric conditions are determined for higher MRR through ANOVA and signal to noise (S/N) ratio analysis. The results showed that the Ip and Ton are the significant parameters of MRR in EDM for nonconductive ZrO2 ceramic. The model also showed that MRR increases with the increase of Ip and Ton, but the process is controlled by Ip as a whole.

scholarly journals Tool Wear Rate Prediction by using Optimization Techniques

2019 ◽  
Vol 9 (2) ◽  
pp. 1271-1277
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Optimization Techniques ◽  
Machining Process ◽  
Machining Parameters ◽  
Tungsten Carbides ◽  
Electro Discharge Machining ◽  
Pulse On Time

Electro discharge machining is a non-traditional machining process used for machining hard-to-machine materials, such as various grades of titanium alloys, heat-treated alloy steels, composites, tungsten carbides, and so forth. These materials are hard to machine with customary machining procedures like drilling, milling and hence electro-discharge machining is used to machine such materials to get better quality and efficiency. These materials are generally utilized in current industries like die making industries, aeronautics, nuclear industries, and medical fields. This type of machining is thermalbased, and machining takes place due to repetitive electric sparks that generate between workpiece and tool. Both tools and workpieces are inundated in a dielectric liquid, which has two primary functions. In the first place, it behaves like a medium between the work metal and the tool. Second, it is a flushing agent to expel the machined metal from the machined zone. Machining parameters like a pulse on time, current, wire feed the tool and gap voltage affect the output responses like surface roughness and material removal rate. The material removal rate is a significant parameter that determines machining efficiency. Surface roughness is also a vital parameter that decides machining quality. A lot of research has been conducted to determine the optimum parameters for obtaining the best results. In the present work, a comprehensive review of different types of EDM and the effect of various machining parameters on the surface roughness, material removal rate, and other response parameters has been done.

Determination of Material Removal Rate and Radial Overcut in Electro Discharge Machining of AISI 304 Using Dimensional Analysis

2016 ◽  
Vol 852 ◽  
pp. 160-165 ◽  
Author(s):  
Munmun Bhaumik ◽  
Kalipada Maity ◽  
Kasinath Das Mohapatra
Keyword(s):  
Dimensional Analysis ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Aisi 304 ◽  
Radial Overcut ◽  
Electro Discharge Machining ◽  
Work Material

Electro discharge machining (EDM) is a most commonly used machining process among all the non-conventional machining process which removes materials via electrical and thermal energy. The primary goal of EDM is to get more material removal rate (MRR) with lower radial overcut (ROC). Normally, the responses are predicted using empirical models which are limited to only machining parameters and they do not consider the effects of work material properties on the process performance. Therefore in this study, a model has been developed including machining parameter as well as thermo-physical property of work material. In this investigation, a semi-empirical model has been established for the material removal rate (MRR) and radial overcut (ROC) by adopting the dimensional analysis technique. Dimensional analysis is a technique of dimensions and a mathematical technique that deals with the physical quantities concerned with the experiments to formulate a model for the response in terms of response control parameters as well as some physical properties of the materials. Buckingham’s л theorem is a main theorem in dimensional analysis and it is a signification of Rayleigh’s method of dimensional analysis. The theory is applied to gather each and every variable presenting the problem in a number of the dimensionless products. For this study, the thermo-physical properties viz. density, thermal conductivity and coefficient of thermal expansion and machining parameters like peak current, pulse on time, gap voltage and duty cycle are considered as input factor. AISI 304 stainless steel used as work material and Tungsten carbide is used as tool material for this investigation.

scholarly journals An Experimental Study on the Precision Abrasive Machining Process of Hard and Brittle Materials with Ultraviolet-Resin Bond Diamond Abrasive Tools

Materials ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 125 ◽  
Author(s):  
Lei Guo ◽  
Xinrong Zhang ◽  
Shibin Chen ◽  
Jizhuang Hui
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Manufacturing Process ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Abrasive Machining ◽  
Machining Performance ◽  
Machined Surface ◽  
Ultraviolet Curable

Ultraviolet-curable resin was introduced as a bonding agent into the fabrication process of precision abrasive machining tools in this study, aiming to deliver a rapid, flexible, economical, and environment-friendly additive manufacturing process to replace the hot press and sintering process with thermal-curable resin. A laboratory manufacturing process was established to develop an ultraviolet-curable resin bond diamond lapping plate, the machining performance of which on the ceramic workpiece was examined through a series of comparative experiments with slurry-based iron plate lapping. The machined surface roughness and weight loss of the workpieces were periodically recorded to evaluate the surface finish quality and the material removal rate. The promising results in terms of a 12% improvement in surface roughness and 25% reduction in material removal rate were obtained from the ultraviolet-curable resin plate-involved lapping process. A summarized hypothesis was drawn to describe the dynamically-balanced state of the hybrid precision abrasive machining process integrated both the two-body and three-body abrasion mode.

Comparative evaluation of powder-mixed and ultrasonic-assisted rough die-sinking electrical discharge machining based on pulse characteristics

2019 ◽  
Vol 233 (14) ◽  
pp. 2515-2530 ◽  
Author(s):  
R Rajeswari ◽  
MS Shunmugam
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Graphite Powder ◽  
Machining Process ◽  
Machined Surface ◽  
Ultrasonic Assisted ◽  
Pulse On Time

Electrical discharge machining is used in the machining of complicated shapes in hardened molds and dies. In rough die-sinking stage, attempts are made to enhance material removal rate with a consequential reduction in cycle time. Powder mix and ultrasonic assistance are employed in the electrical discharge machining process to create gap conditions favoring material removal. In the present work, experiments are carried out on hardened D3 die steel using full-factorial design based on three levels of voltage, current and pulse on time. The gap phenomena in graphite powder-mixed and ultrasonic-assisted rough electrical discharge machining are studied using a detailed analysis of pulse shapes and their characteristic trains. Two new parameters, namely, energy expended over a second ( E) and performance factor ( PF) denoting the ratio of energy associated with sparks to total discharge energy, bring out gap conditions effectively. In comparison with the conventional electrical discharge machining for the selected condition, it is seen that the graphite powder mixed in the dielectric enhances the material removal rate by 20.8% with E of 215 J and PF of 0.227, while these values are 179.8 J and 0.076 for ultrasonic-assisted electrical discharge machining with marginal reduction of 3.9%. Cross-sectional images of workpieces also reveal the influence of electrical discharge machining conditions on the machined surface. The proposed approach can be extended to different powder mix and ultrasonic conditions to identify condition favoring higher material removal.

Statistical analysis of material removal rate and surface roughness in electrical discharge turning of titanium alloy (Ti-6Al-4V)

2016 ◽  
Vol 232 (9) ◽  
pp. 1603-1614 ◽  
Author(s):  
Vikas Gohil ◽  
Yogesh M Puri
Keyword(s):  
Surface Roughness ◽  
Titanium Alloy ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Peak Current ◽  
Pulse On Time

Electrical discharge turning is a unique form of electrical discharge machining process, which is being especially developed to generate cylindrical forms and helical profiles on the difficult-to-machine materials at both macro and micro levels. A precise submerged rotating spindle as a work holding system was designed and added to a conventional electrical discharge machine to rotate the workpiece. A conductive preshaped strip of copper as a forming tool is fed (reciprocate) continuously against the rotating workpiece; thus, mirror image of the tool is formed on the circumference of the workpiece. The machining performance of electrical discharge turning process is defined and influenced by its machining parameters, which directly affects the quality of the machined component. This study presents an investigation on the effects of the machining parameters, namely, pulse-on time, peak current, gap voltage, spindle speed and flushing pressure, on the material removal rate (MRR) and surface roughness (Ra) in electrical discharge turning of titanium alloy Ti-6Al-4V. This has been done by means of Taguchi’s design of experiment technique. Analysis of variance as well as regression analysis is performed on the experimental data. The signal-to-noise ratio analysis is employed to find the optimal condition. The experimental results indicate that peak current, gap voltage and pulse-on time are the most significant influencing parameters that contribute more than 90% to material removal rate. In the context of Ra, peak current and pulse-on time come up with more than 82% of contribution. Finally, the obtained predicted optimal results were verified experimentally. It was shown that the error values are all less than 6%, confirming the feasibility and effectiveness of the adopted approach.

Performance Measurement and Data Analysis of Material Removal Rate for Wire Cut Electro Discharge Machining Process

2011 ◽  
Vol 110-116 ◽  
pp. 1683-1690 ◽  
Author(s):  
Vishal Parashar ◽  
A. Rehman ◽  
J.L. Bhagoria
Keyword(s):  
Regression Analysis ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Performance Criteria ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Dielectric Flushing

In this paper, statistical and regression analysis of material removal rate using design of experiments is proposed for WEDM operations. Experimentation was planned as per Taguchi’s mixed orthogonal array. Each experiment has been performed under different cutting conditions of gap voltage, pulse ON time, pulse OFF time, wire feed and dielectric flushing pressure. Stainless Steel grade 304L was selected as a work material to conduct the experiments. From experimental results, the material removal rate was determined for each machining performance criteria. Analysis of variance (ANOVA) technique was used to find out the variables affecting the material removal rate. Assumptions of ANOVA were discussed and carefully examined using analysis of residuals. Variation of the material removal rate with machining parameters was mathematically modeled by using the regression analysis method. The developed model was validated with a set of experimental data and appeared to be satisfactory. Signal to noise ratio was applied to measure the performance characteristics deviating from the actual value. Finally, experimental confirmation was carried out to identify the effectiveness of this proposed method.

Study on Compound Machining of Polyurethane Polishing Pad and Cluster Abrasive Brush Based on MR Effect

2011 ◽  
Vol 487 ◽  
pp. 238-242 ◽  
Author(s):  
Min Li ◽  
Qiu Sheng Yan ◽  
Jia Bin Lu ◽  
Jing Fu Chai
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Machining Parameters ◽  
Polishing Process ◽  
Workpiece Material ◽  
Crystal Silicon ◽  
Polishing Pad ◽  
Mr Effect

Method of compound machining is used to process single crystal silicon and SrTiO3 ceramic substrates, and the factors on effects of compound machining are studied such as magnetic field intensity, processing time, rotating speed of lapping plate and lapping pressure. The results show that the roughness of work pieces processed by compound machining are smaller than that by lapping based on cluster MR effect and polyurethane pad polishing process, while the material removal rate is higher than polyurethane pad polishing process, therefore, compound machining shows its synergistic effect between lapping based on cluster MR effect and polyurethane pad polishing process. The type and properties of workpiece material, and machining parameters both have a significant impact on the roughness and material removal rate of compound machining process of polyurethane polishing pad and cluster abrasive brush based on MR effect.

Sign in / Sign up

Export Citation Format

Share Document